/** ****************************************************************************** * @file stm32l4xx_ll_lpuart.h * @author MCD Application Team * @brief Header file of LPUART LL module. ****************************************************************************** * @attention * * Copyright (c) 2017 STMicroelectronics. * All rights reserved. * * This software is licensed under terms that can be found in the LICENSE file * in the root directory of this software component. * If no LICENSE file comes with this software, it is provided AS-IS. * ****************************************************************************** */ /* Define to prevent recursive inclusion -------------------------------------*/ #ifndef STM32L4xx_LL_LPUART_H #define STM32L4xx_LL_LPUART_H #ifdef __cplusplus extern "C" { #endif /* Includes ------------------------------------------------------------------*/ #include "stm32l4xx.h" /** @addtogroup STM32L4xx_LL_Driver * @{ */ #if defined (LPUART1) /** @defgroup LPUART_LL LPUART * @{ */ /* Private types -------------------------------------------------------------*/ /* Private variables ---------------------------------------------------------*/ #if defined(USART_PRESC_PRESCALER) /** @defgroup LPUART_LL_Private_Variables LPUART Private Variables * @{ */ /* Array used to get the LPUART prescaler division decimal values versus @ref LPUART_LL_EC_PRESCALER values */ static const uint16_t LPUART_PRESCALER_TAB[] = { (uint16_t)1, (uint16_t)2, (uint16_t)4, (uint16_t)6, (uint16_t)8, (uint16_t)10, (uint16_t)12, (uint16_t)16, (uint16_t)32, (uint16_t)64, (uint16_t)128, (uint16_t)256 }; /** * @} */ #endif /* USART_PRESC_PRESCALER */ /* Private constants ---------------------------------------------------------*/ /** @defgroup LPUART_LL_Private_Constants LPUART Private Constants * @{ */ /* Defines used in Baud Rate related macros and corresponding register setting computation */ #define LPUART_LPUARTDIV_FREQ_MUL 256U #define LPUART_BRR_MASK 0x000FFFFFU #define LPUART_BRR_MIN_VALUE 0x00000300U /** * @} */ /* Private macros ------------------------------------------------------------*/ #if defined(USE_FULL_LL_DRIVER) /** @defgroup LPUART_LL_Private_Macros LPUART Private Macros * @{ */ /** * @} */ #endif /*USE_FULL_LL_DRIVER*/ /* Exported types ------------------------------------------------------------*/ #if defined(USE_FULL_LL_DRIVER) /** @defgroup LPUART_LL_ES_INIT LPUART Exported Init structures * @{ */ /** * @brief LL LPUART Init Structure definition */ typedef struct { #if defined(USART_PRESC_PRESCALER) uint32_t PrescalerValue; /*!< Specifies the Prescaler to compute the communication baud rate. This parameter can be a value of @ref LPUART_LL_EC_PRESCALER. This feature can be modified afterwards using unitary function @ref LL_LPUART_SetPrescaler().*/ #endif /* USART_PRESC_PRESCALER */ uint32_t BaudRate; /*!< This field defines expected LPUART communication baud rate. This feature can be modified afterwards using unitary function @ref LL_LPUART_SetBaudRate().*/ uint32_t DataWidth; /*!< Specifies the number of data bits transmitted or received in a frame. This parameter can be a value of @ref LPUART_LL_EC_DATAWIDTH. This feature can be modified afterwards using unitary function @ref LL_LPUART_SetDataWidth().*/ uint32_t StopBits; /*!< Specifies the number of stop bits transmitted. This parameter can be a value of @ref LPUART_LL_EC_STOPBITS. This feature can be modified afterwards using unitary function @ref LL_LPUART_SetStopBitsLength().*/ uint32_t Parity; /*!< Specifies the parity mode. This parameter can be a value of @ref LPUART_LL_EC_PARITY. This feature can be modified afterwards using unitary function @ref LL_LPUART_SetParity().*/ uint32_t TransferDirection; /*!< Specifies whether the Receive and/or Transmit mode is enabled or disabled. This parameter can be a value of @ref LPUART_LL_EC_DIRECTION. This feature can be modified afterwards using unitary function @ref LL_LPUART_SetTransferDirection().*/ uint32_t HardwareFlowControl; /*!< Specifies whether the hardware flow control mode is enabled or disabled. This parameter can be a value of @ref LPUART_LL_EC_HWCONTROL. This feature can be modified afterwards using unitary function @ref LL_LPUART_SetHWFlowCtrl().*/ } LL_LPUART_InitTypeDef; /** * @} */ #endif /* USE_FULL_LL_DRIVER */ /* Exported constants --------------------------------------------------------*/ /** @defgroup LPUART_LL_Exported_Constants LPUART Exported Constants * @{ */ /** @defgroup LPUART_LL_EC_CLEAR_FLAG Clear Flags Defines * @brief Flags defines which can be used with LL_LPUART_WriteReg function * @{ */ #define LL_LPUART_ICR_PECF USART_ICR_PECF /*!< Parity error clear flag */ #define LL_LPUART_ICR_FECF USART_ICR_FECF /*!< Framing error clear flag */ #define LL_LPUART_ICR_NCF USART_ICR_NECF /*!< Noise error detected clear flag */ #define LL_LPUART_ICR_ORECF USART_ICR_ORECF /*!< Overrun error clear flag */ #define LL_LPUART_ICR_IDLECF USART_ICR_IDLECF /*!< Idle line detected clear flag */ #define LL_LPUART_ICR_TCCF USART_ICR_TCCF /*!< Transmission complete clear flag */ #define LL_LPUART_ICR_CTSCF USART_ICR_CTSCF /*!< CTS clear flag */ #define LL_LPUART_ICR_CMCF USART_ICR_CMCF /*!< Character match clear flag */ #define LL_LPUART_ICR_WUCF USART_ICR_WUCF /*!< Wakeup from Stop mode clear flag */ /** * @} */ /** @defgroup LPUART_LL_EC_GET_FLAG Get Flags Defines * @brief Flags defines which can be used with LL_LPUART_ReadReg function * @{ */ #define LL_LPUART_ISR_PE USART_ISR_PE /*!< Parity error flag */ #define LL_LPUART_ISR_FE USART_ISR_FE /*!< Framing error flag */ #define LL_LPUART_ISR_NE USART_ISR_NE /*!< Noise detected flag */ #define LL_LPUART_ISR_ORE USART_ISR_ORE /*!< Overrun error flag */ #define LL_LPUART_ISR_IDLE USART_ISR_IDLE /*!< Idle line detected flag */ #if defined(USART_CR1_FIFOEN) #define LL_LPUART_ISR_RXNE_RXFNE USART_ISR_RXNE_RXFNE /*!< Read data register or RX FIFO not empty flag */ #else #define LL_LPUART_ISR_RXNE USART_ISR_RXNE /*!< Read data register not empty flag */ #endif /* USART_CR1_FIFOEN */ #define LL_LPUART_ISR_TC USART_ISR_TC /*!< Transmission complete flag */ #if defined(USART_CR1_FIFOEN) #define LL_LPUART_ISR_TXE_TXFNF USART_ISR_TXE_TXFNF /*!< Transmit data register empty or TX FIFO Not Full flag*/ #else #define LL_LPUART_ISR_TXE USART_ISR_TXE /*!< Transmit data register empty flag */ #endif /* USART_CR1_FIFOEN */ #define LL_LPUART_ISR_CTSIF USART_ISR_CTSIF /*!< CTS interrupt flag */ #define LL_LPUART_ISR_CTS USART_ISR_CTS /*!< CTS flag */ #define LL_LPUART_ISR_BUSY USART_ISR_BUSY /*!< Busy flag */ #define LL_LPUART_ISR_CMF USART_ISR_CMF /*!< Character match flag */ #define LL_LPUART_ISR_SBKF USART_ISR_SBKF /*!< Send break flag */ #define LL_LPUART_ISR_RWU USART_ISR_RWU /*!< Receiver wakeup from Mute mode flag */ #define LL_LPUART_ISR_WUF USART_ISR_WUF /*!< Wakeup from Stop mode flag */ #define LL_LPUART_ISR_TEACK USART_ISR_TEACK /*!< Transmit enable acknowledge flag */ #define LL_LPUART_ISR_REACK USART_ISR_REACK /*!< Receive enable acknowledge flag */ #if defined(USART_CR1_FIFOEN) #define LL_LPUART_ISR_TXFE USART_ISR_TXFE /*!< TX FIFO empty flag */ #define LL_LPUART_ISR_RXFF USART_ISR_RXFF /*!< RX FIFO full flag */ #define LL_LPUART_ISR_RXFT USART_ISR_RXFT /*!< RX FIFO threshold flag */ #define LL_LPUART_ISR_TXFT USART_ISR_TXFT /*!< TX FIFO threshold flag */ #endif /* USART_CR1_FIFOEN */ /** * @} */ /** @defgroup LPUART_LL_EC_IT IT Defines * @brief IT defines which can be used with LL_LPUART_ReadReg and LL_LPUART_WriteReg functions * @{ */ #define LL_LPUART_CR1_IDLEIE USART_CR1_IDLEIE /*!< IDLE interrupt enable */ #if defined(USART_CR1_FIFOEN) #define LL_LPUART_CR1_RXNEIE_RXFNEIE USART_CR1_RXNEIE_RXFNEIE /*!< Read data register and RXFIFO not empty interrupt enable */ #else #define LL_LPUART_CR1_RXNEIE USART_CR1_RXNEIE /*!< Read data register not empty interrupt enable */ #endif /* USART_CR1_FIFOEN */ #define LL_LPUART_CR1_TCIE USART_CR1_TCIE /*!< Transmission complete interrupt enable */ #if defined(USART_CR1_FIFOEN) #define LL_LPUART_CR1_TXEIE_TXFNFIE USART_CR1_TXEIE_TXFNFIE /*!< Transmit data register empty and TX FIFO not full interrupt enable */ #else #define LL_LPUART_CR1_TXEIE USART_CR1_TXEIE /*!< Transmit data register empty interrupt enable */ #endif /* USART_CR1_FIFOEN */ #define LL_LPUART_CR1_PEIE USART_CR1_PEIE /*!< Parity error */ #define LL_LPUART_CR1_CMIE USART_CR1_CMIE /*!< Character match interrupt enable */ #if defined(USART_CR1_FIFOEN) #define LL_LPUART_CR1_TXFEIE USART_CR1_TXFEIE /*!< TX FIFO empty interrupt enable */ #define LL_LPUART_CR1_RXFFIE USART_CR1_RXFFIE /*!< RX FIFO full interrupt enable */ #endif /* USART_CR1_FIFOEN */ #define LL_LPUART_CR3_EIE USART_CR3_EIE /*!< Error interrupt enable */ #define LL_LPUART_CR3_CTSIE USART_CR3_CTSIE /*!< CTS interrupt enable */ #define LL_LPUART_CR3_WUFIE USART_CR3_WUFIE /*!< Wakeup from Stop mode interrupt enable */ #if defined(USART_CR1_FIFOEN) #define LL_LPUART_CR3_TXFTIE USART_CR3_TXFTIE /*!< TX FIFO threshold interrupt enable */ #define LL_LPUART_CR3_RXFTIE USART_CR3_RXFTIE /*!< RX FIFO threshold interrupt enable */ #endif /* USART_CR1_FIFOEN */ /** * @} */ #if defined(USART_CR1_FIFOEN) /** @defgroup LPUART_LL_EC_FIFOTHRESHOLD FIFO Threshold * @{ */ #define LL_LPUART_FIFOTHRESHOLD_1_8 0x00000000U /*!< FIFO reaches 1/8 of its depth */ #define LL_LPUART_FIFOTHRESHOLD_1_4 0x00000001U /*!< FIFO reaches 1/4 of its depth */ #define LL_LPUART_FIFOTHRESHOLD_1_2 0x00000002U /*!< FIFO reaches 1/2 of its depth */ #define LL_LPUART_FIFOTHRESHOLD_3_4 0x00000003U /*!< FIFO reaches 3/4 of its depth */ #define LL_LPUART_FIFOTHRESHOLD_7_8 0x00000004U /*!< FIFO reaches 7/8 of its depth */ #define LL_LPUART_FIFOTHRESHOLD_8_8 0x00000005U /*!< FIFO becomes empty for TX and full for RX */ /** * @} */ #endif /* USART_CR1_FIFOEN */ /** @defgroup LPUART_LL_EC_DIRECTION Direction * @{ */ #define LL_LPUART_DIRECTION_NONE 0x00000000U /*!< Transmitter and Receiver are disabled */ #define LL_LPUART_DIRECTION_RX USART_CR1_RE /*!< Transmitter is disabled and Receiver is enabled */ #define LL_LPUART_DIRECTION_TX USART_CR1_TE /*!< Transmitter is enabled and Receiver is disabled */ #define LL_LPUART_DIRECTION_TX_RX (USART_CR1_TE |USART_CR1_RE) /*!< Transmitter and Receiver are enabled */ /** * @} */ /** @defgroup LPUART_LL_EC_PARITY Parity Control * @{ */ #define LL_LPUART_PARITY_NONE 0x00000000U /*!< Parity control disabled */ #define LL_LPUART_PARITY_EVEN USART_CR1_PCE /*!< Parity control enabled and Even Parity is selected */ #define LL_LPUART_PARITY_ODD (USART_CR1_PCE | USART_CR1_PS) /*!< Parity control enabled and Odd Parity is selected */ /** * @} */ /** @defgroup LPUART_LL_EC_WAKEUP Wakeup * @{ */ #define LL_LPUART_WAKEUP_IDLELINE 0x00000000U /*!< LPUART wake up from Mute mode on Idle Line */ #define LL_LPUART_WAKEUP_ADDRESSMARK USART_CR1_WAKE /*!< LPUART wake up from Mute mode on Address Mark */ /** * @} */ /** @defgroup LPUART_LL_EC_DATAWIDTH Datawidth * @{ */ #define LL_LPUART_DATAWIDTH_7B USART_CR1_M1 /*!< 7 bits word length : Start bit, 7 data bits, n stop bits */ #define LL_LPUART_DATAWIDTH_8B 0x00000000U /*!< 8 bits word length : Start bit, 8 data bits, n stop bits */ #define LL_LPUART_DATAWIDTH_9B USART_CR1_M0 /*!< 9 bits word length : Start bit, 9 data bits, n stop bits */ /** * @} */ #if defined(USART_PRESC_PRESCALER) /** @defgroup LPUART_LL_EC_PRESCALER Clock Source Prescaler * @{ */ #define LL_LPUART_PRESCALER_DIV1 0x00000000U /*!< Input clock not divided */ #define LL_LPUART_PRESCALER_DIV2 (USART_PRESC_PRESCALER_0) /*!< Input clock divided by 2 */ #define LL_LPUART_PRESCALER_DIV4 (USART_PRESC_PRESCALER_1) /*!< Input clock divided by 4 */ #define LL_LPUART_PRESCALER_DIV6 (USART_PRESC_PRESCALER_1 |\ USART_PRESC_PRESCALER_0) /*!< Input clock divided by 6 */ #define LL_LPUART_PRESCALER_DIV8 (USART_PRESC_PRESCALER_2) /*!< Input clock divided by 8 */ #define LL_LPUART_PRESCALER_DIV10 (USART_PRESC_PRESCALER_2 |\ USART_PRESC_PRESCALER_0) /*!< Input clock divided by 10 */ #define LL_LPUART_PRESCALER_DIV12 (USART_PRESC_PRESCALER_2 |\ USART_PRESC_PRESCALER_1) /*!< Input clock divided by 12 */ #define LL_LPUART_PRESCALER_DIV16 (USART_PRESC_PRESCALER_2 |\ USART_PRESC_PRESCALER_1 |\ USART_PRESC_PRESCALER_0) /*!< Input clock divided by 16 */ #define LL_LPUART_PRESCALER_DIV32 (USART_PRESC_PRESCALER_3) /*!< Input clock divided by 32 */ #define LL_LPUART_PRESCALER_DIV64 (USART_PRESC_PRESCALER_3 |\ USART_PRESC_PRESCALER_0) /*!< Input clock divided by 64 */ #define LL_LPUART_PRESCALER_DIV128 (USART_PRESC_PRESCALER_3 |\ USART_PRESC_PRESCALER_1) /*!< Input clock divided by 128 */ #define LL_LPUART_PRESCALER_DIV256 (USART_PRESC_PRESCALER_3 |\ USART_PRESC_PRESCALER_1 |\ USART_PRESC_PRESCALER_0) /*!< Input clock divided by 256 */ /** * @} */ #endif /* USART_PRESC_PRESCALER */ /** @defgroup LPUART_LL_EC_STOPBITS Stop Bits * @{ */ #define LL_LPUART_STOPBITS_1 0x00000000U /*!< 1 stop bit */ #define LL_LPUART_STOPBITS_2 USART_CR2_STOP_1 /*!< 2 stop bits */ /** * @} */ /** @defgroup LPUART_LL_EC_TXRX TX RX Pins Swap * @{ */ #define LL_LPUART_TXRX_STANDARD 0x00000000U /*!< TX/RX pins are used as defined in standard pinout */ #define LL_LPUART_TXRX_SWAPPED (USART_CR2_SWAP) /*!< TX and RX pins functions are swapped. */ /** * @} */ /** @defgroup LPUART_LL_EC_RXPIN_LEVEL RX Pin Active Level Inversion * @{ */ #define LL_LPUART_RXPIN_LEVEL_STANDARD 0x00000000U /*!< RX pin signal works using the standard logic levels */ #define LL_LPUART_RXPIN_LEVEL_INVERTED (USART_CR2_RXINV) /*!< RX pin signal values are inverted. */ /** * @} */ /** @defgroup LPUART_LL_EC_TXPIN_LEVEL TX Pin Active Level Inversion * @{ */ #define LL_LPUART_TXPIN_LEVEL_STANDARD 0x00000000U /*!< TX pin signal works using the standard logic levels */ #define LL_LPUART_TXPIN_LEVEL_INVERTED (USART_CR2_TXINV) /*!< TX pin signal values are inverted. */ /** * @} */ /** @defgroup LPUART_LL_EC_BINARY_LOGIC Binary Data Inversion * @{ */ #define LL_LPUART_BINARY_LOGIC_POSITIVE 0x00000000U /*!< Logical data from the data register are send/received in positive/direct logic. (1=H, 0=L) */ #define LL_LPUART_BINARY_LOGIC_NEGATIVE USART_CR2_DATAINV /*!< Logical data from the data register are send/received in negative/inverse logic. (1=L, 0=H). The parity bit is also inverted. */ /** * @} */ /** @defgroup LPUART_LL_EC_BITORDER Bit Order * @{ */ #define LL_LPUART_BITORDER_LSBFIRST 0x00000000U /*!< data is transmitted/received with data bit 0 first, following the start bit */ #define LL_LPUART_BITORDER_MSBFIRST USART_CR2_MSBFIRST /*!< data is transmitted/received with the MSB first, following the start bit */ /** * @} */ /** @defgroup LPUART_LL_EC_ADDRESS_DETECT Address Length Detection * @{ */ #define LL_LPUART_ADDRESS_DETECT_4B 0x00000000U /*!< 4-bit address detection method selected */ #define LL_LPUART_ADDRESS_DETECT_7B USART_CR2_ADDM7 /*!< 7-bit address detection (in 8-bit data mode) method selected */ /** * @} */ /** @defgroup LPUART_LL_EC_HWCONTROL Hardware Control * @{ */ #define LL_LPUART_HWCONTROL_NONE 0x00000000U /*!< CTS and RTS hardware flow control disabled */ #define LL_LPUART_HWCONTROL_RTS USART_CR3_RTSE /*!< RTS output enabled, data is only requested when there is space in the receive buffer */ #define LL_LPUART_HWCONTROL_CTS USART_CR3_CTSE /*!< CTS mode enabled, data is only transmitted when the nCTS input is asserted (tied to 0)*/ #define LL_LPUART_HWCONTROL_RTS_CTS (USART_CR3_RTSE | USART_CR3_CTSE) /*!< CTS and RTS hardware flow control enabled */ /** * @} */ /** @defgroup LPUART_LL_EC_WAKEUP_ON Wakeup Activation * @{ */ #define LL_LPUART_WAKEUP_ON_ADDRESS 0x00000000U /*!< Wake up active on address match */ #define LL_LPUART_WAKEUP_ON_STARTBIT USART_CR3_WUS_1 /*!< Wake up active on Start bit detection */ #define LL_LPUART_WAKEUP_ON_RXNE (USART_CR3_WUS_0 | USART_CR3_WUS_1) /*!< Wake up active on RXNE */ /** * @} */ /** @defgroup LPUART_LL_EC_DE_POLARITY Driver Enable Polarity * @{ */ #define LL_LPUART_DE_POLARITY_HIGH 0x00000000U /*!< DE signal is active high */ #define LL_LPUART_DE_POLARITY_LOW USART_CR3_DEP /*!< DE signal is active low */ /** * @} */ /** @defgroup LPUART_LL_EC_DMA_REG_DATA DMA Register Data * @{ */ #define LL_LPUART_DMA_REG_DATA_TRANSMIT 0x00000000U /*!< Get address of data register used for transmission */ #define LL_LPUART_DMA_REG_DATA_RECEIVE 0x00000001U /*!< Get address of data register used for reception */ /** * @} */ /** * @} */ /* Exported macro ------------------------------------------------------------*/ /** @defgroup LPUART_LL_Exported_Macros LPUART Exported Macros * @{ */ /** @defgroup LPUART_LL_EM_WRITE_READ Common Write and read registers Macros * @{ */ /** * @brief Write a value in LPUART register * @param __INSTANCE__ LPUART Instance * @param __REG__ Register to be written * @param __VALUE__ Value to be written in the register * @retval None */ #define LL_LPUART_WriteReg(__INSTANCE__, __REG__, __VALUE__) WRITE_REG(__INSTANCE__->__REG__, (__VALUE__)) /** * @brief Read a value in LPUART register * @param __INSTANCE__ LPUART Instance * @param __REG__ Register to be read * @retval Register value */ #define LL_LPUART_ReadReg(__INSTANCE__, __REG__) READ_REG(__INSTANCE__->__REG__) /** * @} */ /** @defgroup LPUART_LL_EM_Exported_Macros_Helper Helper Macros * @{ */ /** * @brief Compute LPUARTDIV value according to Peripheral Clock and * expected Baud Rate (20-bit value of LPUARTDIV is returned) * @param __PERIPHCLK__ Peripheral Clock frequency used for LPUART Instance @if USART_PRESC_PRESCALER * @param __PRESCALER__ This parameter can be one of the following values: * @arg @ref LL_LPUART_PRESCALER_DIV1 * @arg @ref LL_LPUART_PRESCALER_DIV2 * @arg @ref LL_LPUART_PRESCALER_DIV4 * @arg @ref LL_LPUART_PRESCALER_DIV6 * @arg @ref LL_LPUART_PRESCALER_DIV8 * @arg @ref LL_LPUART_PRESCALER_DIV10 * @arg @ref LL_LPUART_PRESCALER_DIV12 * @arg @ref LL_LPUART_PRESCALER_DIV16 * @arg @ref LL_LPUART_PRESCALER_DIV32 * @arg @ref LL_LPUART_PRESCALER_DIV64 * @arg @ref LL_LPUART_PRESCALER_DIV128 * @arg @ref LL_LPUART_PRESCALER_DIV256 @endif * @param __BAUDRATE__ Baud Rate value to achieve * @retval LPUARTDIV value to be used for BRR register filling */ #if defined(USART_PRESC_PRESCALER) #define __LL_LPUART_DIV(__PERIPHCLK__, __PRESCALER__, __BAUDRATE__) (uint32_t)\ ((((((uint64_t)(__PERIPHCLK__)/(uint64_t)(LPUART_PRESCALER_TAB[(uint16_t)(__PRESCALER__)]))\ * LPUART_LPUARTDIV_FREQ_MUL) + (uint32_t)((__BAUDRATE__)/2U))/(__BAUDRATE__)) & LPUART_BRR_MASK) #else #define __LL_LPUART_DIV(__PERIPHCLK__, __BAUDRATE__) (uint32_t)\ (((((uint64_t)(__PERIPHCLK__)*LPUART_LPUARTDIV_FREQ_MUL) + (uint32_t)((__BAUDRATE__)/2U))/(__BAUDRATE__)) \ & LPUART_BRR_MASK) #endif /* USART_PRESC_PRESCALER */ /** * @} */ /** * @} */ /* Exported functions --------------------------------------------------------*/ /** @defgroup LPUART_LL_Exported_Functions LPUART Exported Functions * @{ */ /** @defgroup LPUART_LL_EF_Configuration Configuration functions * @{ */ /** * @brief LPUART Enable * @rmtoll CR1 UE LL_LPUART_Enable * @param LPUARTx LPUART Instance * @retval None */ __STATIC_INLINE void LL_LPUART_Enable(USART_TypeDef *LPUARTx) { SET_BIT(LPUARTx->CR1, USART_CR1_UE); } /** * @brief LPUART Disable * @note When LPUART is disabled, LPUART prescalers and outputs are stopped immediately, * and current operations are discarded. The configuration of the LPUART is kept, but all the status * flags, in the LPUARTx_ISR are set to their default values. * @note In order to go into low-power mode without generating errors on the line, * the TE bit must be reset before and the software must wait * for the TC bit in the LPUART_ISR to be set before resetting the UE bit. * The DMA requests are also reset when UE = 0 so the DMA channel must * be disabled before resetting the UE bit. * @rmtoll CR1 UE LL_LPUART_Disable * @param LPUARTx LPUART Instance * @retval None */ __STATIC_INLINE void LL_LPUART_Disable(USART_TypeDef *LPUARTx) { CLEAR_BIT(LPUARTx->CR1, USART_CR1_UE); } /** * @brief Indicate if LPUART is enabled * @rmtoll CR1 UE LL_LPUART_IsEnabled * @param LPUARTx LPUART Instance * @retval State of bit (1 or 0). */ __STATIC_INLINE uint32_t LL_LPUART_IsEnabled(const USART_TypeDef *LPUARTx) { return ((READ_BIT(LPUARTx->CR1, USART_CR1_UE) == (USART_CR1_UE)) ? 1UL : 0UL); } #if defined(USART_CR1_FIFOEN) /** * @brief FIFO Mode Enable * @rmtoll CR1 FIFOEN LL_LPUART_EnableFIFO * @param LPUARTx LPUART Instance * @retval None */ __STATIC_INLINE void LL_LPUART_EnableFIFO(USART_TypeDef *LPUARTx) { SET_BIT(LPUARTx->CR1, USART_CR1_FIFOEN); } /** * @brief FIFO Mode Disable * @rmtoll CR1 FIFOEN LL_LPUART_DisableFIFO * @param LPUARTx LPUART Instance * @retval None */ __STATIC_INLINE void LL_LPUART_DisableFIFO(USART_TypeDef *LPUARTx) { CLEAR_BIT(LPUARTx->CR1, USART_CR1_FIFOEN); } /** * @brief Indicate if FIFO Mode is enabled * @rmtoll CR1 FIFOEN LL_LPUART_IsEnabledFIFO * @param LPUARTx LPUART Instance * @retval State of bit (1 or 0). */ __STATIC_INLINE uint32_t LL_LPUART_IsEnabledFIFO(const USART_TypeDef *LPUARTx) { return ((READ_BIT(LPUARTx->CR1, USART_CR1_FIFOEN) == (USART_CR1_FIFOEN)) ? 1UL : 0UL); } /** * @brief Configure TX FIFO Threshold * @rmtoll CR3 TXFTCFG LL_LPUART_SetTXFIFOThreshold * @param LPUARTx LPUART Instance * @param Threshold This parameter can be one of the following values: * @arg @ref LL_LPUART_FIFOTHRESHOLD_1_8 * @arg @ref LL_LPUART_FIFOTHRESHOLD_1_4 * @arg @ref LL_LPUART_FIFOTHRESHOLD_1_2 * @arg @ref LL_LPUART_FIFOTHRESHOLD_3_4 * @arg @ref LL_LPUART_FIFOTHRESHOLD_7_8 * @arg @ref LL_LPUART_FIFOTHRESHOLD_8_8 * @retval None */ __STATIC_INLINE void LL_LPUART_SetTXFIFOThreshold(USART_TypeDef *LPUARTx, uint32_t Threshold) { ATOMIC_MODIFY_REG(LPUARTx->CR3, USART_CR3_TXFTCFG, Threshold << USART_CR3_TXFTCFG_Pos); } /** * @brief Return TX FIFO Threshold Configuration * @rmtoll CR3 TXFTCFG LL_LPUART_GetTXFIFOThreshold * @param LPUARTx LPUART Instance * @retval Returned value can be one of the following values: * @arg @ref LL_LPUART_FIFOTHRESHOLD_1_8 * @arg @ref LL_LPUART_FIFOTHRESHOLD_1_4 * @arg @ref LL_LPUART_FIFOTHRESHOLD_1_2 * @arg @ref LL_LPUART_FIFOTHRESHOLD_3_4 * @arg @ref LL_LPUART_FIFOTHRESHOLD_7_8 * @arg @ref LL_LPUART_FIFOTHRESHOLD_8_8 */ __STATIC_INLINE uint32_t LL_LPUART_GetTXFIFOThreshold(const USART_TypeDef *LPUARTx) { return (uint32_t)(READ_BIT(LPUARTx->CR3, USART_CR3_TXFTCFG) >> USART_CR3_TXFTCFG_Pos); } /** * @brief Configure RX FIFO Threshold * @rmtoll CR3 RXFTCFG LL_LPUART_SetRXFIFOThreshold * @param LPUARTx LPUART Instance * @param Threshold This parameter can be one of the following values: * @arg @ref LL_LPUART_FIFOTHRESHOLD_1_8 * @arg @ref LL_LPUART_FIFOTHRESHOLD_1_4 * @arg @ref LL_LPUART_FIFOTHRESHOLD_1_2 * @arg @ref LL_LPUART_FIFOTHRESHOLD_3_4 * @arg @ref LL_LPUART_FIFOTHRESHOLD_7_8 * @arg @ref LL_LPUART_FIFOTHRESHOLD_8_8 * @retval None */ __STATIC_INLINE void LL_LPUART_SetRXFIFOThreshold(USART_TypeDef *LPUARTx, uint32_t Threshold) { ATOMIC_MODIFY_REG(LPUARTx->CR3, USART_CR3_RXFTCFG, Threshold << USART_CR3_RXFTCFG_Pos); } /** * @brief Return RX FIFO Threshold Configuration * @rmtoll CR3 RXFTCFG LL_LPUART_GetRXFIFOThreshold * @param LPUARTx LPUART Instance * @retval Returned value can be one of the following values: * @arg @ref LL_LPUART_FIFOTHRESHOLD_1_8 * @arg @ref LL_LPUART_FIFOTHRESHOLD_1_4 * @arg @ref LL_LPUART_FIFOTHRESHOLD_1_2 * @arg @ref LL_LPUART_FIFOTHRESHOLD_3_4 * @arg @ref LL_LPUART_FIFOTHRESHOLD_7_8 * @arg @ref LL_LPUART_FIFOTHRESHOLD_8_8 */ __STATIC_INLINE uint32_t LL_LPUART_GetRXFIFOThreshold(const USART_TypeDef *LPUARTx) { return (uint32_t)(READ_BIT(LPUARTx->CR3, USART_CR3_RXFTCFG) >> USART_CR3_RXFTCFG_Pos); } /** * @brief Configure TX and RX FIFOs Threshold * @rmtoll CR3 TXFTCFG LL_LPUART_ConfigFIFOsThreshold\n * CR3 RXFTCFG LL_LPUART_ConfigFIFOsThreshold * @param LPUARTx LPUART Instance * @param TXThreshold This parameter can be one of the following values: * @arg @ref LL_LPUART_FIFOTHRESHOLD_1_8 * @arg @ref LL_LPUART_FIFOTHRESHOLD_1_4 * @arg @ref LL_LPUART_FIFOTHRESHOLD_1_2 * @arg @ref LL_LPUART_FIFOTHRESHOLD_3_4 * @arg @ref LL_LPUART_FIFOTHRESHOLD_7_8 * @arg @ref LL_LPUART_FIFOTHRESHOLD_8_8 * @param RXThreshold This parameter can be one of the following values: * @arg @ref LL_LPUART_FIFOTHRESHOLD_1_8 * @arg @ref LL_LPUART_FIFOTHRESHOLD_1_4 * @arg @ref LL_LPUART_FIFOTHRESHOLD_1_2 * @arg @ref LL_LPUART_FIFOTHRESHOLD_3_4 * @arg @ref LL_LPUART_FIFOTHRESHOLD_7_8 * @arg @ref LL_LPUART_FIFOTHRESHOLD_8_8 * @retval None */ __STATIC_INLINE void LL_LPUART_ConfigFIFOsThreshold(USART_TypeDef *LPUARTx, uint32_t TXThreshold, uint32_t RXThreshold) { ATOMIC_MODIFY_REG(LPUARTx->CR3, USART_CR3_TXFTCFG | USART_CR3_RXFTCFG, (TXThreshold << USART_CR3_TXFTCFG_Pos) | \ (RXThreshold << USART_CR3_RXFTCFG_Pos)); } #endif /* USART_CR1_FIFOEN */ /** * @brief LPUART enabled in STOP Mode * @note When this function is enabled, LPUART is able to wake up the MCU from Stop mode, provided that * LPUART clock selection is HSI or LSE in RCC. * @rmtoll CR1 UESM LL_LPUART_EnableInStopMode * @param LPUARTx LPUART Instance * @retval None */ __STATIC_INLINE void LL_LPUART_EnableInStopMode(USART_TypeDef *LPUARTx) { ATOMIC_SET_BIT(LPUARTx->CR1, USART_CR1_UESM); } /** * @brief LPUART disabled in STOP Mode * @note When this function is disabled, LPUART is not able to wake up the MCU from Stop mode * @rmtoll CR1 UESM LL_LPUART_DisableInStopMode * @param LPUARTx LPUART Instance * @retval None */ __STATIC_INLINE void LL_LPUART_DisableInStopMode(USART_TypeDef *LPUARTx) { ATOMIC_CLEAR_BIT(LPUARTx->CR1, USART_CR1_UESM); } /** * @brief Indicate if LPUART is enabled in STOP Mode * (able to wake up MCU from Stop mode or not) * @rmtoll CR1 UESM LL_LPUART_IsEnabledInStopMode * @param LPUARTx LPUART Instance * @retval State of bit (1 or 0). */ __STATIC_INLINE uint32_t LL_LPUART_IsEnabledInStopMode(const USART_TypeDef *LPUARTx) { return ((READ_BIT(LPUARTx->CR1, USART_CR1_UESM) == (USART_CR1_UESM)) ? 1UL : 0UL); } #if defined(USART_CR3_UCESM) /** * @brief LPUART Clock enabled in STOP Mode * @note When this function is called, LPUART Clock is enabled while in STOP mode * @rmtoll CR3 UCESM LL_LPUART_EnableClockInStopMode * @param LPUARTx LPUART Instance * @retval None */ __STATIC_INLINE void LL_LPUART_EnableClockInStopMode(USART_TypeDef *LPUARTx) { ATOMIC_SET_BIT(LPUARTx->CR3, USART_CR3_UCESM); } /** * @brief LPUART clock disabled in STOP Mode * @note When this function is called, LPUART Clock is disabled while in STOP mode * @rmtoll CR3 UCESM LL_LPUART_DisableClockInStopMode * @param LPUARTx LPUART Instance * @retval None */ __STATIC_INLINE void LL_LPUART_DisableClockInStopMode(USART_TypeDef *LPUARTx) { ATOMIC_CLEAR_BIT(LPUARTx->CR3, USART_CR3_UCESM); } /** * @brief Indicate if LPUART clock is enabled in STOP Mode * @rmtoll CR3 UCESM LL_LPUART_IsClockEnabledInStopMode * @param LPUARTx LPUART Instance * @retval State of bit (1 or 0). */ __STATIC_INLINE uint32_t LL_LPUART_IsClockEnabledInStopMode(const USART_TypeDef *LPUARTx) { return ((READ_BIT(LPUARTx->CR3, USART_CR3_UCESM) == (USART_CR3_UCESM)) ? 1UL : 0UL); } #endif /* USART_CR3_UCESM */ /** * @brief Receiver Enable (Receiver is enabled and begins searching for a start bit) * @rmtoll CR1 RE LL_LPUART_EnableDirectionRx * @param LPUARTx LPUART Instance * @retval None */ __STATIC_INLINE void LL_LPUART_EnableDirectionRx(USART_TypeDef *LPUARTx) { ATOMIC_SET_BIT(LPUARTx->CR1, USART_CR1_RE); } /** * @brief Receiver Disable * @rmtoll CR1 RE LL_LPUART_DisableDirectionRx * @param LPUARTx LPUART Instance * @retval None */ __STATIC_INLINE void LL_LPUART_DisableDirectionRx(USART_TypeDef *LPUARTx) { ATOMIC_CLEAR_BIT(LPUARTx->CR1, USART_CR1_RE); } /** * @brief Transmitter Enable * @rmtoll CR1 TE LL_LPUART_EnableDirectionTx * @param LPUARTx LPUART Instance * @retval None */ __STATIC_INLINE void LL_LPUART_EnableDirectionTx(USART_TypeDef *LPUARTx) { ATOMIC_SET_BIT(LPUARTx->CR1, USART_CR1_TE); } /** * @brief Transmitter Disable * @rmtoll CR1 TE LL_LPUART_DisableDirectionTx * @param LPUARTx LPUART Instance * @retval None */ __STATIC_INLINE void LL_LPUART_DisableDirectionTx(USART_TypeDef *LPUARTx) { ATOMIC_CLEAR_BIT(LPUARTx->CR1, USART_CR1_TE); } /** * @brief Configure simultaneously enabled/disabled states * of Transmitter and Receiver * @rmtoll CR1 RE LL_LPUART_SetTransferDirection\n * CR1 TE LL_LPUART_SetTransferDirection * @param LPUARTx LPUART Instance * @param TransferDirection This parameter can be one of the following values: * @arg @ref LL_LPUART_DIRECTION_NONE * @arg @ref LL_LPUART_DIRECTION_RX * @arg @ref LL_LPUART_DIRECTION_TX * @arg @ref LL_LPUART_DIRECTION_TX_RX * @retval None */ __STATIC_INLINE void LL_LPUART_SetTransferDirection(USART_TypeDef *LPUARTx, uint32_t TransferDirection) { ATOMIC_MODIFY_REG(LPUARTx->CR1, USART_CR1_RE | USART_CR1_TE, TransferDirection); } /** * @brief Return enabled/disabled states of Transmitter and Receiver * @rmtoll CR1 RE LL_LPUART_GetTransferDirection\n * CR1 TE LL_LPUART_GetTransferDirection * @param LPUARTx LPUART Instance * @retval Returned value can be one of the following values: * @arg @ref LL_LPUART_DIRECTION_NONE * @arg @ref LL_LPUART_DIRECTION_RX * @arg @ref LL_LPUART_DIRECTION_TX * @arg @ref LL_LPUART_DIRECTION_TX_RX */ __STATIC_INLINE uint32_t LL_LPUART_GetTransferDirection(const USART_TypeDef *LPUARTx) { return (uint32_t)(READ_BIT(LPUARTx->CR1, USART_CR1_RE | USART_CR1_TE)); } /** * @brief Configure Parity (enabled/disabled and parity mode if enabled) * @note This function selects if hardware parity control (generation and detection) is enabled or disabled. * When the parity control is enabled (Odd or Even), computed parity bit is inserted at the MSB position * (depending on data width) and parity is checked on the received data. * @rmtoll CR1 PS LL_LPUART_SetParity\n * CR1 PCE LL_LPUART_SetParity * @param LPUARTx LPUART Instance * @param Parity This parameter can be one of the following values: * @arg @ref LL_LPUART_PARITY_NONE * @arg @ref LL_LPUART_PARITY_EVEN * @arg @ref LL_LPUART_PARITY_ODD * @retval None */ __STATIC_INLINE void LL_LPUART_SetParity(USART_TypeDef *LPUARTx, uint32_t Parity) { MODIFY_REG(LPUARTx->CR1, USART_CR1_PS | USART_CR1_PCE, Parity); } /** * @brief Return Parity configuration (enabled/disabled and parity mode if enabled) * @rmtoll CR1 PS LL_LPUART_GetParity\n * CR1 PCE LL_LPUART_GetParity * @param LPUARTx LPUART Instance * @retval Returned value can be one of the following values: * @arg @ref LL_LPUART_PARITY_NONE * @arg @ref LL_LPUART_PARITY_EVEN * @arg @ref LL_LPUART_PARITY_ODD */ __STATIC_INLINE uint32_t LL_LPUART_GetParity(const USART_TypeDef *LPUARTx) { return (uint32_t)(READ_BIT(LPUARTx->CR1, USART_CR1_PS | USART_CR1_PCE)); } /** * @brief Set Receiver Wake Up method from Mute mode. * @rmtoll CR1 WAKE LL_LPUART_SetWakeUpMethod * @param LPUARTx LPUART Instance * @param Method This parameter can be one of the following values: * @arg @ref LL_LPUART_WAKEUP_IDLELINE * @arg @ref LL_LPUART_WAKEUP_ADDRESSMARK * @retval None */ __STATIC_INLINE void LL_LPUART_SetWakeUpMethod(USART_TypeDef *LPUARTx, uint32_t Method) { MODIFY_REG(LPUARTx->CR1, USART_CR1_WAKE, Method); } /** * @brief Return Receiver Wake Up method from Mute mode * @rmtoll CR1 WAKE LL_LPUART_GetWakeUpMethod * @param LPUARTx LPUART Instance * @retval Returned value can be one of the following values: * @arg @ref LL_LPUART_WAKEUP_IDLELINE * @arg @ref LL_LPUART_WAKEUP_ADDRESSMARK */ __STATIC_INLINE uint32_t LL_LPUART_GetWakeUpMethod(const USART_TypeDef *LPUARTx) { return (uint32_t)(READ_BIT(LPUARTx->CR1, USART_CR1_WAKE)); } /** * @brief Set Word length (nb of data bits, excluding start and stop bits) * @rmtoll CR1 M LL_LPUART_SetDataWidth * @param LPUARTx LPUART Instance * @param DataWidth This parameter can be one of the following values: * @arg @ref LL_LPUART_DATAWIDTH_7B * @arg @ref LL_LPUART_DATAWIDTH_8B * @arg @ref LL_LPUART_DATAWIDTH_9B * @retval None */ __STATIC_INLINE void LL_LPUART_SetDataWidth(USART_TypeDef *LPUARTx, uint32_t DataWidth) { MODIFY_REG(LPUARTx->CR1, USART_CR1_M, DataWidth); } /** * @brief Return Word length (i.e. nb of data bits, excluding start and stop bits) * @rmtoll CR1 M LL_LPUART_GetDataWidth * @param LPUARTx LPUART Instance * @retval Returned value can be one of the following values: * @arg @ref LL_LPUART_DATAWIDTH_7B * @arg @ref LL_LPUART_DATAWIDTH_8B * @arg @ref LL_LPUART_DATAWIDTH_9B */ __STATIC_INLINE uint32_t LL_LPUART_GetDataWidth(const USART_TypeDef *LPUARTx) { return (uint32_t)(READ_BIT(LPUARTx->CR1, USART_CR1_M)); } /** * @brief Allow switch between Mute Mode and Active mode * @rmtoll CR1 MME LL_LPUART_EnableMuteMode * @param LPUARTx LPUART Instance * @retval None */ __STATIC_INLINE void LL_LPUART_EnableMuteMode(USART_TypeDef *LPUARTx) { ATOMIC_SET_BIT(LPUARTx->CR1, USART_CR1_MME); } /** * @brief Prevent Mute Mode use. Set Receiver in active mode permanently. * @rmtoll CR1 MME LL_LPUART_DisableMuteMode * @param LPUARTx LPUART Instance * @retval None */ __STATIC_INLINE void LL_LPUART_DisableMuteMode(USART_TypeDef *LPUARTx) { ATOMIC_CLEAR_BIT(LPUARTx->CR1, USART_CR1_MME); } /** * @brief Indicate if switch between Mute Mode and Active mode is allowed * @rmtoll CR1 MME LL_LPUART_IsEnabledMuteMode * @param LPUARTx LPUART Instance * @retval State of bit (1 or 0). */ __STATIC_INLINE uint32_t LL_LPUART_IsEnabledMuteMode(const USART_TypeDef *LPUARTx) { return ((READ_BIT(LPUARTx->CR1, USART_CR1_MME) == (USART_CR1_MME)) ? 1UL : 0UL); } #if defined(USART_PRESC_PRESCALER) /** * @brief Configure Clock source prescaler for baudrate generator and oversampling * @rmtoll PRESC PRESCALER LL_LPUART_SetPrescaler * @param LPUARTx LPUART Instance * @param PrescalerValue This parameter can be one of the following values: * @arg @ref LL_LPUART_PRESCALER_DIV1 * @arg @ref LL_LPUART_PRESCALER_DIV2 * @arg @ref LL_LPUART_PRESCALER_DIV4 * @arg @ref LL_LPUART_PRESCALER_DIV6 * @arg @ref LL_LPUART_PRESCALER_DIV8 * @arg @ref LL_LPUART_PRESCALER_DIV10 * @arg @ref LL_LPUART_PRESCALER_DIV12 * @arg @ref LL_LPUART_PRESCALER_DIV16 * @arg @ref LL_LPUART_PRESCALER_DIV32 * @arg @ref LL_LPUART_PRESCALER_DIV64 * @arg @ref LL_LPUART_PRESCALER_DIV128 * @arg @ref LL_LPUART_PRESCALER_DIV256 * @retval None */ __STATIC_INLINE void LL_LPUART_SetPrescaler(USART_TypeDef *LPUARTx, uint32_t PrescalerValue) { MODIFY_REG(LPUARTx->PRESC, USART_PRESC_PRESCALER, (uint16_t)PrescalerValue); } /** * @brief Retrieve the Clock source prescaler for baudrate generator and oversampling * @rmtoll PRESC PRESCALER LL_LPUART_GetPrescaler * @param LPUARTx LPUART Instance * @retval Returned value can be one of the following values: * @arg @ref LL_LPUART_PRESCALER_DIV1 * @arg @ref LL_LPUART_PRESCALER_DIV2 * @arg @ref LL_LPUART_PRESCALER_DIV4 * @arg @ref LL_LPUART_PRESCALER_DIV6 * @arg @ref LL_LPUART_PRESCALER_DIV8 * @arg @ref LL_LPUART_PRESCALER_DIV10 * @arg @ref LL_LPUART_PRESCALER_DIV12 * @arg @ref LL_LPUART_PRESCALER_DIV16 * @arg @ref LL_LPUART_PRESCALER_DIV32 * @arg @ref LL_LPUART_PRESCALER_DIV64 * @arg @ref LL_LPUART_PRESCALER_DIV128 * @arg @ref LL_LPUART_PRESCALER_DIV256 */ __STATIC_INLINE uint32_t LL_LPUART_GetPrescaler(const USART_TypeDef *LPUARTx) { return (uint32_t)(READ_BIT(LPUARTx->PRESC, USART_PRESC_PRESCALER)); } #endif /* USART_PRESC_PRESCALER */ /** * @brief Set the length of the stop bits * @rmtoll CR2 STOP LL_LPUART_SetStopBitsLength * @param LPUARTx LPUART Instance * @param StopBits This parameter can be one of the following values: * @arg @ref LL_LPUART_STOPBITS_1 * @arg @ref LL_LPUART_STOPBITS_2 * @retval None */ __STATIC_INLINE void LL_LPUART_SetStopBitsLength(USART_TypeDef *LPUARTx, uint32_t StopBits) { MODIFY_REG(LPUARTx->CR2, USART_CR2_STOP, StopBits); } /** * @brief Retrieve the length of the stop bits * @rmtoll CR2 STOP LL_LPUART_GetStopBitsLength * @param LPUARTx LPUART Instance * @retval Returned value can be one of the following values: * @arg @ref LL_LPUART_STOPBITS_1 * @arg @ref LL_LPUART_STOPBITS_2 */ __STATIC_INLINE uint32_t LL_LPUART_GetStopBitsLength(const USART_TypeDef *LPUARTx) { return (uint32_t)(READ_BIT(LPUARTx->CR2, USART_CR2_STOP)); } /** * @brief Configure Character frame format (Datawidth, Parity control, Stop Bits) * @note Call of this function is equivalent to following function call sequence : * - Data Width configuration using @ref LL_LPUART_SetDataWidth() function * - Parity Control and mode configuration using @ref LL_LPUART_SetParity() function * - Stop bits configuration using @ref LL_LPUART_SetStopBitsLength() function * @rmtoll CR1 PS LL_LPUART_ConfigCharacter\n * CR1 PCE LL_LPUART_ConfigCharacter\n * CR1 M LL_LPUART_ConfigCharacter\n * CR2 STOP LL_LPUART_ConfigCharacter * @param LPUARTx LPUART Instance * @param DataWidth This parameter can be one of the following values: * @arg @ref LL_LPUART_DATAWIDTH_7B * @arg @ref LL_LPUART_DATAWIDTH_8B * @arg @ref LL_LPUART_DATAWIDTH_9B * @param Parity This parameter can be one of the following values: * @arg @ref LL_LPUART_PARITY_NONE * @arg @ref LL_LPUART_PARITY_EVEN * @arg @ref LL_LPUART_PARITY_ODD * @param StopBits This parameter can be one of the following values: * @arg @ref LL_LPUART_STOPBITS_1 * @arg @ref LL_LPUART_STOPBITS_2 * @retval None */ __STATIC_INLINE void LL_LPUART_ConfigCharacter(USART_TypeDef *LPUARTx, uint32_t DataWidth, uint32_t Parity, uint32_t StopBits) { MODIFY_REG(LPUARTx->CR1, USART_CR1_PS | USART_CR1_PCE | USART_CR1_M, Parity | DataWidth); MODIFY_REG(LPUARTx->CR2, USART_CR2_STOP, StopBits); } /** * @brief Configure TX/RX pins swapping setting. * @rmtoll CR2 SWAP LL_LPUART_SetTXRXSwap * @param LPUARTx LPUART Instance * @param SwapConfig This parameter can be one of the following values: * @arg @ref LL_LPUART_TXRX_STANDARD * @arg @ref LL_LPUART_TXRX_SWAPPED * @retval None */ __STATIC_INLINE void LL_LPUART_SetTXRXSwap(USART_TypeDef *LPUARTx, uint32_t SwapConfig) { MODIFY_REG(LPUARTx->CR2, USART_CR2_SWAP, SwapConfig); } /** * @brief Retrieve TX/RX pins swapping configuration. * @rmtoll CR2 SWAP LL_LPUART_GetTXRXSwap * @param LPUARTx LPUART Instance * @retval Returned value can be one of the following values: * @arg @ref LL_LPUART_TXRX_STANDARD * @arg @ref LL_LPUART_TXRX_SWAPPED */ __STATIC_INLINE uint32_t LL_LPUART_GetTXRXSwap(const USART_TypeDef *LPUARTx) { return (uint32_t)(READ_BIT(LPUARTx->CR2, USART_CR2_SWAP)); } /** * @brief Configure RX pin active level logic * @rmtoll CR2 RXINV LL_LPUART_SetRXPinLevel * @param LPUARTx LPUART Instance * @param PinInvMethod This parameter can be one of the following values: * @arg @ref LL_LPUART_RXPIN_LEVEL_STANDARD * @arg @ref LL_LPUART_RXPIN_LEVEL_INVERTED * @retval None */ __STATIC_INLINE void LL_LPUART_SetRXPinLevel(USART_TypeDef *LPUARTx, uint32_t PinInvMethod) { MODIFY_REG(LPUARTx->CR2, USART_CR2_RXINV, PinInvMethod); } /** * @brief Retrieve RX pin active level logic configuration * @rmtoll CR2 RXINV LL_LPUART_GetRXPinLevel * @param LPUARTx LPUART Instance * @retval Returned value can be one of the following values: * @arg @ref LL_LPUART_RXPIN_LEVEL_STANDARD * @arg @ref LL_LPUART_RXPIN_LEVEL_INVERTED */ __STATIC_INLINE uint32_t LL_LPUART_GetRXPinLevel(const USART_TypeDef *LPUARTx) { return (uint32_t)(READ_BIT(LPUARTx->CR2, USART_CR2_RXINV)); } /** * @brief Configure TX pin active level logic * @rmtoll CR2 TXINV LL_LPUART_SetTXPinLevel * @param LPUARTx LPUART Instance * @param PinInvMethod This parameter can be one of the following values: * @arg @ref LL_LPUART_TXPIN_LEVEL_STANDARD * @arg @ref LL_LPUART_TXPIN_LEVEL_INVERTED * @retval None */ __STATIC_INLINE void LL_LPUART_SetTXPinLevel(USART_TypeDef *LPUARTx, uint32_t PinInvMethod) { MODIFY_REG(LPUARTx->CR2, USART_CR2_TXINV, PinInvMethod); } /** * @brief Retrieve TX pin active level logic configuration * @rmtoll CR2 TXINV LL_LPUART_GetTXPinLevel * @param LPUARTx LPUART Instance * @retval Returned value can be one of the following values: * @arg @ref LL_LPUART_TXPIN_LEVEL_STANDARD * @arg @ref LL_LPUART_TXPIN_LEVEL_INVERTED */ __STATIC_INLINE uint32_t LL_LPUART_GetTXPinLevel(const USART_TypeDef *LPUARTx) { return (uint32_t)(READ_BIT(LPUARTx->CR2, USART_CR2_TXINV)); } /** * @brief Configure Binary data logic. * * @note Allow to define how Logical data from the data register are send/received : * either in positive/direct logic (1=H, 0=L) or in negative/inverse logic (1=L, 0=H) * @rmtoll CR2 DATAINV LL_LPUART_SetBinaryDataLogic * @param LPUARTx LPUART Instance * @param DataLogic This parameter can be one of the following values: * @arg @ref LL_LPUART_BINARY_LOGIC_POSITIVE * @arg @ref LL_LPUART_BINARY_LOGIC_NEGATIVE * @retval None */ __STATIC_INLINE void LL_LPUART_SetBinaryDataLogic(USART_TypeDef *LPUARTx, uint32_t DataLogic) { MODIFY_REG(LPUARTx->CR2, USART_CR2_DATAINV, DataLogic); } /** * @brief Retrieve Binary data configuration * @rmtoll CR2 DATAINV LL_LPUART_GetBinaryDataLogic * @param LPUARTx LPUART Instance * @retval Returned value can be one of the following values: * @arg @ref LL_LPUART_BINARY_LOGIC_POSITIVE * @arg @ref LL_LPUART_BINARY_LOGIC_NEGATIVE */ __STATIC_INLINE uint32_t LL_LPUART_GetBinaryDataLogic(const USART_TypeDef *LPUARTx) { return (uint32_t)(READ_BIT(LPUARTx->CR2, USART_CR2_DATAINV)); } /** * @brief Configure transfer bit order (either Less or Most Significant Bit First) * @note MSB First means data is transmitted/received with the MSB first, following the start bit. * LSB First means data is transmitted/received with data bit 0 first, following the start bit. * @rmtoll CR2 MSBFIRST LL_LPUART_SetTransferBitOrder * @param LPUARTx LPUART Instance * @param BitOrder This parameter can be one of the following values: * @arg @ref LL_LPUART_BITORDER_LSBFIRST * @arg @ref LL_LPUART_BITORDER_MSBFIRST * @retval None */ __STATIC_INLINE void LL_LPUART_SetTransferBitOrder(USART_TypeDef *LPUARTx, uint32_t BitOrder) { MODIFY_REG(LPUARTx->CR2, USART_CR2_MSBFIRST, BitOrder); } /** * @brief Return transfer bit order (either Less or Most Significant Bit First) * @note MSB First means data is transmitted/received with the MSB first, following the start bit. * LSB First means data is transmitted/received with data bit 0 first, following the start bit. * @rmtoll CR2 MSBFIRST LL_LPUART_GetTransferBitOrder * @param LPUARTx LPUART Instance * @retval Returned value can be one of the following values: * @arg @ref LL_LPUART_BITORDER_LSBFIRST * @arg @ref LL_LPUART_BITORDER_MSBFIRST */ __STATIC_INLINE uint32_t LL_LPUART_GetTransferBitOrder(const USART_TypeDef *LPUARTx) { return (uint32_t)(READ_BIT(LPUARTx->CR2, USART_CR2_MSBFIRST)); } /** * @brief Set Address of the LPUART node. * @note This is used in multiprocessor communication during Mute mode or Stop mode, * for wake up with address mark detection. * @note 4bits address node is used when 4-bit Address Detection is selected in ADDM7. * (b7-b4 should be set to 0) * 8bits address node is used when 7-bit Address Detection is selected in ADDM7. * (This is used in multiprocessor communication during Mute mode or Stop mode, * for wake up with 7-bit address mark detection. * The MSB of the character sent by the transmitter should be equal to 1. * It may also be used for character detection during normal reception, * Mute mode inactive (for example, end of block detection in ModBus protocol). * In this case, the whole received character (8-bit) is compared to the ADD[7:0] * value and CMF flag is set on match) * @rmtoll CR2 ADD LL_LPUART_ConfigNodeAddress\n * CR2 ADDM7 LL_LPUART_ConfigNodeAddress * @param LPUARTx LPUART Instance * @param AddressLen This parameter can be one of the following values: * @arg @ref LL_LPUART_ADDRESS_DETECT_4B * @arg @ref LL_LPUART_ADDRESS_DETECT_7B * @param NodeAddress 4 or 7 bit Address of the LPUART node. * @retval None */ __STATIC_INLINE void LL_LPUART_ConfigNodeAddress(USART_TypeDef *LPUARTx, uint32_t AddressLen, uint32_t NodeAddress) { MODIFY_REG(LPUARTx->CR2, USART_CR2_ADD | USART_CR2_ADDM7, (uint32_t)(AddressLen | (NodeAddress << USART_CR2_ADD_Pos))); } /** * @brief Return 8 bit Address of the LPUART node as set in ADD field of CR2. * @note If 4-bit Address Detection is selected in ADDM7, * only 4bits (b3-b0) of returned value are relevant (b31-b4 are not relevant) * If 7-bit Address Detection is selected in ADDM7, * only 8bits (b7-b0) of returned value are relevant (b31-b8 are not relevant) * @rmtoll CR2 ADD LL_LPUART_GetNodeAddress * @param LPUARTx LPUART Instance * @retval Address of the LPUART node (Value between Min_Data=0 and Max_Data=255) */ __STATIC_INLINE uint32_t LL_LPUART_GetNodeAddress(const USART_TypeDef *LPUARTx) { return (uint32_t)(READ_BIT(LPUARTx->CR2, USART_CR2_ADD) >> USART_CR2_ADD_Pos); } /** * @brief Return Length of Node Address used in Address Detection mode (7-bit or 4-bit) * @rmtoll CR2 ADDM7 LL_LPUART_GetNodeAddressLen * @param LPUARTx LPUART Instance * @retval Returned value can be one of the following values: * @arg @ref LL_LPUART_ADDRESS_DETECT_4B * @arg @ref LL_LPUART_ADDRESS_DETECT_7B */ __STATIC_INLINE uint32_t LL_LPUART_GetNodeAddressLen(const USART_TypeDef *LPUARTx) { return (uint32_t)(READ_BIT(LPUARTx->CR2, USART_CR2_ADDM7)); } /** * @brief Enable RTS HW Flow Control * @rmtoll CR3 RTSE LL_LPUART_EnableRTSHWFlowCtrl * @param LPUARTx LPUART Instance * @retval None */ __STATIC_INLINE void LL_LPUART_EnableRTSHWFlowCtrl(USART_TypeDef *LPUARTx) { SET_BIT(LPUARTx->CR3, USART_CR3_RTSE); } /** * @brief Disable RTS HW Flow Control * @rmtoll CR3 RTSE LL_LPUART_DisableRTSHWFlowCtrl * @param LPUARTx LPUART Instance * @retval None */ __STATIC_INLINE void LL_LPUART_DisableRTSHWFlowCtrl(USART_TypeDef *LPUARTx) { CLEAR_BIT(LPUARTx->CR3, USART_CR3_RTSE); } /** * @brief Enable CTS HW Flow Control * @rmtoll CR3 CTSE LL_LPUART_EnableCTSHWFlowCtrl * @param LPUARTx LPUART Instance * @retval None */ __STATIC_INLINE void LL_LPUART_EnableCTSHWFlowCtrl(USART_TypeDef *LPUARTx) { SET_BIT(LPUARTx->CR3, USART_CR3_CTSE); } /** * @brief Disable CTS HW Flow Control * @rmtoll CR3 CTSE LL_LPUART_DisableCTSHWFlowCtrl * @param LPUARTx LPUART Instance * @retval None */ __STATIC_INLINE void LL_LPUART_DisableCTSHWFlowCtrl(USART_TypeDef *LPUARTx) { CLEAR_BIT(LPUARTx->CR3, USART_CR3_CTSE); } /** * @brief Configure HW Flow Control mode (both CTS and RTS) * @rmtoll CR3 RTSE LL_LPUART_SetHWFlowCtrl\n * CR3 CTSE LL_LPUART_SetHWFlowCtrl * @param LPUARTx LPUART Instance * @param HardwareFlowControl This parameter can be one of the following values: * @arg @ref LL_LPUART_HWCONTROL_NONE * @arg @ref LL_LPUART_HWCONTROL_RTS * @arg @ref LL_LPUART_HWCONTROL_CTS * @arg @ref LL_LPUART_HWCONTROL_RTS_CTS * @retval None */ __STATIC_INLINE void LL_LPUART_SetHWFlowCtrl(USART_TypeDef *LPUARTx, uint32_t HardwareFlowControl) { MODIFY_REG(LPUARTx->CR3, USART_CR3_RTSE | USART_CR3_CTSE, HardwareFlowControl); } /** * @brief Return HW Flow Control configuration (both CTS and RTS) * @rmtoll CR3 RTSE LL_LPUART_GetHWFlowCtrl\n * CR3 CTSE LL_LPUART_GetHWFlowCtrl * @param LPUARTx LPUART Instance * @retval Returned value can be one of the following values: * @arg @ref LL_LPUART_HWCONTROL_NONE * @arg @ref LL_LPUART_HWCONTROL_RTS * @arg @ref LL_LPUART_HWCONTROL_CTS * @arg @ref LL_LPUART_HWCONTROL_RTS_CTS */ __STATIC_INLINE uint32_t LL_LPUART_GetHWFlowCtrl(const USART_TypeDef *LPUARTx) { return (uint32_t)(READ_BIT(LPUARTx->CR3, USART_CR3_RTSE | USART_CR3_CTSE)); } /** * @brief Enable Overrun detection * @rmtoll CR3 OVRDIS LL_LPUART_EnableOverrunDetect * @param LPUARTx LPUART Instance * @retval None */ __STATIC_INLINE void LL_LPUART_EnableOverrunDetect(USART_TypeDef *LPUARTx) { CLEAR_BIT(LPUARTx->CR3, USART_CR3_OVRDIS); } /** * @brief Disable Overrun detection * @rmtoll CR3 OVRDIS LL_LPUART_DisableOverrunDetect * @param LPUARTx LPUART Instance * @retval None */ __STATIC_INLINE void LL_LPUART_DisableOverrunDetect(USART_TypeDef *LPUARTx) { SET_BIT(LPUARTx->CR3, USART_CR3_OVRDIS); } /** * @brief Indicate if Overrun detection is enabled * @rmtoll CR3 OVRDIS LL_LPUART_IsEnabledOverrunDetect * @param LPUARTx LPUART Instance * @retval State of bit (1 or 0). */ __STATIC_INLINE uint32_t LL_LPUART_IsEnabledOverrunDetect(const USART_TypeDef *LPUARTx) { return ((READ_BIT(LPUARTx->CR3, USART_CR3_OVRDIS) != USART_CR3_OVRDIS) ? 1UL : 0UL); } /** * @brief Select event type for Wake UP Interrupt Flag (WUS[1:0] bits) * @rmtoll CR3 WUS LL_LPUART_SetWKUPType * @param LPUARTx LPUART Instance * @param Type This parameter can be one of the following values: * @arg @ref LL_LPUART_WAKEUP_ON_ADDRESS * @arg @ref LL_LPUART_WAKEUP_ON_STARTBIT * @arg @ref LL_LPUART_WAKEUP_ON_RXNE * @retval None */ __STATIC_INLINE void LL_LPUART_SetWKUPType(USART_TypeDef *LPUARTx, uint32_t Type) { MODIFY_REG(LPUARTx->CR3, USART_CR3_WUS, Type); } /** * @brief Return event type for Wake UP Interrupt Flag (WUS[1:0] bits) * @rmtoll CR3 WUS LL_LPUART_GetWKUPType * @param LPUARTx LPUART Instance * @retval Returned value can be one of the following values: * @arg @ref LL_LPUART_WAKEUP_ON_ADDRESS * @arg @ref LL_LPUART_WAKEUP_ON_STARTBIT * @arg @ref LL_LPUART_WAKEUP_ON_RXNE */ __STATIC_INLINE uint32_t LL_LPUART_GetWKUPType(const USART_TypeDef *LPUARTx) { return (uint32_t)(READ_BIT(LPUARTx->CR3, USART_CR3_WUS)); } /** * @brief Configure LPUART BRR register for achieving expected Baud Rate value. * * @note Compute and set LPUARTDIV value in BRR Register (full BRR content) * according to used Peripheral Clock and expected Baud Rate values * @note Peripheral clock and Baud Rate values provided as function parameters should be valid * (Baud rate value != 0). * @note Provided that LPUARTx_BRR must be > = 0x300 and LPUART_BRR is 20-bit, * a care should be taken when generating high baud rates using high PeriphClk * values. PeriphClk must be in the range [3 x BaudRate, 4096 x BaudRate]. * @rmtoll BRR BRR LL_LPUART_SetBaudRate * @param LPUARTx LPUART Instance * @param PeriphClk Peripheral Clock @if USART_PRESC_PRESCALER * @param PrescalerValue This parameter can be one of the following values: * @arg @ref LL_LPUART_PRESCALER_DIV1 * @arg @ref LL_LPUART_PRESCALER_DIV2 * @arg @ref LL_LPUART_PRESCALER_DIV4 * @arg @ref LL_LPUART_PRESCALER_DIV6 * @arg @ref LL_LPUART_PRESCALER_DIV8 * @arg @ref LL_LPUART_PRESCALER_DIV10 * @arg @ref LL_LPUART_PRESCALER_DIV12 * @arg @ref LL_LPUART_PRESCALER_DIV16 * @arg @ref LL_LPUART_PRESCALER_DIV32 * @arg @ref LL_LPUART_PRESCALER_DIV64 * @arg @ref LL_LPUART_PRESCALER_DIV128 * @arg @ref LL_LPUART_PRESCALER_DIV256 @endif * @param BaudRate Baud Rate * @retval None */ #if defined(USART_PRESC_PRESCALER) __STATIC_INLINE void LL_LPUART_SetBaudRate(USART_TypeDef *LPUARTx, uint32_t PeriphClk, uint32_t PrescalerValue, uint32_t BaudRate) #else __STATIC_INLINE void LL_LPUART_SetBaudRate(USART_TypeDef *LPUARTx, uint32_t PeriphClk, uint32_t BaudRate) #endif /* USART_PRESC_PRESCALER */ { #if defined(USART_PRESC_PRESCALER) if (BaudRate != 0U) { LPUARTx->BRR = __LL_LPUART_DIV(PeriphClk, PrescalerValue, BaudRate); } #else if (BaudRate != 0U) { LPUARTx->BRR = __LL_LPUART_DIV(PeriphClk, BaudRate); } #endif /* USART_PRESC_PRESCALER */ } /** * @brief Return current Baud Rate value, according to LPUARTDIV present in BRR register * (full BRR content), and to used Peripheral Clock values * @note In case of non-initialized or invalid value stored in BRR register, value 0 will be returned. * @rmtoll BRR BRR LL_LPUART_GetBaudRate * @param LPUARTx LPUART Instance * @param PeriphClk Peripheral Clock @if USART_PRESC_PRESCALER * @param PrescalerValue This parameter can be one of the following values: * @arg @ref LL_LPUART_PRESCALER_DIV1 * @arg @ref LL_LPUART_PRESCALER_DIV2 * @arg @ref LL_LPUART_PRESCALER_DIV4 * @arg @ref LL_LPUART_PRESCALER_DIV6 * @arg @ref LL_LPUART_PRESCALER_DIV8 * @arg @ref LL_LPUART_PRESCALER_DIV10 * @arg @ref LL_LPUART_PRESCALER_DIV12 * @arg @ref LL_LPUART_PRESCALER_DIV16 * @arg @ref LL_LPUART_PRESCALER_DIV32 * @arg @ref LL_LPUART_PRESCALER_DIV64 * @arg @ref LL_LPUART_PRESCALER_DIV128 * @arg @ref LL_LPUART_PRESCALER_DIV256 @endif * @retval Baud Rate */ #if defined(USART_PRESC_PRESCALER) __STATIC_INLINE uint32_t LL_LPUART_GetBaudRate(const USART_TypeDef *LPUARTx, uint32_t PeriphClk, uint32_t PrescalerValue) #else __STATIC_INLINE uint32_t LL_LPUART_GetBaudRate(const USART_TypeDef *LPUARTx, uint32_t PeriphClk) #endif /* USART_PRESC_PRESCALER */ { uint32_t lpuartdiv; uint32_t brrresult; #if defined(USART_PRESC_PRESCALER) uint32_t periphclkpresc = (uint32_t)(PeriphClk / (LPUART_PRESCALER_TAB[(uint16_t)PrescalerValue])); #endif /* USART_PRESC_PRESCALER */ lpuartdiv = LPUARTx->BRR & LPUART_BRR_MASK; if (lpuartdiv >= LPUART_BRR_MIN_VALUE) { #if defined(USART_PRESC_PRESCALER) brrresult = (uint32_t)(((uint64_t)(periphclkpresc) * LPUART_LPUARTDIV_FREQ_MUL) / lpuartdiv); #else brrresult = (uint32_t)(((uint64_t)(PeriphClk) * LPUART_LPUARTDIV_FREQ_MUL) / lpuartdiv); #endif /* USART_PRESC_PRESCALER */ } else { brrresult = 0x0UL; } return (brrresult); } /** * @} */ /** @defgroup LPUART_LL_EF_Configuration_HalfDuplex Configuration functions related to Half Duplex feature * @{ */ /** * @brief Enable Single Wire Half-Duplex mode * @rmtoll CR3 HDSEL LL_LPUART_EnableHalfDuplex * @param LPUARTx LPUART Instance * @retval None */ __STATIC_INLINE void LL_LPUART_EnableHalfDuplex(USART_TypeDef *LPUARTx) { SET_BIT(LPUARTx->CR3, USART_CR3_HDSEL); } /** * @brief Disable Single Wire Half-Duplex mode * @rmtoll CR3 HDSEL LL_LPUART_DisableHalfDuplex * @param LPUARTx LPUART Instance * @retval None */ __STATIC_INLINE void LL_LPUART_DisableHalfDuplex(USART_TypeDef *LPUARTx) { CLEAR_BIT(LPUARTx->CR3, USART_CR3_HDSEL); } /** * @brief Indicate if Single Wire Half-Duplex mode is enabled * @rmtoll CR3 HDSEL LL_LPUART_IsEnabledHalfDuplex * @param LPUARTx LPUART Instance * @retval State of bit (1 or 0). */ __STATIC_INLINE uint32_t LL_LPUART_IsEnabledHalfDuplex(const USART_TypeDef *LPUARTx) { return ((READ_BIT(LPUARTx->CR3, USART_CR3_HDSEL) == (USART_CR3_HDSEL)) ? 1UL : 0UL); } /** * @} */ /** @defgroup LPUART_LL_EF_Configuration_DE Configuration functions related to Driver Enable feature * @{ */ /** * @brief Set DEDT (Driver Enable De-Assertion Time), Time value expressed on 5 bits ([4:0] bits). * @rmtoll CR1 DEDT LL_LPUART_SetDEDeassertionTime * @param LPUARTx LPUART Instance * @param Time Value between Min_Data=0 and Max_Data=31 * @retval None */ __STATIC_INLINE void LL_LPUART_SetDEDeassertionTime(USART_TypeDef *LPUARTx, uint32_t Time) { MODIFY_REG(LPUARTx->CR1, USART_CR1_DEDT, Time << USART_CR1_DEDT_Pos); } /** * @brief Return DEDT (Driver Enable De-Assertion Time) * @rmtoll CR1 DEDT LL_LPUART_GetDEDeassertionTime * @param LPUARTx LPUART Instance * @retval Time value expressed on 5 bits ([4:0] bits) : c */ __STATIC_INLINE uint32_t LL_LPUART_GetDEDeassertionTime(const USART_TypeDef *LPUARTx) { return (uint32_t)(READ_BIT(LPUARTx->CR1, USART_CR1_DEDT) >> USART_CR1_DEDT_Pos); } /** * @brief Set DEAT (Driver Enable Assertion Time), Time value expressed on 5 bits ([4:0] bits). * @rmtoll CR1 DEAT LL_LPUART_SetDEAssertionTime * @param LPUARTx LPUART Instance * @param Time Value between Min_Data=0 and Max_Data=31 * @retval None */ __STATIC_INLINE void LL_LPUART_SetDEAssertionTime(USART_TypeDef *LPUARTx, uint32_t Time) { MODIFY_REG(LPUARTx->CR1, USART_CR1_DEAT, Time << USART_CR1_DEAT_Pos); } /** * @brief Return DEAT (Driver Enable Assertion Time) * @rmtoll CR1 DEAT LL_LPUART_GetDEAssertionTime * @param LPUARTx LPUART Instance * @retval Time value expressed on 5 bits ([4:0] bits) : Time Value between Min_Data=0 and Max_Data=31 */ __STATIC_INLINE uint32_t LL_LPUART_GetDEAssertionTime(const USART_TypeDef *LPUARTx) { return (uint32_t)(READ_BIT(LPUARTx->CR1, USART_CR1_DEAT) >> USART_CR1_DEAT_Pos); } /** * @brief Enable Driver Enable (DE) Mode * @rmtoll CR3 DEM LL_LPUART_EnableDEMode * @param LPUARTx LPUART Instance * @retval None */ __STATIC_INLINE void LL_LPUART_EnableDEMode(USART_TypeDef *LPUARTx) { SET_BIT(LPUARTx->CR3, USART_CR3_DEM); } /** * @brief Disable Driver Enable (DE) Mode * @rmtoll CR3 DEM LL_LPUART_DisableDEMode * @param LPUARTx LPUART Instance * @retval None */ __STATIC_INLINE void LL_LPUART_DisableDEMode(USART_TypeDef *LPUARTx) { CLEAR_BIT(LPUARTx->CR3, USART_CR3_DEM); } /** * @brief Indicate if Driver Enable (DE) Mode is enabled * @rmtoll CR3 DEM LL_LPUART_IsEnabledDEMode * @param LPUARTx LPUART Instance * @retval State of bit (1 or 0). */ __STATIC_INLINE uint32_t LL_LPUART_IsEnabledDEMode(const USART_TypeDef *LPUARTx) { return ((READ_BIT(LPUARTx->CR3, USART_CR3_DEM) == (USART_CR3_DEM)) ? 1UL : 0UL); } /** * @brief Select Driver Enable Polarity * @rmtoll CR3 DEP LL_LPUART_SetDESignalPolarity * @param LPUARTx LPUART Instance * @param Polarity This parameter can be one of the following values: * @arg @ref LL_LPUART_DE_POLARITY_HIGH * @arg @ref LL_LPUART_DE_POLARITY_LOW * @retval None */ __STATIC_INLINE void LL_LPUART_SetDESignalPolarity(USART_TypeDef *LPUARTx, uint32_t Polarity) { MODIFY_REG(LPUARTx->CR3, USART_CR3_DEP, Polarity); } /** * @brief Return Driver Enable Polarity * @rmtoll CR3 DEP LL_LPUART_GetDESignalPolarity * @param LPUARTx LPUART Instance * @retval Returned value can be one of the following values: * @arg @ref LL_LPUART_DE_POLARITY_HIGH * @arg @ref LL_LPUART_DE_POLARITY_LOW */ __STATIC_INLINE uint32_t LL_LPUART_GetDESignalPolarity(const USART_TypeDef *LPUARTx) { return (uint32_t)(READ_BIT(LPUARTx->CR3, USART_CR3_DEP)); } /** * @} */ /** @defgroup LPUART_LL_EF_FLAG_Management FLAG_Management * @{ */ /** * @brief Check if the LPUART Parity Error Flag is set or not * @rmtoll ISR PE LL_LPUART_IsActiveFlag_PE * @param LPUARTx LPUART Instance * @retval State of bit (1 or 0). */ __STATIC_INLINE uint32_t LL_LPUART_IsActiveFlag_PE(const USART_TypeDef *LPUARTx) { return ((READ_BIT(LPUARTx->ISR, USART_ISR_PE) == (USART_ISR_PE)) ? 1UL : 0UL); } /** * @brief Check if the LPUART Framing Error Flag is set or not * @rmtoll ISR FE LL_LPUART_IsActiveFlag_FE * @param LPUARTx LPUART Instance * @retval State of bit (1 or 0). */ __STATIC_INLINE uint32_t LL_LPUART_IsActiveFlag_FE(const USART_TypeDef *LPUARTx) { return ((READ_BIT(LPUARTx->ISR, USART_ISR_FE) == (USART_ISR_FE)) ? 1UL : 0UL); } /** * @brief Check if the LPUART Noise error detected Flag is set or not * @rmtoll ISR NE LL_LPUART_IsActiveFlag_NE * @param LPUARTx LPUART Instance * @retval State of bit (1 or 0). */ __STATIC_INLINE uint32_t LL_LPUART_IsActiveFlag_NE(const USART_TypeDef *LPUARTx) { return ((READ_BIT(LPUARTx->ISR, USART_ISR_NE) == (USART_ISR_NE)) ? 1UL : 0UL); } /** * @brief Check if the LPUART OverRun Error Flag is set or not * @rmtoll ISR ORE LL_LPUART_IsActiveFlag_ORE * @param LPUARTx LPUART Instance * @retval State of bit (1 or 0). */ __STATIC_INLINE uint32_t LL_LPUART_IsActiveFlag_ORE(const USART_TypeDef *LPUARTx) { return ((READ_BIT(LPUARTx->ISR, USART_ISR_ORE) == (USART_ISR_ORE)) ? 1UL : 0UL); } /** * @brief Check if the LPUART IDLE line detected Flag is set or not * @rmtoll ISR IDLE LL_LPUART_IsActiveFlag_IDLE * @param LPUARTx LPUART Instance * @retval State of bit (1 or 0). */ __STATIC_INLINE uint32_t LL_LPUART_IsActiveFlag_IDLE(const USART_TypeDef *LPUARTx) { return ((READ_BIT(LPUARTx->ISR, USART_ISR_IDLE) == (USART_ISR_IDLE)) ? 1UL : 0UL); } #if defined(USART_CR1_FIFOEN) #define LL_LPUART_IsActiveFlag_RXNE LL_LPUART_IsActiveFlag_RXNE_RXFNE /* Redefinition for legacy purpose */ /** * @brief Check if the LPUART Read Data Register or LPUART RX FIFO Not Empty Flag is set or not * @rmtoll ISR RXNE_RXFNE LL_LPUART_IsActiveFlag_RXNE_RXFNE * @param LPUARTx LPUART Instance * @retval State of bit (1 or 0). */ __STATIC_INLINE uint32_t LL_LPUART_IsActiveFlag_RXNE_RXFNE(const USART_TypeDef *LPUARTx) { return ((READ_BIT(LPUARTx->ISR, USART_ISR_RXNE_RXFNE) == (USART_ISR_RXNE_RXFNE)) ? 1UL : 0UL); } #else /** * @brief Check if the LPUART Read Data Register Not Empty Flag is set or not * @rmtoll ISR RXNE LL_LPUART_IsActiveFlag_RXNE * @param LPUARTx LPUART Instance * @retval State of bit (1 or 0). */ __STATIC_INLINE uint32_t LL_LPUART_IsActiveFlag_RXNE(const USART_TypeDef *LPUARTx) { return ((READ_BIT(LPUARTx->ISR, USART_ISR_RXNE) == (USART_ISR_RXNE)) ? 1UL : 0UL); } #endif /* USART_CR1_FIFOEN */ /** * @brief Check if the LPUART Transmission Complete Flag is set or not * @rmtoll ISR TC LL_LPUART_IsActiveFlag_TC * @param LPUARTx LPUART Instance * @retval State of bit (1 or 0). */ __STATIC_INLINE uint32_t LL_LPUART_IsActiveFlag_TC(const USART_TypeDef *LPUARTx) { return ((READ_BIT(LPUARTx->ISR, USART_ISR_TC) == (USART_ISR_TC)) ? 1UL : 0UL); } #if defined(USART_CR1_FIFOEN) #define LL_LPUART_IsActiveFlag_TXE LL_LPUART_IsActiveFlag_TXE_TXFNF /* Redefinition for legacy purpose */ /** * @brief Check if the LPUART Transmit Data Register Empty or LPUART TX FIFO Not Full Flag is set or not * @rmtoll ISR TXE_TXFNF LL_LPUART_IsActiveFlag_TXE_TXFNF * @param LPUARTx LPUART Instance * @retval State of bit (1 or 0). */ __STATIC_INLINE uint32_t LL_LPUART_IsActiveFlag_TXE_TXFNF(const USART_TypeDef *LPUARTx) { return ((READ_BIT(LPUARTx->ISR, USART_ISR_TXE_TXFNF) == (USART_ISR_TXE_TXFNF)) ? 1UL : 0UL); } #else /** * @brief Check if the LPUART Transmit Data Register Empty Flag is set or not * @rmtoll ISR TXE LL_LPUART_IsActiveFlag_TXE * @param LPUARTx LPUART Instance * @retval State of bit (1 or 0). */ __STATIC_INLINE uint32_t LL_LPUART_IsActiveFlag_TXE(const USART_TypeDef *LPUARTx) { return ((READ_BIT(LPUARTx->ISR, USART_ISR_TXE) == (USART_ISR_TXE)) ? 1UL : 0UL); } #endif /* USART_CR1_FIFOEN */ /** * @brief Check if the LPUART CTS interrupt Flag is set or not * @rmtoll ISR CTSIF LL_LPUART_IsActiveFlag_nCTS * @param LPUARTx LPUART Instance * @retval State of bit (1 or 0). */ __STATIC_INLINE uint32_t LL_LPUART_IsActiveFlag_nCTS(const USART_TypeDef *LPUARTx) { return ((READ_BIT(LPUARTx->ISR, USART_ISR_CTSIF) == (USART_ISR_CTSIF)) ? 1UL : 0UL); } /** * @brief Check if the LPUART CTS Flag is set or not * @rmtoll ISR CTS LL_LPUART_IsActiveFlag_CTS * @param LPUARTx LPUART Instance * @retval State of bit (1 or 0). */ __STATIC_INLINE uint32_t LL_LPUART_IsActiveFlag_CTS(const USART_TypeDef *LPUARTx) { return ((READ_BIT(LPUARTx->ISR, USART_ISR_CTS) == (USART_ISR_CTS)) ? 1UL : 0UL); } /** * @brief Check if the LPUART Busy Flag is set or not * @rmtoll ISR BUSY LL_LPUART_IsActiveFlag_BUSY * @param LPUARTx LPUART Instance * @retval State of bit (1 or 0). */ __STATIC_INLINE uint32_t LL_LPUART_IsActiveFlag_BUSY(const USART_TypeDef *LPUARTx) { return ((READ_BIT(LPUARTx->ISR, USART_ISR_BUSY) == (USART_ISR_BUSY)) ? 1UL : 0UL); } /** * @brief Check if the LPUART Character Match Flag is set or not * @rmtoll ISR CMF LL_LPUART_IsActiveFlag_CM * @param LPUARTx LPUART Instance * @retval State of bit (1 or 0). */ __STATIC_INLINE uint32_t LL_LPUART_IsActiveFlag_CM(const USART_TypeDef *LPUARTx) { return ((READ_BIT(LPUARTx->ISR, USART_ISR_CMF) == (USART_ISR_CMF)) ? 1UL : 0UL); } /** * @brief Check if the LPUART Send Break Flag is set or not * @rmtoll ISR SBKF LL_LPUART_IsActiveFlag_SBK * @param LPUARTx LPUART Instance * @retval State of bit (1 or 0). */ __STATIC_INLINE uint32_t LL_LPUART_IsActiveFlag_SBK(const USART_TypeDef *LPUARTx) { return ((READ_BIT(LPUARTx->ISR, USART_ISR_SBKF) == (USART_ISR_SBKF)) ? 1UL : 0UL); } /** * @brief Check if the LPUART Receive Wake Up from mute mode Flag is set or not * @rmtoll ISR RWU LL_LPUART_IsActiveFlag_RWU * @param LPUARTx LPUART Instance * @retval State of bit (1 or 0). */ __STATIC_INLINE uint32_t LL_LPUART_IsActiveFlag_RWU(const USART_TypeDef *LPUARTx) { return ((READ_BIT(LPUARTx->ISR, USART_ISR_RWU) == (USART_ISR_RWU)) ? 1UL : 0UL); } /** * @brief Check if the LPUART Wake Up from stop mode Flag is set or not * @rmtoll ISR WUF LL_LPUART_IsActiveFlag_WKUP * @param LPUARTx LPUART Instance * @retval State of bit (1 or 0). */ __STATIC_INLINE uint32_t LL_LPUART_IsActiveFlag_WKUP(const USART_TypeDef *LPUARTx) { return ((READ_BIT(LPUARTx->ISR, USART_ISR_WUF) == (USART_ISR_WUF)) ? 1UL : 0UL); } /** * @brief Check if the LPUART Transmit Enable Acknowledge Flag is set or not * @rmtoll ISR TEACK LL_LPUART_IsActiveFlag_TEACK * @param LPUARTx LPUART Instance * @retval State of bit (1 or 0). */ __STATIC_INLINE uint32_t LL_LPUART_IsActiveFlag_TEACK(const USART_TypeDef *LPUARTx) { return ((READ_BIT(LPUARTx->ISR, USART_ISR_TEACK) == (USART_ISR_TEACK)) ? 1UL : 0UL); } /** * @brief Check if the LPUART Receive Enable Acknowledge Flag is set or not * @rmtoll ISR REACK LL_LPUART_IsActiveFlag_REACK * @param LPUARTx LPUART Instance * @retval State of bit (1 or 0). */ __STATIC_INLINE uint32_t LL_LPUART_IsActiveFlag_REACK(const USART_TypeDef *LPUARTx) { return ((READ_BIT(LPUARTx->ISR, USART_ISR_REACK) == (USART_ISR_REACK)) ? 1UL : 0UL); } #if defined(USART_CR1_FIFOEN) /** * @brief Check if the LPUART TX FIFO Empty Flag is set or not * @rmtoll ISR TXFE LL_LPUART_IsActiveFlag_TXFE * @param LPUARTx LPUART Instance * @retval State of bit (1 or 0). */ __STATIC_INLINE uint32_t LL_LPUART_IsActiveFlag_TXFE(const USART_TypeDef *LPUARTx) { return ((READ_BIT(LPUARTx->ISR, USART_ISR_TXFE) == (USART_ISR_TXFE)) ? 1UL : 0UL); } /** * @brief Check if the LPUART RX FIFO Full Flag is set or not * @rmtoll ISR RXFF LL_LPUART_IsActiveFlag_RXFF * @param LPUARTx LPUART Instance * @retval State of bit (1 or 0). */ __STATIC_INLINE uint32_t LL_LPUART_IsActiveFlag_RXFF(const USART_TypeDef *LPUARTx) { return ((READ_BIT(LPUARTx->ISR, USART_ISR_RXFF) == (USART_ISR_RXFF)) ? 1UL : 0UL); } /** * @brief Check if the LPUART TX FIFO Threshold Flag is set or not * @rmtoll ISR TXFT LL_LPUART_IsActiveFlag_TXFT * @param LPUARTx LPUART Instance * @retval State of bit (1 or 0). */ __STATIC_INLINE uint32_t LL_LPUART_IsActiveFlag_TXFT(const USART_TypeDef *LPUARTx) { return ((READ_BIT(LPUARTx->ISR, USART_ISR_TXFT) == (USART_ISR_TXFT)) ? 1UL : 0UL); } /** * @brief Check if the LPUART RX FIFO Threshold Flag is set or not * @rmtoll ISR RXFT LL_LPUART_IsActiveFlag_RXFT * @param LPUARTx LPUART Instance * @retval State of bit (1 or 0). */ __STATIC_INLINE uint32_t LL_LPUART_IsActiveFlag_RXFT(const USART_TypeDef *LPUARTx) { return ((READ_BIT(LPUARTx->ISR, USART_ISR_RXFT) == (USART_ISR_RXFT)) ? 1UL : 0UL); } #endif /* USART_CR1_FIFOEN */ /** * @brief Clear Parity Error Flag * @rmtoll ICR PECF LL_LPUART_ClearFlag_PE * @param LPUARTx LPUART Instance * @retval None */ __STATIC_INLINE void LL_LPUART_ClearFlag_PE(USART_TypeDef *LPUARTx) { WRITE_REG(LPUARTx->ICR, USART_ICR_PECF); } /** * @brief Clear Framing Error Flag * @rmtoll ICR FECF LL_LPUART_ClearFlag_FE * @param LPUARTx LPUART Instance * @retval None */ __STATIC_INLINE void LL_LPUART_ClearFlag_FE(USART_TypeDef *LPUARTx) { WRITE_REG(LPUARTx->ICR, USART_ICR_FECF); } /** * @brief Clear Noise detected Flag * @rmtoll ICR NECF LL_LPUART_ClearFlag_NE * @param LPUARTx LPUART Instance * @retval None */ __STATIC_INLINE void LL_LPUART_ClearFlag_NE(USART_TypeDef *LPUARTx) { WRITE_REG(LPUARTx->ICR, USART_ICR_NECF); } /** * @brief Clear OverRun Error Flag * @rmtoll ICR ORECF LL_LPUART_ClearFlag_ORE * @param LPUARTx LPUART Instance * @retval None */ __STATIC_INLINE void LL_LPUART_ClearFlag_ORE(USART_TypeDef *LPUARTx) { WRITE_REG(LPUARTx->ICR, USART_ICR_ORECF); } /** * @brief Clear IDLE line detected Flag * @rmtoll ICR IDLECF LL_LPUART_ClearFlag_IDLE * @param LPUARTx LPUART Instance * @retval None */ __STATIC_INLINE void LL_LPUART_ClearFlag_IDLE(USART_TypeDef *LPUARTx) { WRITE_REG(LPUARTx->ICR, USART_ICR_IDLECF); } /** * @brief Clear Transmission Complete Flag * @rmtoll ICR TCCF LL_LPUART_ClearFlag_TC * @param LPUARTx LPUART Instance * @retval None */ __STATIC_INLINE void LL_LPUART_ClearFlag_TC(USART_TypeDef *LPUARTx) { WRITE_REG(LPUARTx->ICR, USART_ICR_TCCF); } /** * @brief Clear CTS Interrupt Flag * @rmtoll ICR CTSCF LL_LPUART_ClearFlag_nCTS * @param LPUARTx LPUART Instance * @retval None */ __STATIC_INLINE void LL_LPUART_ClearFlag_nCTS(USART_TypeDef *LPUARTx) { WRITE_REG(LPUARTx->ICR, USART_ICR_CTSCF); } /** * @brief Clear Character Match Flag * @rmtoll ICR CMCF LL_LPUART_ClearFlag_CM * @param LPUARTx LPUART Instance * @retval None */ __STATIC_INLINE void LL_LPUART_ClearFlag_CM(USART_TypeDef *LPUARTx) { WRITE_REG(LPUARTx->ICR, USART_ICR_CMCF); } /** * @brief Clear Wake Up from stop mode Flag * @rmtoll ICR WUCF LL_LPUART_ClearFlag_WKUP * @param LPUARTx LPUART Instance * @retval None */ __STATIC_INLINE void LL_LPUART_ClearFlag_WKUP(USART_TypeDef *LPUARTx) { WRITE_REG(LPUARTx->ICR, USART_ICR_WUCF); } /** * @} */ /** @defgroup LPUART_LL_EF_IT_Management IT_Management * @{ */ /** * @brief Enable IDLE Interrupt * @rmtoll CR1 IDLEIE LL_LPUART_EnableIT_IDLE * @param LPUARTx LPUART Instance * @retval None */ __STATIC_INLINE void LL_LPUART_EnableIT_IDLE(USART_TypeDef *LPUARTx) { ATOMIC_SET_BIT(LPUARTx->CR1, USART_CR1_IDLEIE); } #if defined(USART_CR1_FIFOEN) #define LL_LPUART_EnableIT_RXNE LL_LPUART_EnableIT_RXNE_RXFNE /* Redefinition for legacy purpose */ /** * @brief Enable RX Not Empty and RX FIFO Not Empty Interrupt * @rmtoll CR1 RXNEIE_RXFNEIE LL_LPUART_EnableIT_RXNE_RXFNE * @param LPUARTx LPUART Instance * @retval None */ __STATIC_INLINE void LL_LPUART_EnableIT_RXNE_RXFNE(USART_TypeDef *LPUARTx) { ATOMIC_SET_BIT(LPUARTx->CR1, USART_CR1_RXNEIE_RXFNEIE); } #else /** * @brief Enable RX Not Empty Interrupt * @rmtoll CR1 RXNEIE LL_LPUART_EnableIT_RXNE * @param LPUARTx LPUART Instance * @retval None */ __STATIC_INLINE void LL_LPUART_EnableIT_RXNE(USART_TypeDef *LPUARTx) { ATOMIC_SET_BIT(LPUARTx->CR1, USART_CR1_RXNEIE); } #endif /* USART_CR1_FIFOEN */ /** * @brief Enable Transmission Complete Interrupt * @rmtoll CR1 TCIE LL_LPUART_EnableIT_TC * @param LPUARTx LPUART Instance * @retval None */ __STATIC_INLINE void LL_LPUART_EnableIT_TC(USART_TypeDef *LPUARTx) { ATOMIC_SET_BIT(LPUARTx->CR1, USART_CR1_TCIE); } #if defined(USART_CR1_FIFOEN) #define LL_LPUART_EnableIT_TXE LL_LPUART_EnableIT_TXE_TXFNF /* Redefinition for legacy purpose */ /** * @brief Enable TX Empty and TX FIFO Not Full Interrupt * @rmtoll CR1 TXEIE_TXFNFIE LL_LPUART_EnableIT_TXE_TXFNF * @param LPUARTx LPUART Instance * @retval None */ __STATIC_INLINE void LL_LPUART_EnableIT_TXE_TXFNF(USART_TypeDef *LPUARTx) { ATOMIC_SET_BIT(LPUARTx->CR1, USART_CR1_TXEIE_TXFNFIE); } #else /** * @brief Enable TX Empty Interrupt * @rmtoll CR1 TXEIE LL_LPUART_EnableIT_TXE * @param LPUARTx LPUART Instance * @retval None */ __STATIC_INLINE void LL_LPUART_EnableIT_TXE(USART_TypeDef *LPUARTx) { ATOMIC_SET_BIT(LPUARTx->CR1, USART_CR1_TXEIE); } #endif /* USART_CR1_FIFOEN */ /** * @brief Enable Parity Error Interrupt * @rmtoll CR1 PEIE LL_LPUART_EnableIT_PE * @param LPUARTx LPUART Instance * @retval None */ __STATIC_INLINE void LL_LPUART_EnableIT_PE(USART_TypeDef *LPUARTx) { ATOMIC_SET_BIT(LPUARTx->CR1, USART_CR1_PEIE); } /** * @brief Enable Character Match Interrupt * @rmtoll CR1 CMIE LL_LPUART_EnableIT_CM * @param LPUARTx LPUART Instance * @retval None */ __STATIC_INLINE void LL_LPUART_EnableIT_CM(USART_TypeDef *LPUARTx) { ATOMIC_SET_BIT(LPUARTx->CR1, USART_CR1_CMIE); } #if defined(USART_CR1_FIFOEN) /** * @brief Enable TX FIFO Empty Interrupt * @rmtoll CR1 TXFEIE LL_LPUART_EnableIT_TXFE * @param LPUARTx LPUART Instance * @retval None */ __STATIC_INLINE void LL_LPUART_EnableIT_TXFE(USART_TypeDef *LPUARTx) { ATOMIC_SET_BIT(LPUARTx->CR1, USART_CR1_TXFEIE); } /** * @brief Enable RX FIFO Full Interrupt * @rmtoll CR1 RXFFIE LL_LPUART_EnableIT_RXFF * @param LPUARTx LPUART Instance * @retval None */ __STATIC_INLINE void LL_LPUART_EnableIT_RXFF(USART_TypeDef *LPUARTx) { ATOMIC_SET_BIT(LPUARTx->CR1, USART_CR1_RXFFIE); } #endif /* USART_CR1_FIFOEN */ /** * @brief Enable Error Interrupt * @note When set, Error Interrupt Enable Bit is enabling interrupt generation in case of a framing * error, overrun error or noise flag (FE=1 or ORE=1 or NF=1 in the LPUARTx_ISR register). * - 0: Interrupt is inhibited * - 1: An interrupt is generated when FE=1 or ORE=1 or NF=1 in the LPUARTx_ISR register. * @rmtoll CR3 EIE LL_LPUART_EnableIT_ERROR * @param LPUARTx LPUART Instance * @retval None */ __STATIC_INLINE void LL_LPUART_EnableIT_ERROR(USART_TypeDef *LPUARTx) { ATOMIC_SET_BIT(LPUARTx->CR3, USART_CR3_EIE); } /** * @brief Enable CTS Interrupt * @rmtoll CR3 CTSIE LL_LPUART_EnableIT_CTS * @param LPUARTx LPUART Instance * @retval None */ __STATIC_INLINE void LL_LPUART_EnableIT_CTS(USART_TypeDef *LPUARTx) { ATOMIC_SET_BIT(LPUARTx->CR3, USART_CR3_CTSIE); } /** * @brief Enable Wake Up from Stop Mode Interrupt * @rmtoll CR3 WUFIE LL_LPUART_EnableIT_WKUP * @param LPUARTx LPUART Instance * @retval None */ __STATIC_INLINE void LL_LPUART_EnableIT_WKUP(USART_TypeDef *LPUARTx) { ATOMIC_SET_BIT(LPUARTx->CR3, USART_CR3_WUFIE); } #if defined(USART_CR1_FIFOEN) /** * @brief Enable TX FIFO Threshold Interrupt * @rmtoll CR3 TXFTIE LL_LPUART_EnableIT_TXFT * @param LPUARTx LPUART Instance * @retval None */ __STATIC_INLINE void LL_LPUART_EnableIT_TXFT(USART_TypeDef *LPUARTx) { ATOMIC_SET_BIT(LPUARTx->CR3, USART_CR3_TXFTIE); } /** * @brief Enable RX FIFO Threshold Interrupt * @rmtoll CR3 RXFTIE LL_LPUART_EnableIT_RXFT * @param LPUARTx LPUART Instance * @retval None */ __STATIC_INLINE void LL_LPUART_EnableIT_RXFT(USART_TypeDef *LPUARTx) { ATOMIC_SET_BIT(LPUARTx->CR3, USART_CR3_RXFTIE); } #endif /* USART_CR1_FIFOEN */ /** * @brief Disable IDLE Interrupt * @rmtoll CR1 IDLEIE LL_LPUART_DisableIT_IDLE * @param LPUARTx LPUART Instance * @retval None */ __STATIC_INLINE void LL_LPUART_DisableIT_IDLE(USART_TypeDef *LPUARTx) { ATOMIC_CLEAR_BIT(LPUARTx->CR1, USART_CR1_IDLEIE); } #if defined(USART_CR1_FIFOEN) #define LL_LPUART_DisableIT_RXNE LL_LPUART_DisableIT_RXNE_RXFNE /* Redefinition for legacy purpose */ /** * @brief Disable RX Not Empty and RX FIFO Not Empty Interrupt * @rmtoll CR1 RXNEIE_RXFNEIE LL_LPUART_DisableIT_RXNE_RXFNE * @param LPUARTx LPUART Instance * @retval None */ __STATIC_INLINE void LL_LPUART_DisableIT_RXNE_RXFNE(USART_TypeDef *LPUARTx) { ATOMIC_CLEAR_BIT(LPUARTx->CR1, USART_CR1_RXNEIE_RXFNEIE); } #else /** * @brief Disable RX Not Empty Interrupt * @rmtoll CR1 RXNEIE LL_LPUART_DisableIT_RXNE * @param LPUARTx LPUART Instance * @retval None */ __STATIC_INLINE void LL_LPUART_DisableIT_RXNE(USART_TypeDef *LPUARTx) { ATOMIC_CLEAR_BIT(LPUARTx->CR1, USART_CR1_RXNEIE); } #endif /* USART_CR1_FIFOEN */ /** * @brief Disable Transmission Complete Interrupt * @rmtoll CR1 TCIE LL_LPUART_DisableIT_TC * @param LPUARTx LPUART Instance * @retval None */ __STATIC_INLINE void LL_LPUART_DisableIT_TC(USART_TypeDef *LPUARTx) { ATOMIC_CLEAR_BIT(LPUARTx->CR1, USART_CR1_TCIE); } #if defined(USART_CR1_FIFOEN) #define LL_LPUART_DisableIT_TXE LL_LPUART_DisableIT_TXE_TXFNF /* Redefinition for legacy purpose */ /** * @brief Disable TX Empty and TX FIFO Not Full Interrupt * @rmtoll CR1 TXEIE_TXFNFIE LL_LPUART_DisableIT_TXE_TXFNF * @param LPUARTx LPUART Instance * @retval None */ __STATIC_INLINE void LL_LPUART_DisableIT_TXE_TXFNF(USART_TypeDef *LPUARTx) { ATOMIC_CLEAR_BIT(LPUARTx->CR1, USART_CR1_TXEIE_TXFNFIE); } #else /** * @brief Disable TX Empty Interrupt * @rmtoll CR1 TXEIE LL_LPUART_DisableIT_TXE * @param LPUARTx LPUART Instance * @retval None */ __STATIC_INLINE void LL_LPUART_DisableIT_TXE(USART_TypeDef *LPUARTx) { ATOMIC_CLEAR_BIT(LPUARTx->CR1, USART_CR1_TXEIE); } #endif /* USART_CR1_FIFOEN */ /** * @brief Disable Parity Error Interrupt * @rmtoll CR1 PEIE LL_LPUART_DisableIT_PE * @param LPUARTx LPUART Instance * @retval None */ __STATIC_INLINE void LL_LPUART_DisableIT_PE(USART_TypeDef *LPUARTx) { ATOMIC_CLEAR_BIT(LPUARTx->CR1, USART_CR1_PEIE); } /** * @brief Disable Character Match Interrupt * @rmtoll CR1 CMIE LL_LPUART_DisableIT_CM * @param LPUARTx LPUART Instance * @retval None */ __STATIC_INLINE void LL_LPUART_DisableIT_CM(USART_TypeDef *LPUARTx) { ATOMIC_CLEAR_BIT(LPUARTx->CR1, USART_CR1_CMIE); } #if defined(USART_CR1_FIFOEN) /** * @brief Disable TX FIFO Empty Interrupt * @rmtoll CR1 TXFEIE LL_LPUART_DisableIT_TXFE * @param LPUARTx LPUART Instance * @retval None */ __STATIC_INLINE void LL_LPUART_DisableIT_TXFE(USART_TypeDef *LPUARTx) { ATOMIC_CLEAR_BIT(LPUARTx->CR1, USART_CR1_TXFEIE); } /** * @brief Disable RX FIFO Full Interrupt * @rmtoll CR1 RXFFIE LL_LPUART_DisableIT_RXFF * @param LPUARTx LPUART Instance * @retval None */ __STATIC_INLINE void LL_LPUART_DisableIT_RXFF(USART_TypeDef *LPUARTx) { ATOMIC_CLEAR_BIT(LPUARTx->CR1, USART_CR1_RXFFIE); } #endif /* USART_CR1_FIFOEN */ /** * @brief Disable Error Interrupt * @note When set, Error Interrupt Enable Bit is enabling interrupt generation in case of a framing * error, overrun error or noise flag (FE=1 or ORE=1 or NF=1 in the LPUARTx_ISR register). * - 0: Interrupt is inhibited * - 1: An interrupt is generated when FE=1 or ORE=1 or NF=1 in the LPUARTx_ISR register. * @rmtoll CR3 EIE LL_LPUART_DisableIT_ERROR * @param LPUARTx LPUART Instance * @retval None */ __STATIC_INLINE void LL_LPUART_DisableIT_ERROR(USART_TypeDef *LPUARTx) { ATOMIC_CLEAR_BIT(LPUARTx->CR3, USART_CR3_EIE); } /** * @brief Disable CTS Interrupt * @rmtoll CR3 CTSIE LL_LPUART_DisableIT_CTS * @param LPUARTx LPUART Instance * @retval None */ __STATIC_INLINE void LL_LPUART_DisableIT_CTS(USART_TypeDef *LPUARTx) { ATOMIC_CLEAR_BIT(LPUARTx->CR3, USART_CR3_CTSIE); } /** * @brief Disable Wake Up from Stop Mode Interrupt * @rmtoll CR3 WUFIE LL_LPUART_DisableIT_WKUP * @param LPUARTx LPUART Instance * @retval None */ __STATIC_INLINE void LL_LPUART_DisableIT_WKUP(USART_TypeDef *LPUARTx) { ATOMIC_CLEAR_BIT(LPUARTx->CR3, USART_CR3_WUFIE); } #if defined(USART_CR1_FIFOEN) /** * @brief Disable TX FIFO Threshold Interrupt * @rmtoll CR3 TXFTIE LL_LPUART_DisableIT_TXFT * @param LPUARTx LPUART Instance * @retval None */ __STATIC_INLINE void LL_LPUART_DisableIT_TXFT(USART_TypeDef *LPUARTx) { ATOMIC_CLEAR_BIT(LPUARTx->CR3, USART_CR3_TXFTIE); } /** * @brief Disable RX FIFO Threshold Interrupt * @rmtoll CR3 RXFTIE LL_LPUART_DisableIT_RXFT * @param LPUARTx LPUART Instance * @retval None */ __STATIC_INLINE void LL_LPUART_DisableIT_RXFT(USART_TypeDef *LPUARTx) { ATOMIC_CLEAR_BIT(LPUARTx->CR3, USART_CR3_RXFTIE); } #endif /* USART_CR1_FIFOEN */ /** * @brief Check if the LPUART IDLE Interrupt source is enabled or disabled. * @rmtoll CR1 IDLEIE LL_LPUART_IsEnabledIT_IDLE * @param LPUARTx LPUART Instance * @retval State of bit (1 or 0). */ __STATIC_INLINE uint32_t LL_LPUART_IsEnabledIT_IDLE(const USART_TypeDef *LPUARTx) { return ((READ_BIT(LPUARTx->CR1, USART_CR1_IDLEIE) == (USART_CR1_IDLEIE)) ? 1UL : 0UL); } #if defined(USART_CR1_FIFOEN) #define LL_LPUART_IsEnabledIT_RXNE LL_LPUART_IsEnabledIT_RXNE_RXFNE /* Redefinition for legacy purpose */ /** * @brief Check if the LPUART RX Not Empty and LPUART RX FIFO Not Empty Interrupt is enabled or disabled. * @rmtoll CR1 RXNEIE_RXFNEIE LL_LPUART_IsEnabledIT_RXNE_RXFNE * @param LPUARTx LPUART Instance * @retval State of bit (1 or 0). */ __STATIC_INLINE uint32_t LL_LPUART_IsEnabledIT_RXNE_RXFNE(const USART_TypeDef *LPUARTx) { return ((READ_BIT(LPUARTx->CR1, USART_CR1_RXNEIE_RXFNEIE) == (USART_CR1_RXNEIE_RXFNEIE)) ? 1UL : 0UL); } #else /** * @brief Check if the LPUART RX Not Empty Interrupt is enabled or disabled. * @rmtoll CR1 RXNEIE LL_LPUART_IsEnabledIT_RXNE * @param LPUARTx LPUART Instance * @retval State of bit (1 or 0). */ __STATIC_INLINE uint32_t LL_LPUART_IsEnabledIT_RXNE(const USART_TypeDef *LPUARTx) { return ((READ_BIT(LPUARTx->CR1, USART_CR1_RXNEIE) == (USART_CR1_RXNEIE)) ? 1UL : 0UL); } #endif /* USART_CR1_FIFOEN */ /** * @brief Check if the LPUART Transmission Complete Interrupt is enabled or disabled. * @rmtoll CR1 TCIE LL_LPUART_IsEnabledIT_TC * @param LPUARTx LPUART Instance * @retval State of bit (1 or 0). */ __STATIC_INLINE uint32_t LL_LPUART_IsEnabledIT_TC(const USART_TypeDef *LPUARTx) { return ((READ_BIT(LPUARTx->CR1, USART_CR1_TCIE) == (USART_CR1_TCIE)) ? 1UL : 0UL); } #if defined(USART_CR1_FIFOEN) #define LL_LPUART_IsEnabledIT_TXE LL_LPUART_IsEnabledIT_TXE_TXFNF /* Redefinition for legacy purpose */ /** * @brief Check if the LPUART TX Empty and LPUART TX FIFO Not Full Interrupt is enabled or disabled * @rmtoll CR1 TXEIE_TXFNFIE LL_LPUART_IsEnabledIT_TXE_TXFNF * @param LPUARTx LPUART Instance * @retval State of bit (1 or 0). */ __STATIC_INLINE uint32_t LL_LPUART_IsEnabledIT_TXE_TXFNF(const USART_TypeDef *LPUARTx) { return ((READ_BIT(LPUARTx->CR1, USART_CR1_TXEIE_TXFNFIE) == (USART_CR1_TXEIE_TXFNFIE)) ? 1UL : 0UL); } #else /** * @brief Check if the LPUART TX Empty Interrupt is enabled or disabled. * @rmtoll CR1 TXEIE LL_LPUART_IsEnabledIT_TXE * @param LPUARTx LPUART Instance * @retval State of bit (1 or 0). */ __STATIC_INLINE uint32_t LL_LPUART_IsEnabledIT_TXE(const USART_TypeDef *LPUARTx) { return ((READ_BIT(LPUARTx->CR1, USART_CR1_TXEIE) == (USART_CR1_TXEIE)) ? 1UL : 0UL); } #endif /* USART_CR1_FIFOEN */ /** * @brief Check if the LPUART Parity Error Interrupt is enabled or disabled. * @rmtoll CR1 PEIE LL_LPUART_IsEnabledIT_PE * @param LPUARTx LPUART Instance * @retval State of bit (1 or 0). */ __STATIC_INLINE uint32_t LL_LPUART_IsEnabledIT_PE(const USART_TypeDef *LPUARTx) { return ((READ_BIT(LPUARTx->CR1, USART_CR1_PEIE) == (USART_CR1_PEIE)) ? 1UL : 0UL); } /** * @brief Check if the LPUART Character Match Interrupt is enabled or disabled. * @rmtoll CR1 CMIE LL_LPUART_IsEnabledIT_CM * @param LPUARTx LPUART Instance * @retval State of bit (1 or 0). */ __STATIC_INLINE uint32_t LL_LPUART_IsEnabledIT_CM(const USART_TypeDef *LPUARTx) { return ((READ_BIT(LPUARTx->CR1, USART_CR1_CMIE) == (USART_CR1_CMIE)) ? 1UL : 0UL); } #if defined(USART_CR1_FIFOEN) /** * @brief Check if the LPUART TX FIFO Empty Interrupt is enabled or disabled * @rmtoll CR1 TXFEIE LL_LPUART_IsEnabledIT_TXFE * @param LPUARTx LPUART Instance * @retval State of bit (1 or 0). */ __STATIC_INLINE uint32_t LL_LPUART_IsEnabledIT_TXFE(const USART_TypeDef *LPUARTx) { return ((READ_BIT(LPUARTx->CR1, USART_CR1_TXFEIE) == (USART_CR1_TXFEIE)) ? 1UL : 0UL); } /** * @brief Check if the LPUART RX FIFO Full Interrupt is enabled or disabled * @rmtoll CR1 RXFFIE LL_LPUART_IsEnabledIT_RXFF * @param LPUARTx LPUART Instance * @retval State of bit (1 or 0). */ __STATIC_INLINE uint32_t LL_LPUART_IsEnabledIT_RXFF(const USART_TypeDef *LPUARTx) { return ((READ_BIT(LPUARTx->CR1, USART_CR1_RXFFIE) == (USART_CR1_RXFFIE)) ? 1UL : 0UL); } #endif /* USART_CR1_FIFOEN */ /** * @brief Check if the LPUART Error Interrupt is enabled or disabled. * @rmtoll CR3 EIE LL_LPUART_IsEnabledIT_ERROR * @param LPUARTx LPUART Instance * @retval State of bit (1 or 0). */ __STATIC_INLINE uint32_t LL_LPUART_IsEnabledIT_ERROR(const USART_TypeDef *LPUARTx) { return ((READ_BIT(LPUARTx->CR3, USART_CR3_EIE) == (USART_CR3_EIE)) ? 1UL : 0UL); } /** * @brief Check if the LPUART CTS Interrupt is enabled or disabled. * @rmtoll CR3 CTSIE LL_LPUART_IsEnabledIT_CTS * @param LPUARTx LPUART Instance * @retval State of bit (1 or 0). */ __STATIC_INLINE uint32_t LL_LPUART_IsEnabledIT_CTS(const USART_TypeDef *LPUARTx) { return ((READ_BIT(LPUARTx->CR3, USART_CR3_CTSIE) == (USART_CR3_CTSIE)) ? 1UL : 0UL); } /** * @brief Check if the LPUART Wake Up from Stop Mode Interrupt is enabled or disabled. * @rmtoll CR3 WUFIE LL_LPUART_IsEnabledIT_WKUP * @param LPUARTx LPUART Instance * @retval State of bit (1 or 0). */ __STATIC_INLINE uint32_t LL_LPUART_IsEnabledIT_WKUP(const USART_TypeDef *LPUARTx) { return ((READ_BIT(LPUARTx->CR3, USART_CR3_WUFIE) == (USART_CR3_WUFIE)) ? 1UL : 0UL); } #if defined(USART_CR1_FIFOEN) /** * @brief Check if LPUART TX FIFO Threshold Interrupt is enabled or disabled * @rmtoll CR3 TXFTIE LL_LPUART_IsEnabledIT_TXFT * @param LPUARTx LPUART Instance * @retval State of bit (1 or 0). */ __STATIC_INLINE uint32_t LL_LPUART_IsEnabledIT_TXFT(const USART_TypeDef *LPUARTx) { return ((READ_BIT(LPUARTx->CR3, USART_CR3_TXFTIE) == (USART_CR3_TXFTIE)) ? 1UL : 0UL); } /** * @brief Check if LPUART RX FIFO Threshold Interrupt is enabled or disabled * @rmtoll CR3 RXFTIE LL_LPUART_IsEnabledIT_RXFT * @param LPUARTx LPUART Instance * @retval State of bit (1 or 0). */ __STATIC_INLINE uint32_t LL_LPUART_IsEnabledIT_RXFT(const USART_TypeDef *LPUARTx) { return ((READ_BIT(LPUARTx->CR3, USART_CR3_RXFTIE) == (USART_CR3_RXFTIE)) ? 1UL : 0UL); } #endif /* USART_CR1_FIFOEN */ /** * @} */ /** @defgroup LPUART_LL_EF_DMA_Management DMA_Management * @{ */ /** * @brief Enable DMA Mode for reception * @rmtoll CR3 DMAR LL_LPUART_EnableDMAReq_RX * @param LPUARTx LPUART Instance * @retval None */ __STATIC_INLINE void LL_LPUART_EnableDMAReq_RX(USART_TypeDef *LPUARTx) { ATOMIC_SET_BIT(LPUARTx->CR3, USART_CR3_DMAR); } /** * @brief Disable DMA Mode for reception * @rmtoll CR3 DMAR LL_LPUART_DisableDMAReq_RX * @param LPUARTx LPUART Instance * @retval None */ __STATIC_INLINE void LL_LPUART_DisableDMAReq_RX(USART_TypeDef *LPUARTx) { ATOMIC_CLEAR_BIT(LPUARTx->CR3, USART_CR3_DMAR); } /** * @brief Check if DMA Mode is enabled for reception * @rmtoll CR3 DMAR LL_LPUART_IsEnabledDMAReq_RX * @param LPUARTx LPUART Instance * @retval State of bit (1 or 0). */ __STATIC_INLINE uint32_t LL_LPUART_IsEnabledDMAReq_RX(const USART_TypeDef *LPUARTx) { return ((READ_BIT(LPUARTx->CR3, USART_CR3_DMAR) == (USART_CR3_DMAR)) ? 1UL : 0UL); } /** * @brief Enable DMA Mode for transmission * @rmtoll CR3 DMAT LL_LPUART_EnableDMAReq_TX * @param LPUARTx LPUART Instance * @retval None */ __STATIC_INLINE void LL_LPUART_EnableDMAReq_TX(USART_TypeDef *LPUARTx) { ATOMIC_SET_BIT(LPUARTx->CR3, USART_CR3_DMAT); } /** * @brief Disable DMA Mode for transmission * @rmtoll CR3 DMAT LL_LPUART_DisableDMAReq_TX * @param LPUARTx LPUART Instance * @retval None */ __STATIC_INLINE void LL_LPUART_DisableDMAReq_TX(USART_TypeDef *LPUARTx) { ATOMIC_CLEAR_BIT(LPUARTx->CR3, USART_CR3_DMAT); } /** * @brief Check if DMA Mode is enabled for transmission * @rmtoll CR3 DMAT LL_LPUART_IsEnabledDMAReq_TX * @param LPUARTx LPUART Instance * @retval State of bit (1 or 0). */ __STATIC_INLINE uint32_t LL_LPUART_IsEnabledDMAReq_TX(const USART_TypeDef *LPUARTx) { return ((READ_BIT(LPUARTx->CR3, USART_CR3_DMAT) == (USART_CR3_DMAT)) ? 1UL : 0UL); } /** * @brief Enable DMA Disabling on Reception Error * @rmtoll CR3 DDRE LL_LPUART_EnableDMADeactOnRxErr * @param LPUARTx LPUART Instance * @retval None */ __STATIC_INLINE void LL_LPUART_EnableDMADeactOnRxErr(USART_TypeDef *LPUARTx) { SET_BIT(LPUARTx->CR3, USART_CR3_DDRE); } /** * @brief Disable DMA Disabling on Reception Error * @rmtoll CR3 DDRE LL_LPUART_DisableDMADeactOnRxErr * @param LPUARTx LPUART Instance * @retval None */ __STATIC_INLINE void LL_LPUART_DisableDMADeactOnRxErr(USART_TypeDef *LPUARTx) { CLEAR_BIT(LPUARTx->CR3, USART_CR3_DDRE); } /** * @brief Indicate if DMA Disabling on Reception Error is disabled * @rmtoll CR3 DDRE LL_LPUART_IsEnabledDMADeactOnRxErr * @param LPUARTx LPUART Instance * @retval State of bit (1 or 0). */ __STATIC_INLINE uint32_t LL_LPUART_IsEnabledDMADeactOnRxErr(const USART_TypeDef *LPUARTx) { return ((READ_BIT(LPUARTx->CR3, USART_CR3_DDRE) == (USART_CR3_DDRE)) ? 1UL : 0UL); } /** * @brief Get the LPUART data register address used for DMA transfer * @rmtoll RDR RDR LL_LPUART_DMA_GetRegAddr\n * @rmtoll TDR TDR LL_LPUART_DMA_GetRegAddr * @param LPUARTx LPUART Instance * @param Direction This parameter can be one of the following values: * @arg @ref LL_LPUART_DMA_REG_DATA_TRANSMIT * @arg @ref LL_LPUART_DMA_REG_DATA_RECEIVE * @retval Address of data register */ __STATIC_INLINE uint32_t LL_LPUART_DMA_GetRegAddr(const USART_TypeDef *LPUARTx, uint32_t Direction) { uint32_t data_reg_addr; if (Direction == LL_LPUART_DMA_REG_DATA_TRANSMIT) { /* return address of TDR register */ data_reg_addr = (uint32_t) &(LPUARTx->TDR); } else { /* return address of RDR register */ data_reg_addr = (uint32_t) &(LPUARTx->RDR); } return data_reg_addr; } /** * @} */ /** @defgroup LPUART_LL_EF_Data_Management Data_Management * @{ */ /** * @brief Read Receiver Data register (Receive Data value, 8 bits) * @rmtoll RDR RDR LL_LPUART_ReceiveData8 * @param LPUARTx LPUART Instance * @retval Time Value between Min_Data=0x00 and Max_Data=0xFF */ __STATIC_INLINE uint8_t LL_LPUART_ReceiveData8(const USART_TypeDef *LPUARTx) { return (uint8_t)(READ_BIT(LPUARTx->RDR, USART_RDR_RDR) & 0xFFU); } /** * @brief Read Receiver Data register (Receive Data value, 9 bits) * @rmtoll RDR RDR LL_LPUART_ReceiveData9 * @param LPUARTx LPUART Instance * @retval Time Value between Min_Data=0x00 and Max_Data=0x1FF */ __STATIC_INLINE uint16_t LL_LPUART_ReceiveData9(const USART_TypeDef *LPUARTx) { return (uint16_t)(READ_BIT(LPUARTx->RDR, USART_RDR_RDR)); } /** * @brief Write in Transmitter Data Register (Transmit Data value, 8 bits) * @rmtoll TDR TDR LL_LPUART_TransmitData8 * @param LPUARTx LPUART Instance * @param Value between Min_Data=0x00 and Max_Data=0xFF * @retval None */ __STATIC_INLINE void LL_LPUART_TransmitData8(USART_TypeDef *LPUARTx, uint8_t Value) { LPUARTx->TDR = Value; } /** * @brief Write in Transmitter Data Register (Transmit Data value, 9 bits) * @rmtoll TDR TDR LL_LPUART_TransmitData9 * @param LPUARTx LPUART Instance * @param Value between Min_Data=0x00 and Max_Data=0x1FF * @retval None */ __STATIC_INLINE void LL_LPUART_TransmitData9(USART_TypeDef *LPUARTx, uint16_t Value) { LPUARTx->TDR = Value & 0x1FFUL; } /** * @} */ /** @defgroup LPUART_LL_EF_Execution Execution * @{ */ /** * @brief Request Break sending * @rmtoll RQR SBKRQ LL_LPUART_RequestBreakSending * @param LPUARTx LPUART Instance * @retval None */ __STATIC_INLINE void LL_LPUART_RequestBreakSending(USART_TypeDef *LPUARTx) { SET_BIT(LPUARTx->RQR, (uint16_t)USART_RQR_SBKRQ); } /** * @brief Put LPUART in mute mode and set the RWU flag * @rmtoll RQR MMRQ LL_LPUART_RequestEnterMuteMode * @param LPUARTx LPUART Instance * @retval None */ __STATIC_INLINE void LL_LPUART_RequestEnterMuteMode(USART_TypeDef *LPUARTx) { SET_BIT(LPUARTx->RQR, (uint16_t)USART_RQR_MMRQ); } /** @if USART_CR1_FIFOEN * @brief Request a Receive Data and FIFO flush * @note Allows to discard the received data without reading them, and avoid an overrun * condition. @else * @brief Request a Receive Data flush @endif * @rmtoll RQR RXFRQ LL_LPUART_RequestRxDataFlush * @param LPUARTx LPUART Instance * @retval None */ __STATIC_INLINE void LL_LPUART_RequestRxDataFlush(USART_TypeDef *LPUARTx) { SET_BIT(LPUARTx->RQR, (uint16_t)USART_RQR_RXFRQ); } /** * @} */ #if defined(USE_FULL_LL_DRIVER) /** @defgroup LPUART_LL_EF_Init Initialization and de-initialization functions * @{ */ ErrorStatus LL_LPUART_DeInit(const USART_TypeDef *LPUARTx); ErrorStatus LL_LPUART_Init(USART_TypeDef *LPUARTx, const LL_LPUART_InitTypeDef *LPUART_InitStruct); void LL_LPUART_StructInit(LL_LPUART_InitTypeDef *LPUART_InitStruct); /** * @} */ #endif /* USE_FULL_LL_DRIVER */ /** * @} */ /** * @} */ #endif /* LPUART1 */ /** * @} */ #ifdef __cplusplus } #endif #endif /* STM32L4xx_LL_LPUART_H */