4484 lines
139 KiB
C
4484 lines
139 KiB
C
/**
|
|
******************************************************************************
|
|
* @file stm32l4xx_hal_spi.c
|
|
* @author MCD Application Team
|
|
* @brief SPI HAL module driver.
|
|
* This file provides firmware functions to manage the following
|
|
* functionalities of the Serial Peripheral Interface (SPI) peripheral:
|
|
* + Initialization and de-initialization functions
|
|
* + IO operation functions
|
|
* + Peripheral Control functions
|
|
* + Peripheral State functions
|
|
******************************************************************************
|
|
* @attention
|
|
*
|
|
* Copyright (c) 2017 STMicroelectronics.
|
|
* All rights reserved.
|
|
*
|
|
* This software is licensed under terms that can be found in the LICENSE file
|
|
* in the root directory of this software component.
|
|
* If no LICENSE file comes with this software, it is provided AS-IS.
|
|
*
|
|
******************************************************************************
|
|
@verbatim
|
|
==============================================================================
|
|
##### How to use this driver #####
|
|
==============================================================================
|
|
[..]
|
|
The SPI HAL driver can be used as follows:
|
|
|
|
(#) Declare a SPI_HandleTypeDef handle structure, for example:
|
|
SPI_HandleTypeDef hspi;
|
|
|
|
(#)Initialize the SPI low level resources by implementing the HAL_SPI_MspInit() API:
|
|
(##) Enable the SPIx interface clock
|
|
(##) SPI pins configuration
|
|
(+++) Enable the clock for the SPI GPIOs
|
|
(+++) Configure these SPI pins as alternate function push-pull
|
|
(##) NVIC configuration if you need to use interrupt process
|
|
(+++) Configure the SPIx interrupt priority
|
|
(+++) Enable the NVIC SPI IRQ handle
|
|
(##) DMA Configuration if you need to use DMA process
|
|
(+++) Declare a DMA_HandleTypeDef handle structure for the transmit or receive Stream/Channel
|
|
(+++) Enable the DMAx clock
|
|
(+++) Configure the DMA handle parameters
|
|
(+++) Configure the DMA Tx or Rx Stream/Channel
|
|
(+++) Associate the initialized hdma_tx(or _rx) handle to the hspi DMA Tx or Rx handle
|
|
(+++) Configure the priority and enable the NVIC for the transfer complete interrupt on the DMA Tx or Rx Stream/Channel
|
|
|
|
(#) Program the Mode, BidirectionalMode , Data size, Baudrate Prescaler, NSS
|
|
management, Clock polarity and phase, FirstBit and CRC configuration in the hspi Init structure.
|
|
|
|
(#) Initialize the SPI registers by calling the HAL_SPI_Init() API:
|
|
(++) This API configures also the low level Hardware GPIO, CLOCK, CORTEX...etc)
|
|
by calling the customized HAL_SPI_MspInit() API.
|
|
[..]
|
|
Circular mode restriction:
|
|
(#) The DMA circular mode cannot be used when the SPI is configured in these modes:
|
|
(##) Master 2Lines RxOnly
|
|
(##) Master 1Line Rx
|
|
(#) The CRC feature is not managed when the DMA circular mode is enabled
|
|
(#) When the SPI DMA Pause/Stop features are used, we must use the following APIs
|
|
the HAL_SPI_DMAPause()/ HAL_SPI_DMAStop() only under the SPI callbacks
|
|
[..]
|
|
Master Receive mode restriction:
|
|
(#) In Master unidirectional receive-only mode (MSTR =1, BIDIMODE=0, RXONLY=1) or
|
|
bidirectional receive mode (MSTR=1, BIDIMODE=1, BIDIOE=0), to ensure that the SPI
|
|
does not initiate a new transfer the following procedure has to be respected:
|
|
(##) HAL_SPI_DeInit()
|
|
(##) HAL_SPI_Init()
|
|
[..]
|
|
Callback registration:
|
|
|
|
(#) The compilation flag USE_HAL_SPI_REGISTER_CALLBACKS when set to 1U
|
|
allows the user to configure dynamically the driver callbacks.
|
|
Use Functions HAL_SPI_RegisterCallback() to register an interrupt callback.
|
|
|
|
Function HAL_SPI_RegisterCallback() allows to register following callbacks:
|
|
(++) TxCpltCallback : SPI Tx Completed callback
|
|
(++) RxCpltCallback : SPI Rx Completed callback
|
|
(++) TxRxCpltCallback : SPI TxRx Completed callback
|
|
(++) TxHalfCpltCallback : SPI Tx Half Completed callback
|
|
(++) RxHalfCpltCallback : SPI Rx Half Completed callback
|
|
(++) TxRxHalfCpltCallback : SPI TxRx Half Completed callback
|
|
(++) ErrorCallback : SPI Error callback
|
|
(++) AbortCpltCallback : SPI Abort callback
|
|
(++) MspInitCallback : SPI Msp Init callback
|
|
(++) MspDeInitCallback : SPI Msp DeInit callback
|
|
This function takes as parameters the HAL peripheral handle, the Callback ID
|
|
and a pointer to the user callback function.
|
|
|
|
|
|
(#) Use function HAL_SPI_UnRegisterCallback to reset a callback to the default
|
|
weak function.
|
|
HAL_SPI_UnRegisterCallback takes as parameters the HAL peripheral handle,
|
|
and the Callback ID.
|
|
This function allows to reset following callbacks:
|
|
(++) TxCpltCallback : SPI Tx Completed callback
|
|
(++) RxCpltCallback : SPI Rx Completed callback
|
|
(++) TxRxCpltCallback : SPI TxRx Completed callback
|
|
(++) TxHalfCpltCallback : SPI Tx Half Completed callback
|
|
(++) RxHalfCpltCallback : SPI Rx Half Completed callback
|
|
(++) TxRxHalfCpltCallback : SPI TxRx Half Completed callback
|
|
(++) ErrorCallback : SPI Error callback
|
|
(++) AbortCpltCallback : SPI Abort callback
|
|
(++) MspInitCallback : SPI Msp Init callback
|
|
(++) MspDeInitCallback : SPI Msp DeInit callback
|
|
|
|
[..]
|
|
By default, after the HAL_SPI_Init() and when the state is HAL_SPI_STATE_RESET
|
|
all callbacks are set to the corresponding weak functions:
|
|
examples HAL_SPI_MasterTxCpltCallback(), HAL_SPI_MasterRxCpltCallback().
|
|
Exception done for MspInit and MspDeInit functions that are
|
|
reset to the legacy weak functions in the HAL_SPI_Init()/ HAL_SPI_DeInit() only when
|
|
these callbacks are null (not registered beforehand).
|
|
If MspInit or MspDeInit are not null, the HAL_SPI_Init()/ HAL_SPI_DeInit()
|
|
keep and use the user MspInit/MspDeInit callbacks (registered beforehand) whatever the state.
|
|
|
|
[..]
|
|
Callbacks can be registered/unregistered in HAL_SPI_STATE_READY state only.
|
|
Exception done MspInit/MspDeInit functions that can be registered/unregistered
|
|
in HAL_SPI_STATE_READY or HAL_SPI_STATE_RESET state,
|
|
thus registered (user) MspInit/DeInit callbacks can be used during the Init/DeInit.
|
|
Then, the user first registers the MspInit/MspDeInit user callbacks
|
|
using HAL_SPI_RegisterCallback() before calling HAL_SPI_DeInit()
|
|
or HAL_SPI_Init() function.
|
|
|
|
[..]
|
|
When the compilation define USE_HAL_PPP_REGISTER_CALLBACKS is set to 0 or
|
|
not defined, the callback registering feature is not available
|
|
and weak (surcharged) callbacks are used.
|
|
|
|
[..]
|
|
Using the HAL it is not possible to reach all supported SPI frequency with the different SPI Modes,
|
|
the following table resume the max SPI frequency reached with data size 8bits/16bits,
|
|
according to frequency of the APBx Peripheral Clock (fPCLK) used by the SPI instance.
|
|
|
|
@endverbatim
|
|
|
|
Additional table :
|
|
|
|
DataSize = SPI_DATASIZE_8BIT:
|
|
+----------------------------------------------------------------------------------------------+
|
|
| | | 2Lines Fullduplex | 2Lines RxOnly | 1Line |
|
|
| Process | Transfer mode |---------------------|----------------------|----------------------|
|
|
| | | Master | Slave | Master | Slave | Master | Slave |
|
|
|==============================================================================================|
|
|
| T | Polling | Fpclk/4 | Fpclk/8 | NA | NA | NA | NA |
|
|
| X |----------------|----------|----------|-----------|----------|-----------|----------|
|
|
| / | Interrupt | Fpclk/4 | Fpclk/16 | NA | NA | NA | NA |
|
|
| R |----------------|----------|----------|-----------|----------|-----------|----------|
|
|
| X | DMA | Fpclk/2 | Fpclk/2 | NA | NA | NA | NA |
|
|
|=========|================|==========|==========|===========|==========|===========|==========|
|
|
| | Polling | Fpclk/4 | Fpclk/8 | Fpclk/16 | Fpclk/8 | Fpclk/8 | Fpclk/8 |
|
|
| |----------------|----------|----------|-----------|----------|-----------|----------|
|
|
| R | Interrupt | Fpclk/8 | Fpclk/16 | Fpclk/8 | Fpclk/8 | Fpclk/8 | Fpclk/4 |
|
|
| X |----------------|----------|----------|-----------|----------|-----------|----------|
|
|
| | DMA | Fpclk/4 | Fpclk/2 | Fpclk/2 | Fpclk/16 | Fpclk/2 | Fpclk/16 |
|
|
|=========|================|==========|==========|===========|==========|===========|==========|
|
|
| | Polling | Fpclk/8 | Fpclk/2 | NA | NA | Fpclk/8 | Fpclk/8 |
|
|
| |----------------|----------|----------|-----------|----------|-----------|----------|
|
|
| T | Interrupt | Fpclk/2 | Fpclk/4 | NA | NA | Fpclk/16 | Fpclk/8 |
|
|
| X |----------------|----------|----------|-----------|----------|-----------|----------|
|
|
| | DMA | Fpclk/2 | Fpclk/2 | NA | NA | Fpclk/8 | Fpclk/16 |
|
|
+----------------------------------------------------------------------------------------------+
|
|
|
|
DataSize = SPI_DATASIZE_16BIT:
|
|
+----------------------------------------------------------------------------------------------+
|
|
| | | 2Lines Fullduplex | 2Lines RxOnly | 1Line |
|
|
| Process | Transfer mode |---------------------|----------------------|----------------------|
|
|
| | | Master | Slave | Master | Slave | Master | Slave |
|
|
|==============================================================================================|
|
|
| T | Polling | Fpclk/4 | Fpclk/8 | NA | NA | NA | NA |
|
|
| X |----------------|----------|----------|-----------|----------|-----------|----------|
|
|
| / | Interrupt | Fpclk/4 | Fpclk/16 | NA | NA | NA | NA |
|
|
| R |----------------|----------|----------|-----------|----------|-----------|----------|
|
|
| X | DMA | Fpclk/2 | Fpclk/2 | NA | NA | NA | NA |
|
|
|=========|================|==========|==========|===========|==========|===========|==========|
|
|
| | Polling | Fpclk/4 | Fpclk/8 | Fpclk/16 | Fpclk/8 | Fpclk/8 | Fpclk/8 |
|
|
| |----------------|----------|----------|-----------|----------|-----------|----------|
|
|
| R | Interrupt | Fpclk/8 | Fpclk/16 | Fpclk/8 | Fpclk/8 | Fpclk/8 | Fpclk/4 |
|
|
| X |----------------|----------|----------|-----------|----------|-----------|----------|
|
|
| | DMA | Fpclk/4 | Fpclk/2 | Fpclk/2 | Fpclk/16 | Fpclk/2 | Fpclk/16 |
|
|
|=========|================|==========|==========|===========|==========|===========|==========|
|
|
| | Polling | Fpclk/8 | Fpclk/2 | NA | NA | Fpclk/8 | Fpclk/8 |
|
|
| |----------------|----------|----------|-----------|----------|-----------|----------|
|
|
| T | Interrupt | Fpclk/2 | Fpclk/4 | NA | NA | Fpclk/16 | Fpclk/8 |
|
|
| X |----------------|----------|----------|-----------|----------|-----------|----------|
|
|
| | DMA | Fpclk/2 | Fpclk/2 | NA | NA | Fpclk/8 | Fpclk/16 |
|
|
+----------------------------------------------------------------------------------------------+
|
|
@note The max SPI frequency depend on SPI data size (4bits, 5bits,..., 8bits,...15bits, 16bits),
|
|
SPI mode(2 Lines fullduplex, 2 lines RxOnly, 1 line TX/RX) and Process mode (Polling, IT, DMA).
|
|
@note
|
|
(#) TX/RX processes are HAL_SPI_TransmitReceive(), HAL_SPI_TransmitReceive_IT() and HAL_SPI_TransmitReceive_DMA()
|
|
(#) RX processes are HAL_SPI_Receive(), HAL_SPI_Receive_IT() and HAL_SPI_Receive_DMA()
|
|
(#) TX processes are HAL_SPI_Transmit(), HAL_SPI_Transmit_IT() and HAL_SPI_Transmit_DMA()
|
|
|
|
*/
|
|
|
|
/* Includes ------------------------------------------------------------------*/
|
|
#include "stm32l4xx_hal.h"
|
|
|
|
/** @addtogroup STM32L4xx_HAL_Driver
|
|
* @{
|
|
*/
|
|
|
|
/** @defgroup SPI SPI
|
|
* @brief SPI HAL module driver
|
|
* @{
|
|
*/
|
|
#ifdef HAL_SPI_MODULE_ENABLED
|
|
|
|
/* Private typedef -----------------------------------------------------------*/
|
|
/* Private defines -----------------------------------------------------------*/
|
|
/** @defgroup SPI_Private_Constants SPI Private Constants
|
|
* @{
|
|
*/
|
|
#define SPI_DEFAULT_TIMEOUT 100U
|
|
/**
|
|
* @}
|
|
*/
|
|
|
|
/* Private macros ------------------------------------------------------------*/
|
|
/* Private variables ---------------------------------------------------------*/
|
|
/* Private function prototypes -----------------------------------------------*/
|
|
/** @defgroup SPI_Private_Functions SPI Private Functions
|
|
* @{
|
|
*/
|
|
static void SPI_DMATransmitCplt(DMA_HandleTypeDef *hdma);
|
|
static void SPI_DMAReceiveCplt(DMA_HandleTypeDef *hdma);
|
|
static void SPI_DMATransmitReceiveCplt(DMA_HandleTypeDef *hdma);
|
|
static void SPI_DMAHalfTransmitCplt(DMA_HandleTypeDef *hdma);
|
|
static void SPI_DMAHalfReceiveCplt(DMA_HandleTypeDef *hdma);
|
|
static void SPI_DMAHalfTransmitReceiveCplt(DMA_HandleTypeDef *hdma);
|
|
static void SPI_DMAError(DMA_HandleTypeDef *hdma);
|
|
static void SPI_DMAAbortOnError(DMA_HandleTypeDef *hdma);
|
|
static void SPI_DMATxAbortCallback(DMA_HandleTypeDef *hdma);
|
|
static void SPI_DMARxAbortCallback(DMA_HandleTypeDef *hdma);
|
|
static HAL_StatusTypeDef SPI_WaitFlagStateUntilTimeout(SPI_HandleTypeDef *hspi, uint32_t Flag, FlagStatus State,
|
|
uint32_t Timeout, uint32_t Tickstart);
|
|
static HAL_StatusTypeDef SPI_WaitFifoStateUntilTimeout(SPI_HandleTypeDef *hspi, uint32_t Fifo, uint32_t State,
|
|
uint32_t Timeout, uint32_t Tickstart);
|
|
static void SPI_TxISR_8BIT(struct __SPI_HandleTypeDef *hspi);
|
|
static void SPI_TxISR_16BIT(struct __SPI_HandleTypeDef *hspi);
|
|
static void SPI_RxISR_8BIT(struct __SPI_HandleTypeDef *hspi);
|
|
static void SPI_RxISR_16BIT(struct __SPI_HandleTypeDef *hspi);
|
|
static void SPI_2linesRxISR_8BIT(struct __SPI_HandleTypeDef *hspi);
|
|
static void SPI_2linesTxISR_8BIT(struct __SPI_HandleTypeDef *hspi);
|
|
static void SPI_2linesTxISR_16BIT(struct __SPI_HandleTypeDef *hspi);
|
|
static void SPI_2linesRxISR_16BIT(struct __SPI_HandleTypeDef *hspi);
|
|
#if (USE_SPI_CRC != 0U)
|
|
static void SPI_RxISR_8BITCRC(struct __SPI_HandleTypeDef *hspi);
|
|
static void SPI_RxISR_16BITCRC(struct __SPI_HandleTypeDef *hspi);
|
|
static void SPI_2linesRxISR_8BITCRC(struct __SPI_HandleTypeDef *hspi);
|
|
static void SPI_2linesRxISR_16BITCRC(struct __SPI_HandleTypeDef *hspi);
|
|
#endif /* USE_SPI_CRC */
|
|
static void SPI_AbortRx_ISR(SPI_HandleTypeDef *hspi);
|
|
static void SPI_AbortTx_ISR(SPI_HandleTypeDef *hspi);
|
|
static void SPI_CloseRxTx_ISR(SPI_HandleTypeDef *hspi);
|
|
static void SPI_CloseRx_ISR(SPI_HandleTypeDef *hspi);
|
|
static void SPI_CloseTx_ISR(SPI_HandleTypeDef *hspi);
|
|
static HAL_StatusTypeDef SPI_EndRxTransaction(SPI_HandleTypeDef *hspi, uint32_t Timeout, uint32_t Tickstart);
|
|
static HAL_StatusTypeDef SPI_EndRxTxTransaction(SPI_HandleTypeDef *hspi, uint32_t Timeout, uint32_t Tickstart);
|
|
/**
|
|
* @}
|
|
*/
|
|
|
|
/* Exported functions --------------------------------------------------------*/
|
|
/** @defgroup SPI_Exported_Functions SPI Exported Functions
|
|
* @{
|
|
*/
|
|
|
|
/** @defgroup SPI_Exported_Functions_Group1 Initialization and de-initialization functions
|
|
* @brief Initialization and Configuration functions
|
|
*
|
|
@verbatim
|
|
===============================================================================
|
|
##### Initialization and de-initialization functions #####
|
|
===============================================================================
|
|
[..] This subsection provides a set of functions allowing to initialize and
|
|
de-initialize the SPIx peripheral:
|
|
|
|
(+) User must implement HAL_SPI_MspInit() function in which he configures
|
|
all related peripherals resources (CLOCK, GPIO, DMA, IT and NVIC ).
|
|
|
|
(+) Call the function HAL_SPI_Init() to configure the selected device with
|
|
the selected configuration:
|
|
(++) Mode
|
|
(++) Direction
|
|
(++) Data Size
|
|
(++) Clock Polarity and Phase
|
|
(++) NSS Management
|
|
(++) BaudRate Prescaler
|
|
(++) FirstBit
|
|
(++) TIMode
|
|
(++) CRC Calculation
|
|
(++) CRC Polynomial if CRC enabled
|
|
(++) CRC Length, used only with Data8 and Data16
|
|
(++) FIFO reception threshold
|
|
|
|
(+) Call the function HAL_SPI_DeInit() to restore the default configuration
|
|
of the selected SPIx peripheral.
|
|
|
|
@endverbatim
|
|
* @{
|
|
*/
|
|
|
|
/**
|
|
* @brief Initialize the SPI according to the specified parameters
|
|
* in the SPI_InitTypeDef and initialize the associated handle.
|
|
* @param hspi pointer to a SPI_HandleTypeDef structure that contains
|
|
* the configuration information for SPI module.
|
|
* @retval HAL status
|
|
*/
|
|
HAL_StatusTypeDef HAL_SPI_Init(SPI_HandleTypeDef *hspi)
|
|
{
|
|
uint32_t frxth;
|
|
|
|
/* Check the SPI handle allocation */
|
|
if (hspi == NULL)
|
|
{
|
|
return HAL_ERROR;
|
|
}
|
|
|
|
/* Check the parameters */
|
|
assert_param(IS_SPI_ALL_INSTANCE(hspi->Instance));
|
|
assert_param(IS_SPI_MODE(hspi->Init.Mode));
|
|
assert_param(IS_SPI_DIRECTION(hspi->Init.Direction));
|
|
assert_param(IS_SPI_DATASIZE(hspi->Init.DataSize));
|
|
assert_param(IS_SPI_NSS(hspi->Init.NSS));
|
|
assert_param(IS_SPI_NSSP(hspi->Init.NSSPMode));
|
|
assert_param(IS_SPI_BAUDRATE_PRESCALER(hspi->Init.BaudRatePrescaler));
|
|
assert_param(IS_SPI_FIRST_BIT(hspi->Init.FirstBit));
|
|
assert_param(IS_SPI_TIMODE(hspi->Init.TIMode));
|
|
if (hspi->Init.TIMode == SPI_TIMODE_DISABLE)
|
|
{
|
|
assert_param(IS_SPI_CPOL(hspi->Init.CLKPolarity));
|
|
assert_param(IS_SPI_CPHA(hspi->Init.CLKPhase));
|
|
|
|
if (hspi->Init.Mode == SPI_MODE_MASTER)
|
|
{
|
|
assert_param(IS_SPI_BAUDRATE_PRESCALER(hspi->Init.BaudRatePrescaler));
|
|
}
|
|
else
|
|
{
|
|
/* Baudrate prescaler not use in Motoraola Slave mode. force to default value */
|
|
hspi->Init.BaudRatePrescaler = SPI_BAUDRATEPRESCALER_2;
|
|
}
|
|
}
|
|
else
|
|
{
|
|
assert_param(IS_SPI_BAUDRATE_PRESCALER(hspi->Init.BaudRatePrescaler));
|
|
|
|
/* Force polarity and phase to TI protocaol requirements */
|
|
hspi->Init.CLKPolarity = SPI_POLARITY_LOW;
|
|
hspi->Init.CLKPhase = SPI_PHASE_1EDGE;
|
|
}
|
|
#if (USE_SPI_CRC != 0U)
|
|
assert_param(IS_SPI_CRC_CALCULATION(hspi->Init.CRCCalculation));
|
|
if (hspi->Init.CRCCalculation == SPI_CRCCALCULATION_ENABLE)
|
|
{
|
|
assert_param(IS_SPI_CRC_POLYNOMIAL(hspi->Init.CRCPolynomial));
|
|
assert_param(IS_SPI_CRC_LENGTH(hspi->Init.CRCLength));
|
|
}
|
|
#else
|
|
hspi->Init.CRCCalculation = SPI_CRCCALCULATION_DISABLE;
|
|
#endif /* USE_SPI_CRC */
|
|
|
|
if (hspi->State == HAL_SPI_STATE_RESET)
|
|
{
|
|
/* Allocate lock resource and initialize it */
|
|
hspi->Lock = HAL_UNLOCKED;
|
|
|
|
#if (USE_HAL_SPI_REGISTER_CALLBACKS == 1U)
|
|
/* Init the SPI Callback settings */
|
|
hspi->TxCpltCallback = HAL_SPI_TxCpltCallback; /* Legacy weak TxCpltCallback */
|
|
hspi->RxCpltCallback = HAL_SPI_RxCpltCallback; /* Legacy weak RxCpltCallback */
|
|
hspi->TxRxCpltCallback = HAL_SPI_TxRxCpltCallback; /* Legacy weak TxRxCpltCallback */
|
|
hspi->TxHalfCpltCallback = HAL_SPI_TxHalfCpltCallback; /* Legacy weak TxHalfCpltCallback */
|
|
hspi->RxHalfCpltCallback = HAL_SPI_RxHalfCpltCallback; /* Legacy weak RxHalfCpltCallback */
|
|
hspi->TxRxHalfCpltCallback = HAL_SPI_TxRxHalfCpltCallback; /* Legacy weak TxRxHalfCpltCallback */
|
|
hspi->ErrorCallback = HAL_SPI_ErrorCallback; /* Legacy weak ErrorCallback */
|
|
hspi->AbortCpltCallback = HAL_SPI_AbortCpltCallback; /* Legacy weak AbortCpltCallback */
|
|
|
|
if (hspi->MspInitCallback == NULL)
|
|
{
|
|
hspi->MspInitCallback = HAL_SPI_MspInit; /* Legacy weak MspInit */
|
|
}
|
|
|
|
/* Init the low level hardware : GPIO, CLOCK, NVIC... */
|
|
hspi->MspInitCallback(hspi);
|
|
#else
|
|
/* Init the low level hardware : GPIO, CLOCK, NVIC... */
|
|
HAL_SPI_MspInit(hspi);
|
|
#endif /* USE_HAL_SPI_REGISTER_CALLBACKS */
|
|
}
|
|
|
|
hspi->State = HAL_SPI_STATE_BUSY;
|
|
|
|
/* Disable the selected SPI peripheral */
|
|
__HAL_SPI_DISABLE(hspi);
|
|
|
|
/* Align by default the rs fifo threshold on the data size */
|
|
if (hspi->Init.DataSize > SPI_DATASIZE_8BIT)
|
|
{
|
|
frxth = SPI_RXFIFO_THRESHOLD_HF;
|
|
}
|
|
else
|
|
{
|
|
frxth = SPI_RXFIFO_THRESHOLD_QF;
|
|
}
|
|
|
|
/* CRC calculation is valid only for 16Bit and 8 Bit */
|
|
if ((hspi->Init.DataSize != SPI_DATASIZE_16BIT) && (hspi->Init.DataSize != SPI_DATASIZE_8BIT))
|
|
{
|
|
/* CRC must be disabled */
|
|
hspi->Init.CRCCalculation = SPI_CRCCALCULATION_DISABLE;
|
|
}
|
|
|
|
/*----------------------- SPIx CR1 & CR2 Configuration ---------------------*/
|
|
/* Configure : SPI Mode, Communication Mode, Clock polarity and phase, NSS management,
|
|
Communication speed, First bit and CRC calculation state */
|
|
WRITE_REG(hspi->Instance->CR1, ((hspi->Init.Mode & (SPI_CR1_MSTR | SPI_CR1_SSI)) |
|
|
(hspi->Init.Direction & (SPI_CR1_RXONLY | SPI_CR1_BIDIMODE)) |
|
|
(hspi->Init.CLKPolarity & SPI_CR1_CPOL) |
|
|
(hspi->Init.CLKPhase & SPI_CR1_CPHA) |
|
|
(hspi->Init.NSS & SPI_CR1_SSM) |
|
|
(hspi->Init.BaudRatePrescaler & SPI_CR1_BR_Msk) |
|
|
(hspi->Init.FirstBit & SPI_CR1_LSBFIRST) |
|
|
(hspi->Init.CRCCalculation & SPI_CR1_CRCEN)));
|
|
#if (USE_SPI_CRC != 0U)
|
|
/*---------------------------- SPIx CRCL Configuration -------------------*/
|
|
if (hspi->Init.CRCCalculation == SPI_CRCCALCULATION_ENABLE)
|
|
{
|
|
/* Align the CRC Length on the data size */
|
|
if (hspi->Init.CRCLength == SPI_CRC_LENGTH_DATASIZE)
|
|
{
|
|
/* CRC Length aligned on the data size : value set by default */
|
|
if (hspi->Init.DataSize > SPI_DATASIZE_8BIT)
|
|
{
|
|
hspi->Init.CRCLength = SPI_CRC_LENGTH_16BIT;
|
|
}
|
|
else
|
|
{
|
|
hspi->Init.CRCLength = SPI_CRC_LENGTH_8BIT;
|
|
}
|
|
}
|
|
|
|
/* Configure : CRC Length */
|
|
if (hspi->Init.CRCLength == SPI_CRC_LENGTH_16BIT)
|
|
{
|
|
SET_BIT(hspi->Instance->CR1, SPI_CR1_CRCL);
|
|
}
|
|
}
|
|
#endif /* USE_SPI_CRC */
|
|
|
|
/* Configure : NSS management, TI Mode, NSS Pulse, Data size and Rx Fifo threshold */
|
|
WRITE_REG(hspi->Instance->CR2, (((hspi->Init.NSS >> 16U) & SPI_CR2_SSOE) |
|
|
(hspi->Init.TIMode & SPI_CR2_FRF) |
|
|
(hspi->Init.NSSPMode & SPI_CR2_NSSP) |
|
|
(hspi->Init.DataSize & SPI_CR2_DS_Msk) |
|
|
(frxth & SPI_CR2_FRXTH)));
|
|
|
|
#if (USE_SPI_CRC != 0U)
|
|
/*---------------------------- SPIx CRCPOLY Configuration ------------------*/
|
|
/* Configure : CRC Polynomial */
|
|
if (hspi->Init.CRCCalculation == SPI_CRCCALCULATION_ENABLE)
|
|
{
|
|
WRITE_REG(hspi->Instance->CRCPR, (hspi->Init.CRCPolynomial & SPI_CRCPR_CRCPOLY_Msk));
|
|
}
|
|
#endif /* USE_SPI_CRC */
|
|
|
|
#if defined(SPI_I2SCFGR_I2SMOD)
|
|
/* Activate the SPI mode (Make sure that I2SMOD bit in I2SCFGR register is reset) */
|
|
CLEAR_BIT(hspi->Instance->I2SCFGR, SPI_I2SCFGR_I2SMOD);
|
|
#endif /* SPI_I2SCFGR_I2SMOD */
|
|
|
|
hspi->ErrorCode = HAL_SPI_ERROR_NONE;
|
|
hspi->State = HAL_SPI_STATE_READY;
|
|
|
|
return HAL_OK;
|
|
}
|
|
|
|
/**
|
|
* @brief De-Initialize the SPI peripheral.
|
|
* @param hspi pointer to a SPI_HandleTypeDef structure that contains
|
|
* the configuration information for SPI module.
|
|
* @retval HAL status
|
|
*/
|
|
HAL_StatusTypeDef HAL_SPI_DeInit(SPI_HandleTypeDef *hspi)
|
|
{
|
|
/* Check the SPI handle allocation */
|
|
if (hspi == NULL)
|
|
{
|
|
return HAL_ERROR;
|
|
}
|
|
|
|
/* Check SPI Instance parameter */
|
|
assert_param(IS_SPI_ALL_INSTANCE(hspi->Instance));
|
|
|
|
hspi->State = HAL_SPI_STATE_BUSY;
|
|
|
|
/* Disable the SPI Peripheral Clock */
|
|
__HAL_SPI_DISABLE(hspi);
|
|
|
|
#if (USE_HAL_SPI_REGISTER_CALLBACKS == 1U)
|
|
if (hspi->MspDeInitCallback == NULL)
|
|
{
|
|
hspi->MspDeInitCallback = HAL_SPI_MspDeInit; /* Legacy weak MspDeInit */
|
|
}
|
|
|
|
/* DeInit the low level hardware: GPIO, CLOCK, NVIC... */
|
|
hspi->MspDeInitCallback(hspi);
|
|
#else
|
|
/* DeInit the low level hardware: GPIO, CLOCK, NVIC... */
|
|
HAL_SPI_MspDeInit(hspi);
|
|
#endif /* USE_HAL_SPI_REGISTER_CALLBACKS */
|
|
|
|
hspi->ErrorCode = HAL_SPI_ERROR_NONE;
|
|
hspi->State = HAL_SPI_STATE_RESET;
|
|
|
|
/* Release Lock */
|
|
__HAL_UNLOCK(hspi);
|
|
|
|
return HAL_OK;
|
|
}
|
|
|
|
/**
|
|
* @brief Initialize the SPI MSP.
|
|
* @param hspi pointer to a SPI_HandleTypeDef structure that contains
|
|
* the configuration information for SPI module.
|
|
* @retval None
|
|
*/
|
|
__weak void HAL_SPI_MspInit(SPI_HandleTypeDef *hspi)
|
|
{
|
|
/* Prevent unused argument(s) compilation warning */
|
|
UNUSED(hspi);
|
|
|
|
/* NOTE : This function should not be modified, when the callback is needed,
|
|
the HAL_SPI_MspInit should be implemented in the user file
|
|
*/
|
|
}
|
|
|
|
/**
|
|
* @brief De-Initialize the SPI MSP.
|
|
* @param hspi pointer to a SPI_HandleTypeDef structure that contains
|
|
* the configuration information for SPI module.
|
|
* @retval None
|
|
*/
|
|
__weak void HAL_SPI_MspDeInit(SPI_HandleTypeDef *hspi)
|
|
{
|
|
/* Prevent unused argument(s) compilation warning */
|
|
UNUSED(hspi);
|
|
|
|
/* NOTE : This function should not be modified, when the callback is needed,
|
|
the HAL_SPI_MspDeInit should be implemented in the user file
|
|
*/
|
|
}
|
|
|
|
#if (USE_HAL_SPI_REGISTER_CALLBACKS == 1U)
|
|
/**
|
|
* @brief Register a User SPI Callback
|
|
* To be used instead of the weak predefined callback
|
|
* @param hspi Pointer to a SPI_HandleTypeDef structure that contains
|
|
* the configuration information for the specified SPI.
|
|
* @param CallbackID ID of the callback to be registered
|
|
* @param pCallback pointer to the Callback function
|
|
* @retval HAL status
|
|
*/
|
|
HAL_StatusTypeDef HAL_SPI_RegisterCallback(SPI_HandleTypeDef *hspi, HAL_SPI_CallbackIDTypeDef CallbackID,
|
|
pSPI_CallbackTypeDef pCallback)
|
|
{
|
|
HAL_StatusTypeDef status = HAL_OK;
|
|
|
|
if (pCallback == NULL)
|
|
{
|
|
/* Update the error code */
|
|
hspi->ErrorCode |= HAL_SPI_ERROR_INVALID_CALLBACK;
|
|
|
|
return HAL_ERROR;
|
|
}
|
|
/* Process locked */
|
|
__HAL_LOCK(hspi);
|
|
|
|
if (HAL_SPI_STATE_READY == hspi->State)
|
|
{
|
|
switch (CallbackID)
|
|
{
|
|
case HAL_SPI_TX_COMPLETE_CB_ID :
|
|
hspi->TxCpltCallback = pCallback;
|
|
break;
|
|
|
|
case HAL_SPI_RX_COMPLETE_CB_ID :
|
|
hspi->RxCpltCallback = pCallback;
|
|
break;
|
|
|
|
case HAL_SPI_TX_RX_COMPLETE_CB_ID :
|
|
hspi->TxRxCpltCallback = pCallback;
|
|
break;
|
|
|
|
case HAL_SPI_TX_HALF_COMPLETE_CB_ID :
|
|
hspi->TxHalfCpltCallback = pCallback;
|
|
break;
|
|
|
|
case HAL_SPI_RX_HALF_COMPLETE_CB_ID :
|
|
hspi->RxHalfCpltCallback = pCallback;
|
|
break;
|
|
|
|
case HAL_SPI_TX_RX_HALF_COMPLETE_CB_ID :
|
|
hspi->TxRxHalfCpltCallback = pCallback;
|
|
break;
|
|
|
|
case HAL_SPI_ERROR_CB_ID :
|
|
hspi->ErrorCallback = pCallback;
|
|
break;
|
|
|
|
case HAL_SPI_ABORT_CB_ID :
|
|
hspi->AbortCpltCallback = pCallback;
|
|
break;
|
|
|
|
case HAL_SPI_MSPINIT_CB_ID :
|
|
hspi->MspInitCallback = pCallback;
|
|
break;
|
|
|
|
case HAL_SPI_MSPDEINIT_CB_ID :
|
|
hspi->MspDeInitCallback = pCallback;
|
|
break;
|
|
|
|
default :
|
|
/* Update the error code */
|
|
SET_BIT(hspi->ErrorCode, HAL_SPI_ERROR_INVALID_CALLBACK);
|
|
|
|
/* Return error status */
|
|
status = HAL_ERROR;
|
|
break;
|
|
}
|
|
}
|
|
else if (HAL_SPI_STATE_RESET == hspi->State)
|
|
{
|
|
switch (CallbackID)
|
|
{
|
|
case HAL_SPI_MSPINIT_CB_ID :
|
|
hspi->MspInitCallback = pCallback;
|
|
break;
|
|
|
|
case HAL_SPI_MSPDEINIT_CB_ID :
|
|
hspi->MspDeInitCallback = pCallback;
|
|
break;
|
|
|
|
default :
|
|
/* Update the error code */
|
|
SET_BIT(hspi->ErrorCode, HAL_SPI_ERROR_INVALID_CALLBACK);
|
|
|
|
/* Return error status */
|
|
status = HAL_ERROR;
|
|
break;
|
|
}
|
|
}
|
|
else
|
|
{
|
|
/* Update the error code */
|
|
SET_BIT(hspi->ErrorCode, HAL_SPI_ERROR_INVALID_CALLBACK);
|
|
|
|
/* Return error status */
|
|
status = HAL_ERROR;
|
|
}
|
|
|
|
/* Release Lock */
|
|
__HAL_UNLOCK(hspi);
|
|
return status;
|
|
}
|
|
|
|
/**
|
|
* @brief Unregister an SPI Callback
|
|
* SPI callback is redirected to the weak predefined callback
|
|
* @param hspi Pointer to a SPI_HandleTypeDef structure that contains
|
|
* the configuration information for the specified SPI.
|
|
* @param CallbackID ID of the callback to be unregistered
|
|
* @retval HAL status
|
|
*/
|
|
HAL_StatusTypeDef HAL_SPI_UnRegisterCallback(SPI_HandleTypeDef *hspi, HAL_SPI_CallbackIDTypeDef CallbackID)
|
|
{
|
|
HAL_StatusTypeDef status = HAL_OK;
|
|
|
|
/* Process locked */
|
|
__HAL_LOCK(hspi);
|
|
|
|
if (HAL_SPI_STATE_READY == hspi->State)
|
|
{
|
|
switch (CallbackID)
|
|
{
|
|
case HAL_SPI_TX_COMPLETE_CB_ID :
|
|
hspi->TxCpltCallback = HAL_SPI_TxCpltCallback; /* Legacy weak TxCpltCallback */
|
|
break;
|
|
|
|
case HAL_SPI_RX_COMPLETE_CB_ID :
|
|
hspi->RxCpltCallback = HAL_SPI_RxCpltCallback; /* Legacy weak RxCpltCallback */
|
|
break;
|
|
|
|
case HAL_SPI_TX_RX_COMPLETE_CB_ID :
|
|
hspi->TxRxCpltCallback = HAL_SPI_TxRxCpltCallback; /* Legacy weak TxRxCpltCallback */
|
|
break;
|
|
|
|
case HAL_SPI_TX_HALF_COMPLETE_CB_ID :
|
|
hspi->TxHalfCpltCallback = HAL_SPI_TxHalfCpltCallback; /* Legacy weak TxHalfCpltCallback */
|
|
break;
|
|
|
|
case HAL_SPI_RX_HALF_COMPLETE_CB_ID :
|
|
hspi->RxHalfCpltCallback = HAL_SPI_RxHalfCpltCallback; /* Legacy weak RxHalfCpltCallback */
|
|
break;
|
|
|
|
case HAL_SPI_TX_RX_HALF_COMPLETE_CB_ID :
|
|
hspi->TxRxHalfCpltCallback = HAL_SPI_TxRxHalfCpltCallback; /* Legacy weak TxRxHalfCpltCallback */
|
|
break;
|
|
|
|
case HAL_SPI_ERROR_CB_ID :
|
|
hspi->ErrorCallback = HAL_SPI_ErrorCallback; /* Legacy weak ErrorCallback */
|
|
break;
|
|
|
|
case HAL_SPI_ABORT_CB_ID :
|
|
hspi->AbortCpltCallback = HAL_SPI_AbortCpltCallback; /* Legacy weak AbortCpltCallback */
|
|
break;
|
|
|
|
case HAL_SPI_MSPINIT_CB_ID :
|
|
hspi->MspInitCallback = HAL_SPI_MspInit; /* Legacy weak MspInit */
|
|
break;
|
|
|
|
case HAL_SPI_MSPDEINIT_CB_ID :
|
|
hspi->MspDeInitCallback = HAL_SPI_MspDeInit; /* Legacy weak MspDeInit */
|
|
break;
|
|
|
|
default :
|
|
/* Update the error code */
|
|
SET_BIT(hspi->ErrorCode, HAL_SPI_ERROR_INVALID_CALLBACK);
|
|
|
|
/* Return error status */
|
|
status = HAL_ERROR;
|
|
break;
|
|
}
|
|
}
|
|
else if (HAL_SPI_STATE_RESET == hspi->State)
|
|
{
|
|
switch (CallbackID)
|
|
{
|
|
case HAL_SPI_MSPINIT_CB_ID :
|
|
hspi->MspInitCallback = HAL_SPI_MspInit; /* Legacy weak MspInit */
|
|
break;
|
|
|
|
case HAL_SPI_MSPDEINIT_CB_ID :
|
|
hspi->MspDeInitCallback = HAL_SPI_MspDeInit; /* Legacy weak MspDeInit */
|
|
break;
|
|
|
|
default :
|
|
/* Update the error code */
|
|
SET_BIT(hspi->ErrorCode, HAL_SPI_ERROR_INVALID_CALLBACK);
|
|
|
|
/* Return error status */
|
|
status = HAL_ERROR;
|
|
break;
|
|
}
|
|
}
|
|
else
|
|
{
|
|
/* Update the error code */
|
|
SET_BIT(hspi->ErrorCode, HAL_SPI_ERROR_INVALID_CALLBACK);
|
|
|
|
/* Return error status */
|
|
status = HAL_ERROR;
|
|
}
|
|
|
|
/* Release Lock */
|
|
__HAL_UNLOCK(hspi);
|
|
return status;
|
|
}
|
|
#endif /* USE_HAL_SPI_REGISTER_CALLBACKS */
|
|
/**
|
|
* @}
|
|
*/
|
|
|
|
/** @defgroup SPI_Exported_Functions_Group2 IO operation functions
|
|
* @brief Data transfers functions
|
|
*
|
|
@verbatim
|
|
==============================================================================
|
|
##### IO operation functions #####
|
|
===============================================================================
|
|
[..]
|
|
This subsection provides a set of functions allowing to manage the SPI
|
|
data transfers.
|
|
|
|
[..] The SPI supports master and slave mode :
|
|
|
|
(#) There are two modes of transfer:
|
|
(++) Blocking mode: The communication is performed in polling mode.
|
|
The HAL status of all data processing is returned by the same function
|
|
after finishing transfer.
|
|
(++) No-Blocking mode: The communication is performed using Interrupts
|
|
or DMA, These APIs return the HAL status.
|
|
The end of the data processing will be indicated through the
|
|
dedicated SPI IRQ when using Interrupt mode or the DMA IRQ when
|
|
using DMA mode.
|
|
The HAL_SPI_TxCpltCallback(), HAL_SPI_RxCpltCallback() and HAL_SPI_TxRxCpltCallback() user callbacks
|
|
will be executed respectively at the end of the transmit or Receive process
|
|
The HAL_SPI_ErrorCallback()user callback will be executed when a communication error is detected
|
|
|
|
(#) APIs provided for these 2 transfer modes (Blocking mode or Non blocking mode using either Interrupt or DMA)
|
|
exist for 1Line (simplex) and 2Lines (full duplex) modes.
|
|
|
|
@endverbatim
|
|
* @{
|
|
*/
|
|
|
|
/**
|
|
* @brief Transmit an amount of data in blocking mode.
|
|
* @param hspi pointer to a SPI_HandleTypeDef structure that contains
|
|
* the configuration information for SPI module.
|
|
* @param pData pointer to data buffer
|
|
* @param Size amount of data to be sent
|
|
* @param Timeout Timeout duration
|
|
* @retval HAL status
|
|
*/
|
|
HAL_StatusTypeDef HAL_SPI_Transmit(SPI_HandleTypeDef *hspi, uint8_t *pData, uint16_t Size, uint32_t Timeout)
|
|
{
|
|
uint32_t tickstart;
|
|
HAL_StatusTypeDef errorcode = HAL_OK;
|
|
uint16_t initial_TxXferCount;
|
|
|
|
/* Check Direction parameter */
|
|
assert_param(IS_SPI_DIRECTION_2LINES_OR_1LINE(hspi->Init.Direction));
|
|
|
|
/* Process Locked */
|
|
__HAL_LOCK(hspi);
|
|
|
|
/* Init tickstart for timeout management*/
|
|
tickstart = HAL_GetTick();
|
|
initial_TxXferCount = Size;
|
|
|
|
if (hspi->State != HAL_SPI_STATE_READY)
|
|
{
|
|
errorcode = HAL_BUSY;
|
|
goto error;
|
|
}
|
|
|
|
if ((pData == NULL) || (Size == 0U))
|
|
{
|
|
errorcode = HAL_ERROR;
|
|
goto error;
|
|
}
|
|
|
|
/* Set the transaction information */
|
|
hspi->State = HAL_SPI_STATE_BUSY_TX;
|
|
hspi->ErrorCode = HAL_SPI_ERROR_NONE;
|
|
hspi->pTxBuffPtr = (uint8_t *)pData;
|
|
hspi->TxXferSize = Size;
|
|
hspi->TxXferCount = Size;
|
|
|
|
/*Init field not used in handle to zero */
|
|
hspi->pRxBuffPtr = (uint8_t *)NULL;
|
|
hspi->RxXferSize = 0U;
|
|
hspi->RxXferCount = 0U;
|
|
hspi->TxISR = NULL;
|
|
hspi->RxISR = NULL;
|
|
|
|
/* Configure communication direction : 1Line */
|
|
if (hspi->Init.Direction == SPI_DIRECTION_1LINE)
|
|
{
|
|
/* Disable SPI Peripheral before set 1Line direction (BIDIOE bit) */
|
|
__HAL_SPI_DISABLE(hspi);
|
|
SPI_1LINE_TX(hspi);
|
|
}
|
|
|
|
#if (USE_SPI_CRC != 0U)
|
|
/* Reset CRC Calculation */
|
|
if (hspi->Init.CRCCalculation == SPI_CRCCALCULATION_ENABLE)
|
|
{
|
|
SPI_RESET_CRC(hspi);
|
|
}
|
|
#endif /* USE_SPI_CRC */
|
|
|
|
/* Check if the SPI is already enabled */
|
|
if ((hspi->Instance->CR1 & SPI_CR1_SPE) != SPI_CR1_SPE)
|
|
{
|
|
/* Enable SPI peripheral */
|
|
__HAL_SPI_ENABLE(hspi);
|
|
}
|
|
|
|
/* Transmit data in 16 Bit mode */
|
|
if (hspi->Init.DataSize > SPI_DATASIZE_8BIT)
|
|
{
|
|
if ((hspi->Init.Mode == SPI_MODE_SLAVE) || (initial_TxXferCount == 0x01U))
|
|
{
|
|
hspi->Instance->DR = *((uint16_t *)hspi->pTxBuffPtr);
|
|
hspi->pTxBuffPtr += sizeof(uint16_t);
|
|
hspi->TxXferCount--;
|
|
}
|
|
/* Transmit data in 16 Bit mode */
|
|
while (hspi->TxXferCount > 0U)
|
|
{
|
|
/* Wait until TXE flag is set to send data */
|
|
if (__HAL_SPI_GET_FLAG(hspi, SPI_FLAG_TXE))
|
|
{
|
|
hspi->Instance->DR = *((uint16_t *)hspi->pTxBuffPtr);
|
|
hspi->pTxBuffPtr += sizeof(uint16_t);
|
|
hspi->TxXferCount--;
|
|
}
|
|
else
|
|
{
|
|
/* Timeout management */
|
|
if ((((HAL_GetTick() - tickstart) >= Timeout) && (Timeout != HAL_MAX_DELAY)) || (Timeout == 0U))
|
|
{
|
|
errorcode = HAL_TIMEOUT;
|
|
hspi->State = HAL_SPI_STATE_READY;
|
|
goto error;
|
|
}
|
|
}
|
|
}
|
|
}
|
|
/* Transmit data in 8 Bit mode */
|
|
else
|
|
{
|
|
if ((hspi->Init.Mode == SPI_MODE_SLAVE) || (initial_TxXferCount == 0x01U))
|
|
{
|
|
if (hspi->TxXferCount > 1U)
|
|
{
|
|
/* write on the data register in packing mode */
|
|
hspi->Instance->DR = *((uint16_t *)hspi->pTxBuffPtr);
|
|
hspi->pTxBuffPtr += sizeof(uint16_t);
|
|
hspi->TxXferCount -= 2U;
|
|
}
|
|
else
|
|
{
|
|
*((__IO uint8_t *)&hspi->Instance->DR) = (*hspi->pTxBuffPtr);
|
|
hspi->pTxBuffPtr ++;
|
|
hspi->TxXferCount--;
|
|
}
|
|
}
|
|
while (hspi->TxXferCount > 0U)
|
|
{
|
|
/* Wait until TXE flag is set to send data */
|
|
if (__HAL_SPI_GET_FLAG(hspi, SPI_FLAG_TXE))
|
|
{
|
|
if (hspi->TxXferCount > 1U)
|
|
{
|
|
/* write on the data register in packing mode */
|
|
hspi->Instance->DR = *((uint16_t *)hspi->pTxBuffPtr);
|
|
hspi->pTxBuffPtr += sizeof(uint16_t);
|
|
hspi->TxXferCount -= 2U;
|
|
}
|
|
else
|
|
{
|
|
*((__IO uint8_t *)&hspi->Instance->DR) = (*hspi->pTxBuffPtr);
|
|
hspi->pTxBuffPtr++;
|
|
hspi->TxXferCount--;
|
|
}
|
|
}
|
|
else
|
|
{
|
|
/* Timeout management */
|
|
if ((((HAL_GetTick() - tickstart) >= Timeout) && (Timeout != HAL_MAX_DELAY)) || (Timeout == 0U))
|
|
{
|
|
errorcode = HAL_TIMEOUT;
|
|
hspi->State = HAL_SPI_STATE_READY;
|
|
goto error;
|
|
}
|
|
}
|
|
}
|
|
}
|
|
#if (USE_SPI_CRC != 0U)
|
|
/* Enable CRC Transmission */
|
|
if (hspi->Init.CRCCalculation == SPI_CRCCALCULATION_ENABLE)
|
|
{
|
|
SET_BIT(hspi->Instance->CR1, SPI_CR1_CRCNEXT);
|
|
}
|
|
#endif /* USE_SPI_CRC */
|
|
|
|
/* Check the end of the transaction */
|
|
if (SPI_EndRxTxTransaction(hspi, Timeout, tickstart) != HAL_OK)
|
|
{
|
|
hspi->ErrorCode = HAL_SPI_ERROR_FLAG;
|
|
}
|
|
|
|
/* Clear overrun flag in 2 Lines communication mode because received is not read */
|
|
if (hspi->Init.Direction == SPI_DIRECTION_2LINES)
|
|
{
|
|
__HAL_SPI_CLEAR_OVRFLAG(hspi);
|
|
}
|
|
|
|
if (hspi->ErrorCode != HAL_SPI_ERROR_NONE)
|
|
{
|
|
errorcode = HAL_ERROR;
|
|
}
|
|
else
|
|
{
|
|
hspi->State = HAL_SPI_STATE_READY;
|
|
}
|
|
|
|
error:
|
|
/* Process Unlocked */
|
|
__HAL_UNLOCK(hspi);
|
|
return errorcode;
|
|
}
|
|
|
|
/**
|
|
* @brief Receive an amount of data in blocking mode.
|
|
* @param hspi pointer to a SPI_HandleTypeDef structure that contains
|
|
* the configuration information for SPI module.
|
|
* @param pData pointer to data buffer
|
|
* @param Size amount of data to be received
|
|
* @param Timeout Timeout duration
|
|
* @retval HAL status
|
|
*/
|
|
HAL_StatusTypeDef HAL_SPI_Receive(SPI_HandleTypeDef *hspi, uint8_t *pData, uint16_t Size, uint32_t Timeout)
|
|
{
|
|
#if (USE_SPI_CRC != 0U)
|
|
__IO uint32_t tmpreg = 0U;
|
|
__IO uint8_t *ptmpreg8;
|
|
__IO uint8_t tmpreg8 = 0;
|
|
#endif /* USE_SPI_CRC */
|
|
uint32_t tickstart;
|
|
HAL_StatusTypeDef errorcode = HAL_OK;
|
|
|
|
if (hspi->State != HAL_SPI_STATE_READY)
|
|
{
|
|
errorcode = HAL_BUSY;
|
|
goto error;
|
|
}
|
|
|
|
if ((hspi->Init.Mode == SPI_MODE_MASTER) && (hspi->Init.Direction == SPI_DIRECTION_2LINES))
|
|
{
|
|
hspi->State = HAL_SPI_STATE_BUSY_RX;
|
|
/* Call transmit-receive function to send Dummy data on Tx line and generate clock on CLK line */
|
|
return HAL_SPI_TransmitReceive(hspi, pData, pData, Size, Timeout);
|
|
}
|
|
|
|
/* Process Locked */
|
|
__HAL_LOCK(hspi);
|
|
|
|
/* Init tickstart for timeout management*/
|
|
tickstart = HAL_GetTick();
|
|
|
|
if ((pData == NULL) || (Size == 0U))
|
|
{
|
|
errorcode = HAL_ERROR;
|
|
goto error;
|
|
}
|
|
|
|
/* Set the transaction information */
|
|
hspi->State = HAL_SPI_STATE_BUSY_RX;
|
|
hspi->ErrorCode = HAL_SPI_ERROR_NONE;
|
|
hspi->pRxBuffPtr = (uint8_t *)pData;
|
|
hspi->RxXferSize = Size;
|
|
hspi->RxXferCount = Size;
|
|
|
|
/*Init field not used in handle to zero */
|
|
hspi->pTxBuffPtr = (uint8_t *)NULL;
|
|
hspi->TxXferSize = 0U;
|
|
hspi->TxXferCount = 0U;
|
|
hspi->RxISR = NULL;
|
|
hspi->TxISR = NULL;
|
|
|
|
#if (USE_SPI_CRC != 0U)
|
|
/* Reset CRC Calculation */
|
|
if (hspi->Init.CRCCalculation == SPI_CRCCALCULATION_ENABLE)
|
|
{
|
|
SPI_RESET_CRC(hspi);
|
|
/* this is done to handle the CRCNEXT before the latest data */
|
|
hspi->RxXferCount--;
|
|
}
|
|
#endif /* USE_SPI_CRC */
|
|
|
|
/* Set the Rx Fifo threshold */
|
|
if (hspi->Init.DataSize > SPI_DATASIZE_8BIT)
|
|
{
|
|
/* Set RX Fifo threshold according the reception data length: 16bit */
|
|
CLEAR_BIT(hspi->Instance->CR2, SPI_RXFIFO_THRESHOLD);
|
|
}
|
|
else
|
|
{
|
|
/* Set RX Fifo threshold according the reception data length: 8bit */
|
|
SET_BIT(hspi->Instance->CR2, SPI_RXFIFO_THRESHOLD);
|
|
}
|
|
|
|
/* Configure communication direction: 1Line */
|
|
if (hspi->Init.Direction == SPI_DIRECTION_1LINE)
|
|
{
|
|
/* Disable SPI Peripheral before set 1Line direction (BIDIOE bit) */
|
|
__HAL_SPI_DISABLE(hspi);
|
|
SPI_1LINE_RX(hspi);
|
|
}
|
|
|
|
/* Check if the SPI is already enabled */
|
|
if ((hspi->Instance->CR1 & SPI_CR1_SPE) != SPI_CR1_SPE)
|
|
{
|
|
/* Enable SPI peripheral */
|
|
__HAL_SPI_ENABLE(hspi);
|
|
}
|
|
|
|
/* Receive data in 8 Bit mode */
|
|
if (hspi->Init.DataSize <= SPI_DATASIZE_8BIT)
|
|
{
|
|
/* Transfer loop */
|
|
while (hspi->RxXferCount > 0U)
|
|
{
|
|
/* Check the RXNE flag */
|
|
if (__HAL_SPI_GET_FLAG(hspi, SPI_FLAG_RXNE))
|
|
{
|
|
/* read the received data */
|
|
(* (uint8_t *)hspi->pRxBuffPtr) = *(__IO uint8_t *)&hspi->Instance->DR;
|
|
hspi->pRxBuffPtr += sizeof(uint8_t);
|
|
hspi->RxXferCount--;
|
|
}
|
|
else
|
|
{
|
|
/* Timeout management */
|
|
if ((((HAL_GetTick() - tickstart) >= Timeout) && (Timeout != HAL_MAX_DELAY)) || (Timeout == 0U))
|
|
{
|
|
errorcode = HAL_TIMEOUT;
|
|
hspi->State = HAL_SPI_STATE_READY;
|
|
goto error;
|
|
}
|
|
}
|
|
}
|
|
}
|
|
else
|
|
{
|
|
/* Transfer loop */
|
|
while (hspi->RxXferCount > 0U)
|
|
{
|
|
/* Check the RXNE flag */
|
|
if (__HAL_SPI_GET_FLAG(hspi, SPI_FLAG_RXNE))
|
|
{
|
|
*((uint16_t *)hspi->pRxBuffPtr) = (uint16_t)hspi->Instance->DR;
|
|
hspi->pRxBuffPtr += sizeof(uint16_t);
|
|
hspi->RxXferCount--;
|
|
}
|
|
else
|
|
{
|
|
/* Timeout management */
|
|
if ((((HAL_GetTick() - tickstart) >= Timeout) && (Timeout != HAL_MAX_DELAY)) || (Timeout == 0U))
|
|
{
|
|
errorcode = HAL_TIMEOUT;
|
|
hspi->State = HAL_SPI_STATE_READY;
|
|
goto error;
|
|
}
|
|
}
|
|
}
|
|
}
|
|
|
|
#if (USE_SPI_CRC != 0U)
|
|
/* Handle the CRC Transmission */
|
|
if (hspi->Init.CRCCalculation == SPI_CRCCALCULATION_ENABLE)
|
|
{
|
|
/* freeze the CRC before the latest data */
|
|
SET_BIT(hspi->Instance->CR1, SPI_CR1_CRCNEXT);
|
|
|
|
/* Read the latest data */
|
|
if (SPI_WaitFlagStateUntilTimeout(hspi, SPI_FLAG_RXNE, SET, Timeout, tickstart) != HAL_OK)
|
|
{
|
|
/* the latest data has not been received */
|
|
errorcode = HAL_TIMEOUT;
|
|
goto error;
|
|
}
|
|
|
|
/* Receive last data in 16 Bit mode */
|
|
if (hspi->Init.DataSize > SPI_DATASIZE_8BIT)
|
|
{
|
|
*((uint16_t *)hspi->pRxBuffPtr) = (uint16_t)hspi->Instance->DR;
|
|
}
|
|
/* Receive last data in 8 Bit mode */
|
|
else
|
|
{
|
|
(*(uint8_t *)hspi->pRxBuffPtr) = *(__IO uint8_t *)&hspi->Instance->DR;
|
|
}
|
|
|
|
/* Wait the CRC data */
|
|
if (SPI_WaitFlagStateUntilTimeout(hspi, SPI_FLAG_RXNE, SET, Timeout, tickstart) != HAL_OK)
|
|
{
|
|
SET_BIT(hspi->ErrorCode, HAL_SPI_ERROR_CRC);
|
|
errorcode = HAL_TIMEOUT;
|
|
goto error;
|
|
}
|
|
|
|
/* Read CRC to Flush DR and RXNE flag */
|
|
if (hspi->Init.DataSize == SPI_DATASIZE_16BIT)
|
|
{
|
|
/* Read 16bit CRC */
|
|
tmpreg = READ_REG(hspi->Instance->DR);
|
|
/* To avoid GCC warning */
|
|
UNUSED(tmpreg);
|
|
}
|
|
else
|
|
{
|
|
/* Initialize the 8bit temporary pointer */
|
|
ptmpreg8 = (__IO uint8_t *)&hspi->Instance->DR;
|
|
/* Read 8bit CRC */
|
|
tmpreg8 = *ptmpreg8;
|
|
/* To avoid GCC warning */
|
|
UNUSED(tmpreg8);
|
|
|
|
if ((hspi->Init.DataSize == SPI_DATASIZE_8BIT) && (hspi->Init.CRCLength == SPI_CRC_LENGTH_16BIT))
|
|
{
|
|
if (SPI_WaitFlagStateUntilTimeout(hspi, SPI_FLAG_RXNE, SET, Timeout, tickstart) != HAL_OK)
|
|
{
|
|
/* Error on the CRC reception */
|
|
SET_BIT(hspi->ErrorCode, HAL_SPI_ERROR_CRC);
|
|
errorcode = HAL_TIMEOUT;
|
|
goto error;
|
|
}
|
|
/* Read 8bit CRC again in case of 16bit CRC in 8bit Data mode */
|
|
tmpreg8 = *ptmpreg8;
|
|
/* To avoid GCC warning */
|
|
UNUSED(tmpreg8);
|
|
}
|
|
}
|
|
}
|
|
#endif /* USE_SPI_CRC */
|
|
|
|
/* Check the end of the transaction */
|
|
if (SPI_EndRxTransaction(hspi, Timeout, tickstart) != HAL_OK)
|
|
{
|
|
hspi->ErrorCode = HAL_SPI_ERROR_FLAG;
|
|
}
|
|
|
|
#if (USE_SPI_CRC != 0U)
|
|
/* Check if CRC error occurred */
|
|
if (__HAL_SPI_GET_FLAG(hspi, SPI_FLAG_CRCERR))
|
|
{
|
|
SET_BIT(hspi->ErrorCode, HAL_SPI_ERROR_CRC);
|
|
__HAL_SPI_CLEAR_CRCERRFLAG(hspi);
|
|
}
|
|
#endif /* USE_SPI_CRC */
|
|
|
|
if (hspi->ErrorCode != HAL_SPI_ERROR_NONE)
|
|
{
|
|
errorcode = HAL_ERROR;
|
|
}
|
|
else
|
|
{
|
|
hspi->State = HAL_SPI_STATE_READY;
|
|
}
|
|
|
|
error :
|
|
__HAL_UNLOCK(hspi);
|
|
return errorcode;
|
|
}
|
|
|
|
/**
|
|
* @brief Transmit and Receive an amount of data in blocking mode.
|
|
* @param hspi pointer to a SPI_HandleTypeDef structure that contains
|
|
* the configuration information for SPI module.
|
|
* @param pTxData pointer to transmission data buffer
|
|
* @param pRxData pointer to reception data buffer
|
|
* @param Size amount of data to be sent and received
|
|
* @param Timeout Timeout duration
|
|
* @retval HAL status
|
|
*/
|
|
HAL_StatusTypeDef HAL_SPI_TransmitReceive(SPI_HandleTypeDef *hspi, uint8_t *pTxData, uint8_t *pRxData, uint16_t Size,
|
|
uint32_t Timeout)
|
|
{
|
|
uint16_t initial_TxXferCount;
|
|
uint16_t initial_RxXferCount;
|
|
uint32_t tmp_mode;
|
|
HAL_SPI_StateTypeDef tmp_state;
|
|
uint32_t tickstart;
|
|
#if (USE_SPI_CRC != 0U)
|
|
__IO uint32_t tmpreg = 0U;
|
|
uint32_t spi_cr1;
|
|
uint32_t spi_cr2;
|
|
__IO uint8_t *ptmpreg8;
|
|
__IO uint8_t tmpreg8 = 0;
|
|
#endif /* USE_SPI_CRC */
|
|
|
|
/* Variable used to alternate Rx and Tx during transfer */
|
|
uint32_t txallowed = 1U;
|
|
HAL_StatusTypeDef errorcode = HAL_OK;
|
|
|
|
/* Check Direction parameter */
|
|
assert_param(IS_SPI_DIRECTION_2LINES(hspi->Init.Direction));
|
|
|
|
/* Process Locked */
|
|
__HAL_LOCK(hspi);
|
|
|
|
/* Init tickstart for timeout management*/
|
|
tickstart = HAL_GetTick();
|
|
|
|
/* Init temporary variables */
|
|
tmp_state = hspi->State;
|
|
tmp_mode = hspi->Init.Mode;
|
|
initial_TxXferCount = Size;
|
|
initial_RxXferCount = Size;
|
|
#if (USE_SPI_CRC != 0U)
|
|
spi_cr1 = READ_REG(hspi->Instance->CR1);
|
|
spi_cr2 = READ_REG(hspi->Instance->CR2);
|
|
#endif /* USE_SPI_CRC */
|
|
|
|
if (!((tmp_state == HAL_SPI_STATE_READY) || \
|
|
((tmp_mode == SPI_MODE_MASTER) && (hspi->Init.Direction == SPI_DIRECTION_2LINES) && (tmp_state == HAL_SPI_STATE_BUSY_RX))))
|
|
{
|
|
errorcode = HAL_BUSY;
|
|
goto error;
|
|
}
|
|
|
|
if ((pTxData == NULL) || (pRxData == NULL) || (Size == 0U))
|
|
{
|
|
errorcode = HAL_ERROR;
|
|
goto error;
|
|
}
|
|
|
|
/* Don't overwrite in case of HAL_SPI_STATE_BUSY_RX */
|
|
if (hspi->State != HAL_SPI_STATE_BUSY_RX)
|
|
{
|
|
hspi->State = HAL_SPI_STATE_BUSY_TX_RX;
|
|
}
|
|
|
|
/* Set the transaction information */
|
|
hspi->ErrorCode = HAL_SPI_ERROR_NONE;
|
|
hspi->pRxBuffPtr = (uint8_t *)pRxData;
|
|
hspi->RxXferCount = Size;
|
|
hspi->RxXferSize = Size;
|
|
hspi->pTxBuffPtr = (uint8_t *)pTxData;
|
|
hspi->TxXferCount = Size;
|
|
hspi->TxXferSize = Size;
|
|
|
|
/*Init field not used in handle to zero */
|
|
hspi->RxISR = NULL;
|
|
hspi->TxISR = NULL;
|
|
|
|
#if (USE_SPI_CRC != 0U)
|
|
/* Reset CRC Calculation */
|
|
if (hspi->Init.CRCCalculation == SPI_CRCCALCULATION_ENABLE)
|
|
{
|
|
SPI_RESET_CRC(hspi);
|
|
}
|
|
#endif /* USE_SPI_CRC */
|
|
|
|
/* Set the Rx Fifo threshold */
|
|
if ((hspi->Init.DataSize > SPI_DATASIZE_8BIT) || (initial_RxXferCount > 1U))
|
|
{
|
|
/* Set fiforxthreshold according the reception data length: 16bit */
|
|
CLEAR_BIT(hspi->Instance->CR2, SPI_RXFIFO_THRESHOLD);
|
|
}
|
|
else
|
|
{
|
|
/* Set fiforxthreshold according the reception data length: 8bit */
|
|
SET_BIT(hspi->Instance->CR2, SPI_RXFIFO_THRESHOLD);
|
|
}
|
|
|
|
/* Check if the SPI is already enabled */
|
|
if ((hspi->Instance->CR1 & SPI_CR1_SPE) != SPI_CR1_SPE)
|
|
{
|
|
/* Enable SPI peripheral */
|
|
__HAL_SPI_ENABLE(hspi);
|
|
}
|
|
|
|
/* Transmit and Receive data in 16 Bit mode */
|
|
if (hspi->Init.DataSize > SPI_DATASIZE_8BIT)
|
|
{
|
|
if ((hspi->Init.Mode == SPI_MODE_SLAVE) || (initial_TxXferCount == 0x01U))
|
|
{
|
|
hspi->Instance->DR = *((uint16_t *)hspi->pTxBuffPtr);
|
|
hspi->pTxBuffPtr += sizeof(uint16_t);
|
|
hspi->TxXferCount--;
|
|
|
|
#if (USE_SPI_CRC != 0U)
|
|
/* Enable CRC Transmission */
|
|
if ((hspi->TxXferCount == 0U) && (hspi->Init.CRCCalculation == SPI_CRCCALCULATION_ENABLE))
|
|
{
|
|
/* Set NSS Soft to received correctly the CRC on slave mode with NSS pulse activated */
|
|
if ((READ_BIT(spi_cr1, SPI_CR1_MSTR) == 0U) && (READ_BIT(spi_cr2, SPI_CR2_NSSP) == SPI_CR2_NSSP))
|
|
{
|
|
SET_BIT(hspi->Instance->CR1, SPI_CR1_SSM);
|
|
}
|
|
SET_BIT(hspi->Instance->CR1, SPI_CR1_CRCNEXT);
|
|
}
|
|
#endif /* USE_SPI_CRC */
|
|
|
|
}
|
|
while ((hspi->TxXferCount > 0U) || (hspi->RxXferCount > 0U))
|
|
{
|
|
/* Check TXE flag */
|
|
if ((__HAL_SPI_GET_FLAG(hspi, SPI_FLAG_TXE)) && (hspi->TxXferCount > 0U) && (txallowed == 1U))
|
|
{
|
|
hspi->Instance->DR = *((uint16_t *)hspi->pTxBuffPtr);
|
|
hspi->pTxBuffPtr += sizeof(uint16_t);
|
|
hspi->TxXferCount--;
|
|
/* Next Data is a reception (Rx). Tx not allowed */
|
|
txallowed = 0U;
|
|
|
|
#if (USE_SPI_CRC != 0U)
|
|
/* Enable CRC Transmission */
|
|
if ((hspi->TxXferCount == 0U) && (hspi->Init.CRCCalculation == SPI_CRCCALCULATION_ENABLE))
|
|
{
|
|
/* Set NSS Soft to received correctly the CRC on slave mode with NSS pulse activated */
|
|
if ((READ_BIT(spi_cr1, SPI_CR1_MSTR) == 0U) && (READ_BIT(spi_cr2, SPI_CR2_NSSP) == SPI_CR2_NSSP))
|
|
{
|
|
SET_BIT(hspi->Instance->CR1, SPI_CR1_SSM);
|
|
}
|
|
SET_BIT(hspi->Instance->CR1, SPI_CR1_CRCNEXT);
|
|
}
|
|
#endif /* USE_SPI_CRC */
|
|
}
|
|
|
|
/* Check RXNE flag */
|
|
if ((__HAL_SPI_GET_FLAG(hspi, SPI_FLAG_RXNE)) && (hspi->RxXferCount > 0U))
|
|
{
|
|
*((uint16_t *)hspi->pRxBuffPtr) = (uint16_t)hspi->Instance->DR;
|
|
hspi->pRxBuffPtr += sizeof(uint16_t);
|
|
hspi->RxXferCount--;
|
|
/* Next Data is a Transmission (Tx). Tx is allowed */
|
|
txallowed = 1U;
|
|
}
|
|
if (((HAL_GetTick() - tickstart) >= Timeout) && (Timeout != HAL_MAX_DELAY))
|
|
{
|
|
errorcode = HAL_TIMEOUT;
|
|
hspi->State = HAL_SPI_STATE_READY;
|
|
goto error;
|
|
}
|
|
}
|
|
}
|
|
/* Transmit and Receive data in 8 Bit mode */
|
|
else
|
|
{
|
|
if ((hspi->Init.Mode == SPI_MODE_SLAVE) || (initial_TxXferCount == 0x01U))
|
|
{
|
|
if (hspi->TxXferCount > 1U)
|
|
{
|
|
hspi->Instance->DR = *((uint16_t *)hspi->pTxBuffPtr);
|
|
hspi->pTxBuffPtr += sizeof(uint16_t);
|
|
hspi->TxXferCount -= 2U;
|
|
}
|
|
else
|
|
{
|
|
*(__IO uint8_t *)&hspi->Instance->DR = (*hspi->pTxBuffPtr);
|
|
hspi->pTxBuffPtr++;
|
|
hspi->TxXferCount--;
|
|
|
|
#if (USE_SPI_CRC != 0U)
|
|
/* Enable CRC Transmission */
|
|
if ((hspi->TxXferCount == 0U) && (hspi->Init.CRCCalculation == SPI_CRCCALCULATION_ENABLE))
|
|
{
|
|
/* Set NSS Soft to received correctly the CRC on slave mode with NSS pulse activated */
|
|
if ((READ_BIT(spi_cr1, SPI_CR1_MSTR) == 0U) && (READ_BIT(spi_cr2, SPI_CR2_NSSP) == SPI_CR2_NSSP))
|
|
{
|
|
SET_BIT(hspi->Instance->CR1, SPI_CR1_SSM);
|
|
}
|
|
SET_BIT(hspi->Instance->CR1, SPI_CR1_CRCNEXT);
|
|
}
|
|
#endif /* USE_SPI_CRC */
|
|
}
|
|
}
|
|
while ((hspi->TxXferCount > 0U) || (hspi->RxXferCount > 0U))
|
|
{
|
|
/* Check TXE flag */
|
|
if ((__HAL_SPI_GET_FLAG(hspi, SPI_FLAG_TXE)) && (hspi->TxXferCount > 0U) && (txallowed == 1U))
|
|
{
|
|
if (hspi->TxXferCount > 1U)
|
|
{
|
|
hspi->Instance->DR = *((uint16_t *)hspi->pTxBuffPtr);
|
|
hspi->pTxBuffPtr += sizeof(uint16_t);
|
|
hspi->TxXferCount -= 2U;
|
|
}
|
|
else
|
|
{
|
|
*(__IO uint8_t *)&hspi->Instance->DR = (*hspi->pTxBuffPtr);
|
|
hspi->pTxBuffPtr++;
|
|
hspi->TxXferCount--;
|
|
}
|
|
/* Next Data is a reception (Rx). Tx not allowed */
|
|
txallowed = 0U;
|
|
|
|
#if (USE_SPI_CRC != 0U)
|
|
/* Enable CRC Transmission */
|
|
if ((hspi->TxXferCount == 0U) && (hspi->Init.CRCCalculation == SPI_CRCCALCULATION_ENABLE))
|
|
{
|
|
/* Set NSS Soft to received correctly the CRC on slave mode with NSS pulse activated */
|
|
if ((READ_BIT(spi_cr1, SPI_CR1_MSTR) == 0U) && (READ_BIT(spi_cr2, SPI_CR2_NSSP) == SPI_CR2_NSSP))
|
|
{
|
|
SET_BIT(hspi->Instance->CR1, SPI_CR1_SSM);
|
|
}
|
|
SET_BIT(hspi->Instance->CR1, SPI_CR1_CRCNEXT);
|
|
}
|
|
#endif /* USE_SPI_CRC */
|
|
}
|
|
|
|
/* Wait until RXNE flag is reset */
|
|
if ((__HAL_SPI_GET_FLAG(hspi, SPI_FLAG_RXNE)) && (hspi->RxXferCount > 0U))
|
|
{
|
|
if (hspi->RxXferCount > 1U)
|
|
{
|
|
*((uint16_t *)hspi->pRxBuffPtr) = (uint16_t)hspi->Instance->DR;
|
|
hspi->pRxBuffPtr += sizeof(uint16_t);
|
|
hspi->RxXferCount -= 2U;
|
|
if (hspi->RxXferCount <= 1U)
|
|
{
|
|
/* Set RX Fifo threshold before to switch on 8 bit data size */
|
|
SET_BIT(hspi->Instance->CR2, SPI_RXFIFO_THRESHOLD);
|
|
}
|
|
}
|
|
else
|
|
{
|
|
(*(uint8_t *)hspi->pRxBuffPtr) = *(__IO uint8_t *)&hspi->Instance->DR;
|
|
hspi->pRxBuffPtr++;
|
|
hspi->RxXferCount--;
|
|
}
|
|
/* Next Data is a Transmission (Tx). Tx is allowed */
|
|
txallowed = 1U;
|
|
}
|
|
if ((((HAL_GetTick() - tickstart) >= Timeout) && ((Timeout != HAL_MAX_DELAY))) || (Timeout == 0U))
|
|
{
|
|
errorcode = HAL_TIMEOUT;
|
|
hspi->State = HAL_SPI_STATE_READY;
|
|
goto error;
|
|
}
|
|
}
|
|
}
|
|
|
|
#if (USE_SPI_CRC != 0U)
|
|
/* Read CRC from DR to close CRC calculation process */
|
|
if (hspi->Init.CRCCalculation == SPI_CRCCALCULATION_ENABLE)
|
|
{
|
|
/* Wait until TXE flag */
|
|
if (SPI_WaitFlagStateUntilTimeout(hspi, SPI_FLAG_RXNE, SET, Timeout, tickstart) != HAL_OK)
|
|
{
|
|
/* Error on the CRC reception */
|
|
SET_BIT(hspi->ErrorCode, HAL_SPI_ERROR_CRC);
|
|
errorcode = HAL_TIMEOUT;
|
|
goto error;
|
|
}
|
|
/* Read CRC */
|
|
if (hspi->Init.DataSize == SPI_DATASIZE_16BIT)
|
|
{
|
|
/* Read 16bit CRC */
|
|
tmpreg = READ_REG(hspi->Instance->DR);
|
|
/* To avoid GCC warning */
|
|
UNUSED(tmpreg);
|
|
}
|
|
else
|
|
{
|
|
/* Initialize the 8bit temporary pointer */
|
|
ptmpreg8 = (__IO uint8_t *)&hspi->Instance->DR;
|
|
/* Read 8bit CRC */
|
|
tmpreg8 = *ptmpreg8;
|
|
/* To avoid GCC warning */
|
|
UNUSED(tmpreg8);
|
|
|
|
if (hspi->Init.CRCLength == SPI_CRC_LENGTH_16BIT)
|
|
{
|
|
if (SPI_WaitFlagStateUntilTimeout(hspi, SPI_FLAG_RXNE, SET, Timeout, tickstart) != HAL_OK)
|
|
{
|
|
/* Error on the CRC reception */
|
|
SET_BIT(hspi->ErrorCode, HAL_SPI_ERROR_CRC);
|
|
errorcode = HAL_TIMEOUT;
|
|
goto error;
|
|
}
|
|
/* Read 8bit CRC again in case of 16bit CRC in 8bit Data mode */
|
|
tmpreg8 = *ptmpreg8;
|
|
/* To avoid GCC warning */
|
|
UNUSED(tmpreg8);
|
|
}
|
|
}
|
|
}
|
|
|
|
/* Check if CRC error occurred */
|
|
if (__HAL_SPI_GET_FLAG(hspi, SPI_FLAG_CRCERR))
|
|
{
|
|
SET_BIT(hspi->ErrorCode, HAL_SPI_ERROR_CRC);
|
|
/* Clear CRC Flag */
|
|
__HAL_SPI_CLEAR_CRCERRFLAG(hspi);
|
|
|
|
errorcode = HAL_ERROR;
|
|
}
|
|
#endif /* USE_SPI_CRC */
|
|
|
|
/* Check the end of the transaction */
|
|
if (SPI_EndRxTxTransaction(hspi, Timeout, tickstart) != HAL_OK)
|
|
{
|
|
errorcode = HAL_ERROR;
|
|
hspi->ErrorCode = HAL_SPI_ERROR_FLAG;
|
|
}
|
|
|
|
if (hspi->ErrorCode != HAL_SPI_ERROR_NONE)
|
|
{
|
|
errorcode = HAL_ERROR;
|
|
}
|
|
else
|
|
{
|
|
hspi->State = HAL_SPI_STATE_READY;
|
|
}
|
|
|
|
error :
|
|
__HAL_UNLOCK(hspi);
|
|
return errorcode;
|
|
}
|
|
|
|
/**
|
|
* @brief Transmit an amount of data in non-blocking mode with Interrupt.
|
|
* @param hspi pointer to a SPI_HandleTypeDef structure that contains
|
|
* the configuration information for SPI module.
|
|
* @param pData pointer to data buffer
|
|
* @param Size amount of data to be sent
|
|
* @retval HAL status
|
|
*/
|
|
HAL_StatusTypeDef HAL_SPI_Transmit_IT(SPI_HandleTypeDef *hspi, uint8_t *pData, uint16_t Size)
|
|
{
|
|
HAL_StatusTypeDef errorcode = HAL_OK;
|
|
|
|
/* Check Direction parameter */
|
|
assert_param(IS_SPI_DIRECTION_2LINES_OR_1LINE(hspi->Init.Direction));
|
|
|
|
|
|
if ((pData == NULL) || (Size == 0U))
|
|
{
|
|
errorcode = HAL_ERROR;
|
|
goto error;
|
|
}
|
|
|
|
if (hspi->State != HAL_SPI_STATE_READY)
|
|
{
|
|
errorcode = HAL_BUSY;
|
|
goto error;
|
|
}
|
|
|
|
/* Process Locked */
|
|
__HAL_LOCK(hspi);
|
|
|
|
/* Set the transaction information */
|
|
hspi->State = HAL_SPI_STATE_BUSY_TX;
|
|
hspi->ErrorCode = HAL_SPI_ERROR_NONE;
|
|
hspi->pTxBuffPtr = (uint8_t *)pData;
|
|
hspi->TxXferSize = Size;
|
|
hspi->TxXferCount = Size;
|
|
|
|
/* Init field not used in handle to zero */
|
|
hspi->pRxBuffPtr = (uint8_t *)NULL;
|
|
hspi->RxXferSize = 0U;
|
|
hspi->RxXferCount = 0U;
|
|
hspi->RxISR = NULL;
|
|
|
|
/* Set the function for IT treatment */
|
|
if (hspi->Init.DataSize > SPI_DATASIZE_8BIT)
|
|
{
|
|
hspi->TxISR = SPI_TxISR_16BIT;
|
|
}
|
|
else
|
|
{
|
|
hspi->TxISR = SPI_TxISR_8BIT;
|
|
}
|
|
|
|
/* Configure communication direction : 1Line */
|
|
if (hspi->Init.Direction == SPI_DIRECTION_1LINE)
|
|
{
|
|
/* Disable SPI Peripheral before set 1Line direction (BIDIOE bit) */
|
|
__HAL_SPI_DISABLE(hspi);
|
|
SPI_1LINE_TX(hspi);
|
|
}
|
|
|
|
#if (USE_SPI_CRC != 0U)
|
|
/* Reset CRC Calculation */
|
|
if (hspi->Init.CRCCalculation == SPI_CRCCALCULATION_ENABLE)
|
|
{
|
|
SPI_RESET_CRC(hspi);
|
|
}
|
|
#endif /* USE_SPI_CRC */
|
|
|
|
/* Check if the SPI is already enabled */
|
|
if ((hspi->Instance->CR1 & SPI_CR1_SPE) != SPI_CR1_SPE)
|
|
{
|
|
/* Enable SPI peripheral */
|
|
__HAL_SPI_ENABLE(hspi);
|
|
}
|
|
|
|
/* Process Unlocked */
|
|
__HAL_UNLOCK(hspi);
|
|
/* Enable TXE and ERR interrupt */
|
|
__HAL_SPI_ENABLE_IT(hspi, (SPI_IT_TXE | SPI_IT_ERR));
|
|
|
|
error :
|
|
return errorcode;
|
|
}
|
|
|
|
/**
|
|
* @brief Receive an amount of data in non-blocking mode with Interrupt.
|
|
* @param hspi pointer to a SPI_HandleTypeDef structure that contains
|
|
* the configuration information for SPI module.
|
|
* @param pData pointer to data buffer
|
|
* @param Size amount of data to be sent
|
|
* @retval HAL status
|
|
*/
|
|
HAL_StatusTypeDef HAL_SPI_Receive_IT(SPI_HandleTypeDef *hspi, uint8_t *pData, uint16_t Size)
|
|
{
|
|
HAL_StatusTypeDef errorcode = HAL_OK;
|
|
|
|
|
|
if (hspi->State != HAL_SPI_STATE_READY)
|
|
{
|
|
errorcode = HAL_BUSY;
|
|
goto error;
|
|
}
|
|
|
|
if ((hspi->Init.Direction == SPI_DIRECTION_2LINES) && (hspi->Init.Mode == SPI_MODE_MASTER))
|
|
{
|
|
hspi->State = HAL_SPI_STATE_BUSY_RX;
|
|
/* Call transmit-receive function to send Dummy data on Tx line and generate clock on CLK line */
|
|
return HAL_SPI_TransmitReceive_IT(hspi, pData, pData, Size);
|
|
}
|
|
|
|
|
|
if ((pData == NULL) || (Size == 0U))
|
|
{
|
|
errorcode = HAL_ERROR;
|
|
goto error;
|
|
}
|
|
|
|
/* Process Locked */
|
|
__HAL_LOCK(hspi);
|
|
|
|
/* Set the transaction information */
|
|
hspi->State = HAL_SPI_STATE_BUSY_RX;
|
|
hspi->ErrorCode = HAL_SPI_ERROR_NONE;
|
|
hspi->pRxBuffPtr = (uint8_t *)pData;
|
|
hspi->RxXferSize = Size;
|
|
hspi->RxXferCount = Size;
|
|
|
|
/* Init field not used in handle to zero */
|
|
hspi->pTxBuffPtr = (uint8_t *)NULL;
|
|
hspi->TxXferSize = 0U;
|
|
hspi->TxXferCount = 0U;
|
|
hspi->TxISR = NULL;
|
|
|
|
/* Check the data size to adapt Rx threshold and the set the function for IT treatment */
|
|
if (hspi->Init.DataSize > SPI_DATASIZE_8BIT)
|
|
{
|
|
/* Set RX Fifo threshold according the reception data length: 16 bit */
|
|
CLEAR_BIT(hspi->Instance->CR2, SPI_RXFIFO_THRESHOLD);
|
|
hspi->RxISR = SPI_RxISR_16BIT;
|
|
}
|
|
else
|
|
{
|
|
/* Set RX Fifo threshold according the reception data length: 8 bit */
|
|
SET_BIT(hspi->Instance->CR2, SPI_RXFIFO_THRESHOLD);
|
|
hspi->RxISR = SPI_RxISR_8BIT;
|
|
}
|
|
|
|
/* Configure communication direction : 1Line */
|
|
if (hspi->Init.Direction == SPI_DIRECTION_1LINE)
|
|
{
|
|
/* Disable SPI Peripheral before set 1Line direction (BIDIOE bit) */
|
|
__HAL_SPI_DISABLE(hspi);
|
|
SPI_1LINE_RX(hspi);
|
|
}
|
|
|
|
#if (USE_SPI_CRC != 0U)
|
|
/* Reset CRC Calculation */
|
|
if (hspi->Init.CRCCalculation == SPI_CRCCALCULATION_ENABLE)
|
|
{
|
|
hspi->CRCSize = 1U;
|
|
if ((hspi->Init.DataSize <= SPI_DATASIZE_8BIT) && (hspi->Init.CRCLength == SPI_CRC_LENGTH_16BIT))
|
|
{
|
|
hspi->CRCSize = 2U;
|
|
}
|
|
SPI_RESET_CRC(hspi);
|
|
}
|
|
else
|
|
{
|
|
hspi->CRCSize = 0U;
|
|
}
|
|
#endif /* USE_SPI_CRC */
|
|
|
|
/* Note : The SPI must be enabled after unlocking current process
|
|
to avoid the risk of SPI interrupt handle execution before current
|
|
process unlock */
|
|
|
|
/* Check if the SPI is already enabled */
|
|
if ((hspi->Instance->CR1 & SPI_CR1_SPE) != SPI_CR1_SPE)
|
|
{
|
|
/* Enable SPI peripheral */
|
|
__HAL_SPI_ENABLE(hspi);
|
|
}
|
|
|
|
/* Process Unlocked */
|
|
__HAL_UNLOCK(hspi);
|
|
/* Enable RXNE and ERR interrupt */
|
|
__HAL_SPI_ENABLE_IT(hspi, (SPI_IT_RXNE | SPI_IT_ERR));
|
|
|
|
error :
|
|
return errorcode;
|
|
}
|
|
|
|
/**
|
|
* @brief Transmit and Receive an amount of data in non-blocking mode with Interrupt.
|
|
* @param hspi pointer to a SPI_HandleTypeDef structure that contains
|
|
* the configuration information for SPI module.
|
|
* @param pTxData pointer to transmission data buffer
|
|
* @param pRxData pointer to reception data buffer
|
|
* @param Size amount of data to be sent and received
|
|
* @retval HAL status
|
|
*/
|
|
HAL_StatusTypeDef HAL_SPI_TransmitReceive_IT(SPI_HandleTypeDef *hspi, uint8_t *pTxData, uint8_t *pRxData, uint16_t Size)
|
|
{
|
|
uint32_t tmp_mode;
|
|
HAL_SPI_StateTypeDef tmp_state;
|
|
HAL_StatusTypeDef errorcode = HAL_OK;
|
|
|
|
/* Check Direction parameter */
|
|
assert_param(IS_SPI_DIRECTION_2LINES(hspi->Init.Direction));
|
|
|
|
/* Init temporary variables */
|
|
tmp_state = hspi->State;
|
|
tmp_mode = hspi->Init.Mode;
|
|
|
|
if (!((tmp_state == HAL_SPI_STATE_READY) || \
|
|
((tmp_mode == SPI_MODE_MASTER) && (hspi->Init.Direction == SPI_DIRECTION_2LINES) && (tmp_state == HAL_SPI_STATE_BUSY_RX))))
|
|
{
|
|
errorcode = HAL_BUSY;
|
|
goto error;
|
|
}
|
|
|
|
if ((pTxData == NULL) || (pRxData == NULL) || (Size == 0U))
|
|
{
|
|
errorcode = HAL_ERROR;
|
|
goto error;
|
|
}
|
|
|
|
/* Process locked */
|
|
__HAL_LOCK(hspi);
|
|
|
|
/* Don't overwrite in case of HAL_SPI_STATE_BUSY_RX */
|
|
if (hspi->State != HAL_SPI_STATE_BUSY_RX)
|
|
{
|
|
hspi->State = HAL_SPI_STATE_BUSY_TX_RX;
|
|
}
|
|
|
|
/* Set the transaction information */
|
|
hspi->ErrorCode = HAL_SPI_ERROR_NONE;
|
|
hspi->pTxBuffPtr = (uint8_t *)pTxData;
|
|
hspi->TxXferSize = Size;
|
|
hspi->TxXferCount = Size;
|
|
hspi->pRxBuffPtr = (uint8_t *)pRxData;
|
|
hspi->RxXferSize = Size;
|
|
hspi->RxXferCount = Size;
|
|
|
|
/* Set the function for IT treatment */
|
|
if (hspi->Init.DataSize > SPI_DATASIZE_8BIT)
|
|
{
|
|
hspi->RxISR = SPI_2linesRxISR_16BIT;
|
|
hspi->TxISR = SPI_2linesTxISR_16BIT;
|
|
}
|
|
else
|
|
{
|
|
hspi->RxISR = SPI_2linesRxISR_8BIT;
|
|
hspi->TxISR = SPI_2linesTxISR_8BIT;
|
|
}
|
|
|
|
#if (USE_SPI_CRC != 0U)
|
|
/* Reset CRC Calculation */
|
|
if (hspi->Init.CRCCalculation == SPI_CRCCALCULATION_ENABLE)
|
|
{
|
|
hspi->CRCSize = 1U;
|
|
if ((hspi->Init.DataSize <= SPI_DATASIZE_8BIT) && (hspi->Init.CRCLength == SPI_CRC_LENGTH_16BIT))
|
|
{
|
|
hspi->CRCSize = 2U;
|
|
}
|
|
SPI_RESET_CRC(hspi);
|
|
}
|
|
else
|
|
{
|
|
hspi->CRCSize = 0U;
|
|
}
|
|
#endif /* USE_SPI_CRC */
|
|
|
|
/* Check if packing mode is enabled and if there is more than 2 data to receive */
|
|
if ((hspi->Init.DataSize > SPI_DATASIZE_8BIT) || (Size >= 2U))
|
|
{
|
|
/* Set RX Fifo threshold according the reception data length: 16 bit */
|
|
CLEAR_BIT(hspi->Instance->CR2, SPI_RXFIFO_THRESHOLD);
|
|
}
|
|
else
|
|
{
|
|
/* Set RX Fifo threshold according the reception data length: 8 bit */
|
|
SET_BIT(hspi->Instance->CR2, SPI_RXFIFO_THRESHOLD);
|
|
}
|
|
|
|
|
|
/* Check if the SPI is already enabled */
|
|
if ((hspi->Instance->CR1 & SPI_CR1_SPE) != SPI_CR1_SPE)
|
|
{
|
|
/* Enable SPI peripheral */
|
|
__HAL_SPI_ENABLE(hspi);
|
|
}
|
|
|
|
/* Process Unlocked */
|
|
__HAL_UNLOCK(hspi);
|
|
/* Enable TXE, RXNE and ERR interrupt */
|
|
__HAL_SPI_ENABLE_IT(hspi, (SPI_IT_TXE | SPI_IT_RXNE | SPI_IT_ERR));
|
|
|
|
error :
|
|
return errorcode;
|
|
}
|
|
|
|
/**
|
|
* @brief Transmit an amount of data in non-blocking mode with DMA.
|
|
* @param hspi pointer to a SPI_HandleTypeDef structure that contains
|
|
* the configuration information for SPI module.
|
|
* @param pData pointer to data buffer
|
|
* @param Size amount of data to be sent
|
|
* @retval HAL status
|
|
*/
|
|
HAL_StatusTypeDef HAL_SPI_Transmit_DMA(SPI_HandleTypeDef *hspi, uint8_t *pData, uint16_t Size)
|
|
{
|
|
HAL_StatusTypeDef errorcode = HAL_OK;
|
|
|
|
/* Check tx dma handle */
|
|
assert_param(IS_SPI_DMA_HANDLE(hspi->hdmatx));
|
|
|
|
/* Check Direction parameter */
|
|
assert_param(IS_SPI_DIRECTION_2LINES_OR_1LINE(hspi->Init.Direction));
|
|
|
|
/* Process Locked */
|
|
__HAL_LOCK(hspi);
|
|
|
|
if (hspi->State != HAL_SPI_STATE_READY)
|
|
{
|
|
errorcode = HAL_BUSY;
|
|
goto error;
|
|
}
|
|
|
|
if ((pData == NULL) || (Size == 0U))
|
|
{
|
|
errorcode = HAL_ERROR;
|
|
goto error;
|
|
}
|
|
|
|
/* Set the transaction information */
|
|
hspi->State = HAL_SPI_STATE_BUSY_TX;
|
|
hspi->ErrorCode = HAL_SPI_ERROR_NONE;
|
|
hspi->pTxBuffPtr = (uint8_t *)pData;
|
|
hspi->TxXferSize = Size;
|
|
hspi->TxXferCount = Size;
|
|
|
|
/* Init field not used in handle to zero */
|
|
hspi->pRxBuffPtr = (uint8_t *)NULL;
|
|
hspi->TxISR = NULL;
|
|
hspi->RxISR = NULL;
|
|
hspi->RxXferSize = 0U;
|
|
hspi->RxXferCount = 0U;
|
|
|
|
/* Configure communication direction : 1Line */
|
|
if (hspi->Init.Direction == SPI_DIRECTION_1LINE)
|
|
{
|
|
/* Disable SPI Peripheral before set 1Line direction (BIDIOE bit) */
|
|
__HAL_SPI_DISABLE(hspi);
|
|
SPI_1LINE_TX(hspi);
|
|
}
|
|
|
|
#if (USE_SPI_CRC != 0U)
|
|
/* Reset CRC Calculation */
|
|
if (hspi->Init.CRCCalculation == SPI_CRCCALCULATION_ENABLE)
|
|
{
|
|
SPI_RESET_CRC(hspi);
|
|
}
|
|
#endif /* USE_SPI_CRC */
|
|
|
|
/* Set the SPI TxDMA Half transfer complete callback */
|
|
hspi->hdmatx->XferHalfCpltCallback = SPI_DMAHalfTransmitCplt;
|
|
|
|
/* Set the SPI TxDMA transfer complete callback */
|
|
hspi->hdmatx->XferCpltCallback = SPI_DMATransmitCplt;
|
|
|
|
/* Set the DMA error callback */
|
|
hspi->hdmatx->XferErrorCallback = SPI_DMAError;
|
|
|
|
/* Set the DMA AbortCpltCallback */
|
|
hspi->hdmatx->XferAbortCallback = NULL;
|
|
|
|
CLEAR_BIT(hspi->Instance->CR2, SPI_CR2_LDMATX);
|
|
/* Packing mode is enabled only if the DMA setting is HALWORD */
|
|
if ((hspi->Init.DataSize <= SPI_DATASIZE_8BIT) && (hspi->hdmatx->Init.MemDataAlignment == DMA_MDATAALIGN_HALFWORD))
|
|
{
|
|
/* Check the even/odd of the data size + crc if enabled */
|
|
if ((hspi->TxXferCount & 0x1U) == 0U)
|
|
{
|
|
CLEAR_BIT(hspi->Instance->CR2, SPI_CR2_LDMATX);
|
|
hspi->TxXferCount = (hspi->TxXferCount >> 1U);
|
|
}
|
|
else
|
|
{
|
|
SET_BIT(hspi->Instance->CR2, SPI_CR2_LDMATX);
|
|
hspi->TxXferCount = (hspi->TxXferCount >> 1U) + 1U;
|
|
}
|
|
}
|
|
|
|
/* Enable the Tx DMA Stream/Channel */
|
|
if (HAL_OK != HAL_DMA_Start_IT(hspi->hdmatx, (uint32_t)hspi->pTxBuffPtr, (uint32_t)&hspi->Instance->DR,
|
|
hspi->TxXferCount))
|
|
{
|
|
/* Update SPI error code */
|
|
SET_BIT(hspi->ErrorCode, HAL_SPI_ERROR_DMA);
|
|
errorcode = HAL_ERROR;
|
|
|
|
goto error;
|
|
}
|
|
|
|
/* Check if the SPI is already enabled */
|
|
if ((hspi->Instance->CR1 & SPI_CR1_SPE) != SPI_CR1_SPE)
|
|
{
|
|
/* Enable SPI peripheral */
|
|
__HAL_SPI_ENABLE(hspi);
|
|
}
|
|
|
|
/* Enable the SPI Error Interrupt Bit */
|
|
__HAL_SPI_ENABLE_IT(hspi, (SPI_IT_ERR));
|
|
|
|
/* Enable Tx DMA Request */
|
|
SET_BIT(hspi->Instance->CR2, SPI_CR2_TXDMAEN);
|
|
|
|
error :
|
|
/* Process Unlocked */
|
|
__HAL_UNLOCK(hspi);
|
|
return errorcode;
|
|
}
|
|
|
|
/**
|
|
* @brief Receive an amount of data in non-blocking mode with DMA.
|
|
* @note In case of MASTER mode and SPI_DIRECTION_2LINES direction, hdmatx shall be defined.
|
|
* @param hspi pointer to a SPI_HandleTypeDef structure that contains
|
|
* the configuration information for SPI module.
|
|
* @param pData pointer to data buffer
|
|
* @note When the CRC feature is enabled the pData Length must be Size + 1.
|
|
* @param Size amount of data to be sent
|
|
* @retval HAL status
|
|
*/
|
|
HAL_StatusTypeDef HAL_SPI_Receive_DMA(SPI_HandleTypeDef *hspi, uint8_t *pData, uint16_t Size)
|
|
{
|
|
HAL_StatusTypeDef errorcode = HAL_OK;
|
|
|
|
/* Check rx dma handle */
|
|
assert_param(IS_SPI_DMA_HANDLE(hspi->hdmarx));
|
|
|
|
if (hspi->State != HAL_SPI_STATE_READY)
|
|
{
|
|
errorcode = HAL_BUSY;
|
|
goto error;
|
|
}
|
|
|
|
if ((hspi->Init.Direction == SPI_DIRECTION_2LINES) && (hspi->Init.Mode == SPI_MODE_MASTER))
|
|
{
|
|
hspi->State = HAL_SPI_STATE_BUSY_RX;
|
|
|
|
/* Check tx dma handle */
|
|
assert_param(IS_SPI_DMA_HANDLE(hspi->hdmatx));
|
|
|
|
/* Call transmit-receive function to send Dummy data on Tx line and generate clock on CLK line */
|
|
return HAL_SPI_TransmitReceive_DMA(hspi, pData, pData, Size);
|
|
}
|
|
|
|
/* Process Locked */
|
|
__HAL_LOCK(hspi);
|
|
|
|
if ((pData == NULL) || (Size == 0U))
|
|
{
|
|
errorcode = HAL_ERROR;
|
|
goto error;
|
|
}
|
|
|
|
/* Set the transaction information */
|
|
hspi->State = HAL_SPI_STATE_BUSY_RX;
|
|
hspi->ErrorCode = HAL_SPI_ERROR_NONE;
|
|
hspi->pRxBuffPtr = (uint8_t *)pData;
|
|
hspi->RxXferSize = Size;
|
|
hspi->RxXferCount = Size;
|
|
|
|
/*Init field not used in handle to zero */
|
|
hspi->RxISR = NULL;
|
|
hspi->TxISR = NULL;
|
|
hspi->TxXferSize = 0U;
|
|
hspi->TxXferCount = 0U;
|
|
|
|
/* Configure communication direction : 1Line */
|
|
if (hspi->Init.Direction == SPI_DIRECTION_1LINE)
|
|
{
|
|
/* Disable SPI Peripheral before set 1Line direction (BIDIOE bit) */
|
|
__HAL_SPI_DISABLE(hspi);
|
|
SPI_1LINE_RX(hspi);
|
|
}
|
|
|
|
#if (USE_SPI_CRC != 0U)
|
|
/* Reset CRC Calculation */
|
|
if (hspi->Init.CRCCalculation == SPI_CRCCALCULATION_ENABLE)
|
|
{
|
|
SPI_RESET_CRC(hspi);
|
|
}
|
|
#endif /* USE_SPI_CRC */
|
|
|
|
|
|
CLEAR_BIT(hspi->Instance->CR2, SPI_CR2_LDMARX);
|
|
if (hspi->Init.DataSize > SPI_DATASIZE_8BIT)
|
|
{
|
|
/* Set RX Fifo threshold according the reception data length: 16bit */
|
|
CLEAR_BIT(hspi->Instance->CR2, SPI_RXFIFO_THRESHOLD);
|
|
}
|
|
else
|
|
{
|
|
/* Set RX Fifo threshold according the reception data length: 8bit */
|
|
SET_BIT(hspi->Instance->CR2, SPI_RXFIFO_THRESHOLD);
|
|
|
|
if (hspi->hdmarx->Init.MemDataAlignment == DMA_MDATAALIGN_HALFWORD)
|
|
{
|
|
/* Set RX Fifo threshold according the reception data length: 16bit */
|
|
CLEAR_BIT(hspi->Instance->CR2, SPI_RXFIFO_THRESHOLD);
|
|
|
|
if ((hspi->RxXferCount & 0x1U) == 0x0U)
|
|
{
|
|
CLEAR_BIT(hspi->Instance->CR2, SPI_CR2_LDMARX);
|
|
hspi->RxXferCount = hspi->RxXferCount >> 1U;
|
|
}
|
|
else
|
|
{
|
|
SET_BIT(hspi->Instance->CR2, SPI_CR2_LDMARX);
|
|
hspi->RxXferCount = (hspi->RxXferCount >> 1U) + 1U;
|
|
}
|
|
}
|
|
}
|
|
|
|
/* Set the SPI RxDMA Half transfer complete callback */
|
|
hspi->hdmarx->XferHalfCpltCallback = SPI_DMAHalfReceiveCplt;
|
|
|
|
/* Set the SPI Rx DMA transfer complete callback */
|
|
hspi->hdmarx->XferCpltCallback = SPI_DMAReceiveCplt;
|
|
|
|
/* Set the DMA error callback */
|
|
hspi->hdmarx->XferErrorCallback = SPI_DMAError;
|
|
|
|
/* Set the DMA AbortCpltCallback */
|
|
hspi->hdmarx->XferAbortCallback = NULL;
|
|
|
|
/* Enable the Rx DMA Stream/Channel */
|
|
if (HAL_OK != HAL_DMA_Start_IT(hspi->hdmarx, (uint32_t)&hspi->Instance->DR, (uint32_t)hspi->pRxBuffPtr,
|
|
hspi->RxXferCount))
|
|
{
|
|
/* Update SPI error code */
|
|
SET_BIT(hspi->ErrorCode, HAL_SPI_ERROR_DMA);
|
|
errorcode = HAL_ERROR;
|
|
|
|
goto error;
|
|
}
|
|
|
|
/* Check if the SPI is already enabled */
|
|
if ((hspi->Instance->CR1 & SPI_CR1_SPE) != SPI_CR1_SPE)
|
|
{
|
|
/* Enable SPI peripheral */
|
|
__HAL_SPI_ENABLE(hspi);
|
|
}
|
|
|
|
/* Enable the SPI Error Interrupt Bit */
|
|
__HAL_SPI_ENABLE_IT(hspi, (SPI_IT_ERR));
|
|
|
|
/* Enable Rx DMA Request */
|
|
SET_BIT(hspi->Instance->CR2, SPI_CR2_RXDMAEN);
|
|
|
|
error:
|
|
/* Process Unlocked */
|
|
__HAL_UNLOCK(hspi);
|
|
return errorcode;
|
|
}
|
|
|
|
/**
|
|
* @brief Transmit and Receive an amount of data in non-blocking mode with DMA.
|
|
* @param hspi pointer to a SPI_HandleTypeDef structure that contains
|
|
* the configuration information for SPI module.
|
|
* @param pTxData pointer to transmission data buffer
|
|
* @param pRxData pointer to reception data buffer
|
|
* @note When the CRC feature is enabled the pRxData Length must be Size + 1
|
|
* @param Size amount of data to be sent
|
|
* @retval HAL status
|
|
*/
|
|
HAL_StatusTypeDef HAL_SPI_TransmitReceive_DMA(SPI_HandleTypeDef *hspi, uint8_t *pTxData, uint8_t *pRxData,
|
|
uint16_t Size)
|
|
{
|
|
uint32_t tmp_mode;
|
|
HAL_SPI_StateTypeDef tmp_state;
|
|
HAL_StatusTypeDef errorcode = HAL_OK;
|
|
|
|
/* Check rx & tx dma handles */
|
|
assert_param(IS_SPI_DMA_HANDLE(hspi->hdmarx));
|
|
assert_param(IS_SPI_DMA_HANDLE(hspi->hdmatx));
|
|
|
|
/* Check Direction parameter */
|
|
assert_param(IS_SPI_DIRECTION_2LINES(hspi->Init.Direction));
|
|
|
|
/* Process locked */
|
|
__HAL_LOCK(hspi);
|
|
|
|
/* Init temporary variables */
|
|
tmp_state = hspi->State;
|
|
tmp_mode = hspi->Init.Mode;
|
|
|
|
if (!((tmp_state == HAL_SPI_STATE_READY) ||
|
|
((tmp_mode == SPI_MODE_MASTER) && (hspi->Init.Direction == SPI_DIRECTION_2LINES) && (tmp_state == HAL_SPI_STATE_BUSY_RX))))
|
|
{
|
|
errorcode = HAL_BUSY;
|
|
goto error;
|
|
}
|
|
|
|
if ((pTxData == NULL) || (pRxData == NULL) || (Size == 0U))
|
|
{
|
|
errorcode = HAL_ERROR;
|
|
goto error;
|
|
}
|
|
|
|
/* Don't overwrite in case of HAL_SPI_STATE_BUSY_RX */
|
|
if (hspi->State != HAL_SPI_STATE_BUSY_RX)
|
|
{
|
|
hspi->State = HAL_SPI_STATE_BUSY_TX_RX;
|
|
}
|
|
|
|
/* Set the transaction information */
|
|
hspi->ErrorCode = HAL_SPI_ERROR_NONE;
|
|
hspi->pTxBuffPtr = (uint8_t *)pTxData;
|
|
hspi->TxXferSize = Size;
|
|
hspi->TxXferCount = Size;
|
|
hspi->pRxBuffPtr = (uint8_t *)pRxData;
|
|
hspi->RxXferSize = Size;
|
|
hspi->RxXferCount = Size;
|
|
|
|
/* Init field not used in handle to zero */
|
|
hspi->RxISR = NULL;
|
|
hspi->TxISR = NULL;
|
|
|
|
#if (USE_SPI_CRC != 0U)
|
|
/* Reset CRC Calculation */
|
|
if (hspi->Init.CRCCalculation == SPI_CRCCALCULATION_ENABLE)
|
|
{
|
|
SPI_RESET_CRC(hspi);
|
|
}
|
|
#endif /* USE_SPI_CRC */
|
|
|
|
/* Reset the threshold bit */
|
|
CLEAR_BIT(hspi->Instance->CR2, SPI_CR2_LDMATX | SPI_CR2_LDMARX);
|
|
|
|
/* The packing mode management is enabled by the DMA settings according the spi data size */
|
|
if (hspi->Init.DataSize > SPI_DATASIZE_8BIT)
|
|
{
|
|
/* Set fiforxthreshold according the reception data length: 16bit */
|
|
CLEAR_BIT(hspi->Instance->CR2, SPI_RXFIFO_THRESHOLD);
|
|
}
|
|
else
|
|
{
|
|
/* Set RX Fifo threshold according the reception data length: 8bit */
|
|
SET_BIT(hspi->Instance->CR2, SPI_RXFIFO_THRESHOLD);
|
|
|
|
if (hspi->hdmatx->Init.MemDataAlignment == DMA_MDATAALIGN_HALFWORD)
|
|
{
|
|
if ((hspi->TxXferSize & 0x1U) == 0x0U)
|
|
{
|
|
CLEAR_BIT(hspi->Instance->CR2, SPI_CR2_LDMATX);
|
|
hspi->TxXferCount = hspi->TxXferCount >> 1U;
|
|
}
|
|
else
|
|
{
|
|
SET_BIT(hspi->Instance->CR2, SPI_CR2_LDMATX);
|
|
hspi->TxXferCount = (hspi->TxXferCount >> 1U) + 1U;
|
|
}
|
|
}
|
|
|
|
if (hspi->hdmarx->Init.MemDataAlignment == DMA_MDATAALIGN_HALFWORD)
|
|
{
|
|
/* Set RX Fifo threshold according the reception data length: 16bit */
|
|
CLEAR_BIT(hspi->Instance->CR2, SPI_RXFIFO_THRESHOLD);
|
|
|
|
if ((hspi->RxXferCount & 0x1U) == 0x0U)
|
|
{
|
|
CLEAR_BIT(hspi->Instance->CR2, SPI_CR2_LDMARX);
|
|
hspi->RxXferCount = hspi->RxXferCount >> 1U;
|
|
}
|
|
else
|
|
{
|
|
SET_BIT(hspi->Instance->CR2, SPI_CR2_LDMARX);
|
|
hspi->RxXferCount = (hspi->RxXferCount >> 1U) + 1U;
|
|
}
|
|
}
|
|
}
|
|
|
|
/* Check if we are in Rx only or in Rx/Tx Mode and configure the DMA transfer complete callback */
|
|
if (hspi->State == HAL_SPI_STATE_BUSY_RX)
|
|
{
|
|
/* Set the SPI Rx DMA Half transfer complete callback */
|
|
hspi->hdmarx->XferHalfCpltCallback = SPI_DMAHalfReceiveCplt;
|
|
hspi->hdmarx->XferCpltCallback = SPI_DMAReceiveCplt;
|
|
}
|
|
else
|
|
{
|
|
/* Set the SPI Tx/Rx DMA Half transfer complete callback */
|
|
hspi->hdmarx->XferHalfCpltCallback = SPI_DMAHalfTransmitReceiveCplt;
|
|
hspi->hdmarx->XferCpltCallback = SPI_DMATransmitReceiveCplt;
|
|
}
|
|
|
|
/* Set the DMA error callback */
|
|
hspi->hdmarx->XferErrorCallback = SPI_DMAError;
|
|
|
|
/* Set the DMA AbortCpltCallback */
|
|
hspi->hdmarx->XferAbortCallback = NULL;
|
|
|
|
/* Enable the Rx DMA Stream/Channel */
|
|
if (HAL_OK != HAL_DMA_Start_IT(hspi->hdmarx, (uint32_t)&hspi->Instance->DR, (uint32_t)hspi->pRxBuffPtr,
|
|
hspi->RxXferCount))
|
|
{
|
|
/* Update SPI error code */
|
|
SET_BIT(hspi->ErrorCode, HAL_SPI_ERROR_DMA);
|
|
errorcode = HAL_ERROR;
|
|
|
|
goto error;
|
|
}
|
|
|
|
/* Enable Rx DMA Request */
|
|
SET_BIT(hspi->Instance->CR2, SPI_CR2_RXDMAEN);
|
|
|
|
/* Set the SPI Tx DMA transfer complete callback as NULL because the communication closing
|
|
is performed in DMA reception complete callback */
|
|
hspi->hdmatx->XferHalfCpltCallback = NULL;
|
|
hspi->hdmatx->XferCpltCallback = NULL;
|
|
hspi->hdmatx->XferErrorCallback = NULL;
|
|
hspi->hdmatx->XferAbortCallback = NULL;
|
|
|
|
/* Enable the Tx DMA Stream/Channel */
|
|
if (HAL_OK != HAL_DMA_Start_IT(hspi->hdmatx, (uint32_t)hspi->pTxBuffPtr, (uint32_t)&hspi->Instance->DR,
|
|
hspi->TxXferCount))
|
|
{
|
|
/* Update SPI error code */
|
|
SET_BIT(hspi->ErrorCode, HAL_SPI_ERROR_DMA);
|
|
errorcode = HAL_ERROR;
|
|
|
|
goto error;
|
|
}
|
|
|
|
/* Check if the SPI is already enabled */
|
|
if ((hspi->Instance->CR1 & SPI_CR1_SPE) != SPI_CR1_SPE)
|
|
{
|
|
/* Enable SPI peripheral */
|
|
__HAL_SPI_ENABLE(hspi);
|
|
}
|
|
/* Enable the SPI Error Interrupt Bit */
|
|
__HAL_SPI_ENABLE_IT(hspi, (SPI_IT_ERR));
|
|
|
|
/* Enable Tx DMA Request */
|
|
SET_BIT(hspi->Instance->CR2, SPI_CR2_TXDMAEN);
|
|
|
|
error :
|
|
/* Process Unlocked */
|
|
__HAL_UNLOCK(hspi);
|
|
return errorcode;
|
|
}
|
|
|
|
/**
|
|
* @brief Abort ongoing transfer (blocking mode).
|
|
* @param hspi SPI handle.
|
|
* @note This procedure could be used for aborting any ongoing transfer (Tx and Rx),
|
|
* started in Interrupt or DMA mode.
|
|
* This procedure performs following operations :
|
|
* - Disable SPI Interrupts (depending of transfer direction)
|
|
* - Disable the DMA transfer in the peripheral register (if enabled)
|
|
* - Abort DMA transfer by calling HAL_DMA_Abort (in case of transfer in DMA mode)
|
|
* - Set handle State to READY
|
|
* @note This procedure is executed in blocking mode : when exiting function, Abort is considered as completed.
|
|
* @retval HAL status
|
|
*/
|
|
HAL_StatusTypeDef HAL_SPI_Abort(SPI_HandleTypeDef *hspi)
|
|
{
|
|
HAL_StatusTypeDef errorcode;
|
|
__IO uint32_t count;
|
|
__IO uint32_t resetcount;
|
|
|
|
/* Initialized local variable */
|
|
errorcode = HAL_OK;
|
|
resetcount = SPI_DEFAULT_TIMEOUT * (SystemCoreClock / 24U / 1000U);
|
|
count = resetcount;
|
|
|
|
/* Clear ERRIE interrupt to avoid error interrupts generation during Abort procedure */
|
|
CLEAR_BIT(hspi->Instance->CR2, SPI_CR2_ERRIE);
|
|
|
|
/* Disable TXEIE, RXNEIE and ERRIE(mode fault event, overrun error, TI frame error) interrupts */
|
|
if (HAL_IS_BIT_SET(hspi->Instance->CR2, SPI_CR2_TXEIE))
|
|
{
|
|
hspi->TxISR = SPI_AbortTx_ISR;
|
|
/* Wait HAL_SPI_STATE_ABORT state */
|
|
do
|
|
{
|
|
if (count == 0U)
|
|
{
|
|
SET_BIT(hspi->ErrorCode, HAL_SPI_ERROR_ABORT);
|
|
break;
|
|
}
|
|
count--;
|
|
} while (hspi->State != HAL_SPI_STATE_ABORT);
|
|
/* Reset Timeout Counter */
|
|
count = resetcount;
|
|
}
|
|
|
|
if (HAL_IS_BIT_SET(hspi->Instance->CR2, SPI_CR2_RXNEIE))
|
|
{
|
|
hspi->RxISR = SPI_AbortRx_ISR;
|
|
/* Wait HAL_SPI_STATE_ABORT state */
|
|
do
|
|
{
|
|
if (count == 0U)
|
|
{
|
|
SET_BIT(hspi->ErrorCode, HAL_SPI_ERROR_ABORT);
|
|
break;
|
|
}
|
|
count--;
|
|
} while (hspi->State != HAL_SPI_STATE_ABORT);
|
|
/* Reset Timeout Counter */
|
|
count = resetcount;
|
|
}
|
|
|
|
/* Disable the SPI DMA Tx request if enabled */
|
|
if (HAL_IS_BIT_SET(hspi->Instance->CR2, SPI_CR2_TXDMAEN))
|
|
{
|
|
/* Abort the SPI DMA Tx Stream/Channel : use blocking DMA Abort API (no callback) */
|
|
if (hspi->hdmatx != NULL)
|
|
{
|
|
/* Set the SPI DMA Abort callback :
|
|
will lead to call HAL_SPI_AbortCpltCallback() at end of DMA abort procedure */
|
|
hspi->hdmatx->XferAbortCallback = NULL;
|
|
|
|
/* Abort DMA Tx Handle linked to SPI Peripheral */
|
|
if (HAL_DMA_Abort(hspi->hdmatx) != HAL_OK)
|
|
{
|
|
hspi->ErrorCode = HAL_SPI_ERROR_ABORT;
|
|
}
|
|
|
|
/* Disable Tx DMA Request */
|
|
CLEAR_BIT(hspi->Instance->CR2, (SPI_CR2_TXDMAEN));
|
|
|
|
if (SPI_EndRxTxTransaction(hspi, SPI_DEFAULT_TIMEOUT, HAL_GetTick()) != HAL_OK)
|
|
{
|
|
hspi->ErrorCode = HAL_SPI_ERROR_ABORT;
|
|
}
|
|
|
|
/* Disable SPI Peripheral */
|
|
__HAL_SPI_DISABLE(hspi);
|
|
|
|
/* Empty the FRLVL fifo */
|
|
if (SPI_WaitFifoStateUntilTimeout(hspi, SPI_FLAG_FRLVL, SPI_FRLVL_EMPTY, SPI_DEFAULT_TIMEOUT, HAL_GetTick()) != HAL_OK)
|
|
{
|
|
hspi->ErrorCode = HAL_SPI_ERROR_ABORT;
|
|
}
|
|
}
|
|
}
|
|
|
|
/* Disable the SPI DMA Rx request if enabled */
|
|
if (HAL_IS_BIT_SET(hspi->Instance->CR2, SPI_CR2_RXDMAEN))
|
|
{
|
|
/* Abort the SPI DMA Rx Stream/Channel : use blocking DMA Abort API (no callback) */
|
|
if (hspi->hdmarx != NULL)
|
|
{
|
|
/* Set the SPI DMA Abort callback :
|
|
will lead to call HAL_SPI_AbortCpltCallback() at end of DMA abort procedure */
|
|
hspi->hdmarx->XferAbortCallback = NULL;
|
|
|
|
/* Abort DMA Rx Handle linked to SPI Peripheral */
|
|
if (HAL_DMA_Abort(hspi->hdmarx) != HAL_OK)
|
|
{
|
|
hspi->ErrorCode = HAL_SPI_ERROR_ABORT;
|
|
}
|
|
|
|
/* Disable peripheral */
|
|
__HAL_SPI_DISABLE(hspi);
|
|
|
|
/* Control the BSY flag */
|
|
if (SPI_WaitFlagStateUntilTimeout(hspi, SPI_FLAG_BSY, RESET, SPI_DEFAULT_TIMEOUT, HAL_GetTick()) != HAL_OK)
|
|
{
|
|
hspi->ErrorCode = HAL_SPI_ERROR_ABORT;
|
|
}
|
|
|
|
/* Empty the FRLVL fifo */
|
|
if (SPI_WaitFifoStateUntilTimeout(hspi, SPI_FLAG_FRLVL, SPI_FRLVL_EMPTY, SPI_DEFAULT_TIMEOUT, HAL_GetTick()) != HAL_OK)
|
|
{
|
|
hspi->ErrorCode = HAL_SPI_ERROR_ABORT;
|
|
}
|
|
|
|
/* Disable Rx DMA Request */
|
|
CLEAR_BIT(hspi->Instance->CR2, (SPI_CR2_RXDMAEN));
|
|
}
|
|
}
|
|
/* Reset Tx and Rx transfer counters */
|
|
hspi->RxXferCount = 0U;
|
|
hspi->TxXferCount = 0U;
|
|
|
|
/* Check error during Abort procedure */
|
|
if (hspi->ErrorCode == HAL_SPI_ERROR_ABORT)
|
|
{
|
|
/* return HAL_Error in case of error during Abort procedure */
|
|
errorcode = HAL_ERROR;
|
|
}
|
|
else
|
|
{
|
|
/* Reset errorCode */
|
|
hspi->ErrorCode = HAL_SPI_ERROR_NONE;
|
|
}
|
|
|
|
/* Clear the Error flags in the SR register */
|
|
__HAL_SPI_CLEAR_OVRFLAG(hspi);
|
|
__HAL_SPI_CLEAR_FREFLAG(hspi);
|
|
|
|
/* Restore hspi->state to ready */
|
|
hspi->State = HAL_SPI_STATE_READY;
|
|
|
|
return errorcode;
|
|
}
|
|
|
|
/**
|
|
* @brief Abort ongoing transfer (Interrupt mode).
|
|
* @param hspi SPI handle.
|
|
* @note This procedure could be used for aborting any ongoing transfer (Tx and Rx),
|
|
* started in Interrupt or DMA mode.
|
|
* This procedure performs following operations :
|
|
* - Disable SPI Interrupts (depending of transfer direction)
|
|
* - Disable the DMA transfer in the peripheral register (if enabled)
|
|
* - Abort DMA transfer by calling HAL_DMA_Abort_IT (in case of transfer in DMA mode)
|
|
* - Set handle State to READY
|
|
* - At abort completion, call user abort complete callback
|
|
* @note This procedure is executed in Interrupt mode, meaning that abort procedure could be
|
|
* considered as completed only when user abort complete callback is executed (not when exiting function).
|
|
* @retval HAL status
|
|
*/
|
|
HAL_StatusTypeDef HAL_SPI_Abort_IT(SPI_HandleTypeDef *hspi)
|
|
{
|
|
HAL_StatusTypeDef errorcode;
|
|
uint32_t abortcplt ;
|
|
__IO uint32_t count;
|
|
__IO uint32_t resetcount;
|
|
|
|
/* Initialized local variable */
|
|
errorcode = HAL_OK;
|
|
abortcplt = 1U;
|
|
resetcount = SPI_DEFAULT_TIMEOUT * (SystemCoreClock / 24U / 1000U);
|
|
count = resetcount;
|
|
|
|
/* Clear ERRIE interrupt to avoid error interrupts generation during Abort procedure */
|
|
CLEAR_BIT(hspi->Instance->CR2, SPI_CR2_ERRIE);
|
|
|
|
/* Change Rx and Tx Irq Handler to Disable TXEIE, RXNEIE and ERRIE interrupts */
|
|
if (HAL_IS_BIT_SET(hspi->Instance->CR2, SPI_CR2_TXEIE))
|
|
{
|
|
hspi->TxISR = SPI_AbortTx_ISR;
|
|
/* Wait HAL_SPI_STATE_ABORT state */
|
|
do
|
|
{
|
|
if (count == 0U)
|
|
{
|
|
SET_BIT(hspi->ErrorCode, HAL_SPI_ERROR_ABORT);
|
|
break;
|
|
}
|
|
count--;
|
|
} while (hspi->State != HAL_SPI_STATE_ABORT);
|
|
/* Reset Timeout Counter */
|
|
count = resetcount;
|
|
}
|
|
|
|
if (HAL_IS_BIT_SET(hspi->Instance->CR2, SPI_CR2_RXNEIE))
|
|
{
|
|
hspi->RxISR = SPI_AbortRx_ISR;
|
|
/* Wait HAL_SPI_STATE_ABORT state */
|
|
do
|
|
{
|
|
if (count == 0U)
|
|
{
|
|
SET_BIT(hspi->ErrorCode, HAL_SPI_ERROR_ABORT);
|
|
break;
|
|
}
|
|
count--;
|
|
} while (hspi->State != HAL_SPI_STATE_ABORT);
|
|
/* Reset Timeout Counter */
|
|
count = resetcount;
|
|
}
|
|
|
|
/* If DMA Tx and/or DMA Rx Handles are associated to SPI Handle, DMA Abort complete callbacks should be initialised
|
|
before any call to DMA Abort functions */
|
|
/* DMA Tx Handle is valid */
|
|
if (hspi->hdmatx != NULL)
|
|
{
|
|
/* Set DMA Abort Complete callback if UART DMA Tx request if enabled.
|
|
Otherwise, set it to NULL */
|
|
if (HAL_IS_BIT_SET(hspi->Instance->CR2, SPI_CR2_TXDMAEN))
|
|
{
|
|
hspi->hdmatx->XferAbortCallback = SPI_DMATxAbortCallback;
|
|
}
|
|
else
|
|
{
|
|
hspi->hdmatx->XferAbortCallback = NULL;
|
|
}
|
|
}
|
|
/* DMA Rx Handle is valid */
|
|
if (hspi->hdmarx != NULL)
|
|
{
|
|
/* Set DMA Abort Complete callback if UART DMA Rx request if enabled.
|
|
Otherwise, set it to NULL */
|
|
if (HAL_IS_BIT_SET(hspi->Instance->CR2, SPI_CR2_RXDMAEN))
|
|
{
|
|
hspi->hdmarx->XferAbortCallback = SPI_DMARxAbortCallback;
|
|
}
|
|
else
|
|
{
|
|
hspi->hdmarx->XferAbortCallback = NULL;
|
|
}
|
|
}
|
|
|
|
/* Disable the SPI DMA Tx request if enabled */
|
|
if (HAL_IS_BIT_SET(hspi->Instance->CR2, SPI_CR2_TXDMAEN))
|
|
{
|
|
/* Abort the SPI DMA Tx Stream/Channel */
|
|
if (hspi->hdmatx != NULL)
|
|
{
|
|
/* Abort DMA Tx Handle linked to SPI Peripheral */
|
|
if (HAL_DMA_Abort_IT(hspi->hdmatx) != HAL_OK)
|
|
{
|
|
hspi->hdmatx->XferAbortCallback = NULL;
|
|
hspi->ErrorCode = HAL_SPI_ERROR_ABORT;
|
|
}
|
|
else
|
|
{
|
|
abortcplt = 0U;
|
|
}
|
|
}
|
|
}
|
|
/* Disable the SPI DMA Rx request if enabled */
|
|
if (HAL_IS_BIT_SET(hspi->Instance->CR2, SPI_CR2_RXDMAEN))
|
|
{
|
|
/* Abort the SPI DMA Rx Stream/Channel */
|
|
if (hspi->hdmarx != NULL)
|
|
{
|
|
/* Abort DMA Rx Handle linked to SPI Peripheral */
|
|
if (HAL_DMA_Abort_IT(hspi->hdmarx) != HAL_OK)
|
|
{
|
|
hspi->hdmarx->XferAbortCallback = NULL;
|
|
hspi->ErrorCode = HAL_SPI_ERROR_ABORT;
|
|
}
|
|
else
|
|
{
|
|
abortcplt = 0U;
|
|
}
|
|
}
|
|
}
|
|
|
|
if (abortcplt == 1U)
|
|
{
|
|
/* Reset Tx and Rx transfer counters */
|
|
hspi->RxXferCount = 0U;
|
|
hspi->TxXferCount = 0U;
|
|
|
|
/* Check error during Abort procedure */
|
|
if (hspi->ErrorCode == HAL_SPI_ERROR_ABORT)
|
|
{
|
|
/* return HAL_Error in case of error during Abort procedure */
|
|
errorcode = HAL_ERROR;
|
|
}
|
|
else
|
|
{
|
|
/* Reset errorCode */
|
|
hspi->ErrorCode = HAL_SPI_ERROR_NONE;
|
|
}
|
|
|
|
/* Clear the Error flags in the SR register */
|
|
__HAL_SPI_CLEAR_OVRFLAG(hspi);
|
|
__HAL_SPI_CLEAR_FREFLAG(hspi);
|
|
|
|
/* Restore hspi->State to Ready */
|
|
hspi->State = HAL_SPI_STATE_READY;
|
|
|
|
/* As no DMA to be aborted, call directly user Abort complete callback */
|
|
#if (USE_HAL_SPI_REGISTER_CALLBACKS == 1U)
|
|
hspi->AbortCpltCallback(hspi);
|
|
#else
|
|
HAL_SPI_AbortCpltCallback(hspi);
|
|
#endif /* USE_HAL_SPI_REGISTER_CALLBACKS */
|
|
}
|
|
|
|
return errorcode;
|
|
}
|
|
|
|
/**
|
|
* @brief Pause the DMA Transfer.
|
|
* @param hspi pointer to a SPI_HandleTypeDef structure that contains
|
|
* the configuration information for the specified SPI module.
|
|
* @retval HAL status
|
|
*/
|
|
HAL_StatusTypeDef HAL_SPI_DMAPause(SPI_HandleTypeDef *hspi)
|
|
{
|
|
/* Process Locked */
|
|
__HAL_LOCK(hspi);
|
|
|
|
/* Disable the SPI DMA Tx & Rx requests */
|
|
CLEAR_BIT(hspi->Instance->CR2, SPI_CR2_TXDMAEN | SPI_CR2_RXDMAEN);
|
|
|
|
/* Process Unlocked */
|
|
__HAL_UNLOCK(hspi);
|
|
|
|
return HAL_OK;
|
|
}
|
|
|
|
/**
|
|
* @brief Resume the DMA Transfer.
|
|
* @param hspi pointer to a SPI_HandleTypeDef structure that contains
|
|
* the configuration information for the specified SPI module.
|
|
* @retval HAL status
|
|
*/
|
|
HAL_StatusTypeDef HAL_SPI_DMAResume(SPI_HandleTypeDef *hspi)
|
|
{
|
|
/* Process Locked */
|
|
__HAL_LOCK(hspi);
|
|
|
|
/* Enable the SPI DMA Tx & Rx requests */
|
|
SET_BIT(hspi->Instance->CR2, SPI_CR2_TXDMAEN | SPI_CR2_RXDMAEN);
|
|
|
|
/* Process Unlocked */
|
|
__HAL_UNLOCK(hspi);
|
|
|
|
return HAL_OK;
|
|
}
|
|
|
|
/**
|
|
* @brief Stop the DMA Transfer.
|
|
* @param hspi pointer to a SPI_HandleTypeDef structure that contains
|
|
* the configuration information for the specified SPI module.
|
|
* @retval HAL status
|
|
*/
|
|
HAL_StatusTypeDef HAL_SPI_DMAStop(SPI_HandleTypeDef *hspi)
|
|
{
|
|
HAL_StatusTypeDef errorcode = HAL_OK;
|
|
/* The Lock is not implemented on this API to allow the user application
|
|
to call the HAL SPI API under callbacks HAL_SPI_TxCpltCallback() or HAL_SPI_RxCpltCallback() or HAL_SPI_TxRxCpltCallback():
|
|
when calling HAL_DMA_Abort() API the DMA TX/RX Transfer complete interrupt is generated
|
|
and the correspond call back is executed HAL_SPI_TxCpltCallback() or HAL_SPI_RxCpltCallback() or HAL_SPI_TxRxCpltCallback()
|
|
*/
|
|
|
|
/* Abort the SPI DMA tx Stream/Channel */
|
|
if (hspi->hdmatx != NULL)
|
|
{
|
|
if (HAL_OK != HAL_DMA_Abort(hspi->hdmatx))
|
|
{
|
|
SET_BIT(hspi->ErrorCode, HAL_SPI_ERROR_DMA);
|
|
errorcode = HAL_ERROR;
|
|
}
|
|
}
|
|
/* Abort the SPI DMA rx Stream/Channel */
|
|
if (hspi->hdmarx != NULL)
|
|
{
|
|
if (HAL_OK != HAL_DMA_Abort(hspi->hdmarx))
|
|
{
|
|
SET_BIT(hspi->ErrorCode, HAL_SPI_ERROR_DMA);
|
|
errorcode = HAL_ERROR;
|
|
}
|
|
}
|
|
|
|
/* Disable the SPI DMA Tx & Rx requests */
|
|
CLEAR_BIT(hspi->Instance->CR2, SPI_CR2_TXDMAEN | SPI_CR2_RXDMAEN);
|
|
hspi->State = HAL_SPI_STATE_READY;
|
|
return errorcode;
|
|
}
|
|
|
|
/**
|
|
* @brief Handle SPI interrupt request.
|
|
* @param hspi pointer to a SPI_HandleTypeDef structure that contains
|
|
* the configuration information for the specified SPI module.
|
|
* @retval None
|
|
*/
|
|
void HAL_SPI_IRQHandler(SPI_HandleTypeDef *hspi)
|
|
{
|
|
uint32_t itsource = hspi->Instance->CR2;
|
|
uint32_t itflag = hspi->Instance->SR;
|
|
|
|
/* SPI in mode Receiver ----------------------------------------------------*/
|
|
if ((SPI_CHECK_FLAG(itflag, SPI_FLAG_OVR) == RESET) &&
|
|
(SPI_CHECK_FLAG(itflag, SPI_FLAG_RXNE) != RESET) && (SPI_CHECK_IT_SOURCE(itsource, SPI_IT_RXNE) != RESET))
|
|
{
|
|
hspi->RxISR(hspi);
|
|
return;
|
|
}
|
|
|
|
/* SPI in mode Transmitter -------------------------------------------------*/
|
|
if ((SPI_CHECK_FLAG(itflag, SPI_FLAG_TXE) != RESET) && (SPI_CHECK_IT_SOURCE(itsource, SPI_IT_TXE) != RESET))
|
|
{
|
|
hspi->TxISR(hspi);
|
|
return;
|
|
}
|
|
|
|
/* SPI in Error Treatment --------------------------------------------------*/
|
|
if (((SPI_CHECK_FLAG(itflag, SPI_FLAG_MODF) != RESET) || (SPI_CHECK_FLAG(itflag, SPI_FLAG_OVR) != RESET)
|
|
|| (SPI_CHECK_FLAG(itflag, SPI_FLAG_FRE) != RESET)) && (SPI_CHECK_IT_SOURCE(itsource, SPI_IT_ERR) != RESET))
|
|
{
|
|
/* SPI Overrun error interrupt occurred ----------------------------------*/
|
|
if (SPI_CHECK_FLAG(itflag, SPI_FLAG_OVR) != RESET)
|
|
{
|
|
if (hspi->State != HAL_SPI_STATE_BUSY_TX)
|
|
{
|
|
SET_BIT(hspi->ErrorCode, HAL_SPI_ERROR_OVR);
|
|
__HAL_SPI_CLEAR_OVRFLAG(hspi);
|
|
}
|
|
else
|
|
{
|
|
__HAL_SPI_CLEAR_OVRFLAG(hspi);
|
|
return;
|
|
}
|
|
}
|
|
|
|
/* SPI Mode Fault error interrupt occurred -------------------------------*/
|
|
if (SPI_CHECK_FLAG(itflag, SPI_FLAG_MODF) != RESET)
|
|
{
|
|
SET_BIT(hspi->ErrorCode, HAL_SPI_ERROR_MODF);
|
|
__HAL_SPI_CLEAR_MODFFLAG(hspi);
|
|
}
|
|
|
|
/* SPI Frame error interrupt occurred ------------------------------------*/
|
|
if (SPI_CHECK_FLAG(itflag, SPI_FLAG_FRE) != RESET)
|
|
{
|
|
SET_BIT(hspi->ErrorCode, HAL_SPI_ERROR_FRE);
|
|
__HAL_SPI_CLEAR_FREFLAG(hspi);
|
|
}
|
|
|
|
if (hspi->ErrorCode != HAL_SPI_ERROR_NONE)
|
|
{
|
|
/* Disable all interrupts */
|
|
__HAL_SPI_DISABLE_IT(hspi, SPI_IT_RXNE | SPI_IT_TXE | SPI_IT_ERR);
|
|
|
|
hspi->State = HAL_SPI_STATE_READY;
|
|
/* Disable the SPI DMA requests if enabled */
|
|
if ((HAL_IS_BIT_SET(itsource, SPI_CR2_TXDMAEN)) || (HAL_IS_BIT_SET(itsource, SPI_CR2_RXDMAEN)))
|
|
{
|
|
CLEAR_BIT(hspi->Instance->CR2, (SPI_CR2_TXDMAEN | SPI_CR2_RXDMAEN));
|
|
|
|
/* Abort the SPI DMA Rx channel */
|
|
if (hspi->hdmarx != NULL)
|
|
{
|
|
/* Set the SPI DMA Abort callback :
|
|
will lead to call HAL_SPI_ErrorCallback() at end of DMA abort procedure */
|
|
hspi->hdmarx->XferAbortCallback = SPI_DMAAbortOnError;
|
|
if (HAL_OK != HAL_DMA_Abort_IT(hspi->hdmarx))
|
|
{
|
|
SET_BIT(hspi->ErrorCode, HAL_SPI_ERROR_ABORT);
|
|
}
|
|
}
|
|
/* Abort the SPI DMA Tx channel */
|
|
if (hspi->hdmatx != NULL)
|
|
{
|
|
/* Set the SPI DMA Abort callback :
|
|
will lead to call HAL_SPI_ErrorCallback() at end of DMA abort procedure */
|
|
hspi->hdmatx->XferAbortCallback = SPI_DMAAbortOnError;
|
|
if (HAL_OK != HAL_DMA_Abort_IT(hspi->hdmatx))
|
|
{
|
|
SET_BIT(hspi->ErrorCode, HAL_SPI_ERROR_ABORT);
|
|
}
|
|
}
|
|
}
|
|
else
|
|
{
|
|
/* Call user error callback */
|
|
#if (USE_HAL_SPI_REGISTER_CALLBACKS == 1U)
|
|
hspi->ErrorCallback(hspi);
|
|
#else
|
|
HAL_SPI_ErrorCallback(hspi);
|
|
#endif /* USE_HAL_SPI_REGISTER_CALLBACKS */
|
|
}
|
|
}
|
|
return;
|
|
}
|
|
}
|
|
|
|
/**
|
|
* @brief Tx Transfer completed callback.
|
|
* @param hspi pointer to a SPI_HandleTypeDef structure that contains
|
|
* the configuration information for SPI module.
|
|
* @retval None
|
|
*/
|
|
__weak void HAL_SPI_TxCpltCallback(SPI_HandleTypeDef *hspi)
|
|
{
|
|
/* Prevent unused argument(s) compilation warning */
|
|
UNUSED(hspi);
|
|
|
|
/* NOTE : This function should not be modified, when the callback is needed,
|
|
the HAL_SPI_TxCpltCallback should be implemented in the user file
|
|
*/
|
|
}
|
|
|
|
/**
|
|
* @brief Rx Transfer completed callback.
|
|
* @param hspi pointer to a SPI_HandleTypeDef structure that contains
|
|
* the configuration information for SPI module.
|
|
* @retval None
|
|
*/
|
|
__weak void HAL_SPI_RxCpltCallback(SPI_HandleTypeDef *hspi)
|
|
{
|
|
/* Prevent unused argument(s) compilation warning */
|
|
UNUSED(hspi);
|
|
|
|
/* NOTE : This function should not be modified, when the callback is needed,
|
|
the HAL_SPI_RxCpltCallback should be implemented in the user file
|
|
*/
|
|
}
|
|
|
|
/**
|
|
* @brief Tx and Rx Transfer completed callback.
|
|
* @param hspi pointer to a SPI_HandleTypeDef structure that contains
|
|
* the configuration information for SPI module.
|
|
* @retval None
|
|
*/
|
|
__weak void HAL_SPI_TxRxCpltCallback(SPI_HandleTypeDef *hspi)
|
|
{
|
|
/* Prevent unused argument(s) compilation warning */
|
|
UNUSED(hspi);
|
|
|
|
/* NOTE : This function should not be modified, when the callback is needed,
|
|
the HAL_SPI_TxRxCpltCallback should be implemented in the user file
|
|
*/
|
|
}
|
|
|
|
/**
|
|
* @brief Tx Half Transfer completed callback.
|
|
* @param hspi pointer to a SPI_HandleTypeDef structure that contains
|
|
* the configuration information for SPI module.
|
|
* @retval None
|
|
*/
|
|
__weak void HAL_SPI_TxHalfCpltCallback(SPI_HandleTypeDef *hspi)
|
|
{
|
|
/* Prevent unused argument(s) compilation warning */
|
|
UNUSED(hspi);
|
|
|
|
/* NOTE : This function should not be modified, when the callback is needed,
|
|
the HAL_SPI_TxHalfCpltCallback should be implemented in the user file
|
|
*/
|
|
}
|
|
|
|
/**
|
|
* @brief Rx Half Transfer completed callback.
|
|
* @param hspi pointer to a SPI_HandleTypeDef structure that contains
|
|
* the configuration information for SPI module.
|
|
* @retval None
|
|
*/
|
|
__weak void HAL_SPI_RxHalfCpltCallback(SPI_HandleTypeDef *hspi)
|
|
{
|
|
/* Prevent unused argument(s) compilation warning */
|
|
UNUSED(hspi);
|
|
|
|
/* NOTE : This function should not be modified, when the callback is needed,
|
|
the HAL_SPI_RxHalfCpltCallback() should be implemented in the user file
|
|
*/
|
|
}
|
|
|
|
/**
|
|
* @brief Tx and Rx Half Transfer callback.
|
|
* @param hspi pointer to a SPI_HandleTypeDef structure that contains
|
|
* the configuration information for SPI module.
|
|
* @retval None
|
|
*/
|
|
__weak void HAL_SPI_TxRxHalfCpltCallback(SPI_HandleTypeDef *hspi)
|
|
{
|
|
/* Prevent unused argument(s) compilation warning */
|
|
UNUSED(hspi);
|
|
|
|
/* NOTE : This function should not be modified, when the callback is needed,
|
|
the HAL_SPI_TxRxHalfCpltCallback() should be implemented in the user file
|
|
*/
|
|
}
|
|
|
|
/**
|
|
* @brief SPI error callback.
|
|
* @param hspi pointer to a SPI_HandleTypeDef structure that contains
|
|
* the configuration information for SPI module.
|
|
* @retval None
|
|
*/
|
|
__weak void HAL_SPI_ErrorCallback(SPI_HandleTypeDef *hspi)
|
|
{
|
|
/* Prevent unused argument(s) compilation warning */
|
|
UNUSED(hspi);
|
|
|
|
/* NOTE : This function should not be modified, when the callback is needed,
|
|
the HAL_SPI_ErrorCallback should be implemented in the user file
|
|
*/
|
|
/* NOTE : The ErrorCode parameter in the hspi handle is updated by the SPI processes
|
|
and user can use HAL_SPI_GetError() API to check the latest error occurred
|
|
*/
|
|
}
|
|
|
|
/**
|
|
* @brief SPI Abort Complete callback.
|
|
* @param hspi SPI handle.
|
|
* @retval None
|
|
*/
|
|
__weak void HAL_SPI_AbortCpltCallback(SPI_HandleTypeDef *hspi)
|
|
{
|
|
/* Prevent unused argument(s) compilation warning */
|
|
UNUSED(hspi);
|
|
|
|
/* NOTE : This function should not be modified, when the callback is needed,
|
|
the HAL_SPI_AbortCpltCallback can be implemented in the user file.
|
|
*/
|
|
}
|
|
|
|
/**
|
|
* @}
|
|
*/
|
|
|
|
/** @defgroup SPI_Exported_Functions_Group3 Peripheral State and Errors functions
|
|
* @brief SPI control functions
|
|
*
|
|
@verbatim
|
|
===============================================================================
|
|
##### Peripheral State and Errors functions #####
|
|
===============================================================================
|
|
[..]
|
|
This subsection provides a set of functions allowing to control the SPI.
|
|
(+) HAL_SPI_GetState() API can be helpful to check in run-time the state of the SPI peripheral
|
|
(+) HAL_SPI_GetError() check in run-time Errors occurring during communication
|
|
@endverbatim
|
|
* @{
|
|
*/
|
|
|
|
/**
|
|
* @brief Return the SPI handle state.
|
|
* @param hspi pointer to a SPI_HandleTypeDef structure that contains
|
|
* the configuration information for SPI module.
|
|
* @retval SPI state
|
|
*/
|
|
HAL_SPI_StateTypeDef HAL_SPI_GetState(SPI_HandleTypeDef *hspi)
|
|
{
|
|
/* Return SPI handle state */
|
|
return hspi->State;
|
|
}
|
|
|
|
/**
|
|
* @brief Return the SPI error code.
|
|
* @param hspi pointer to a SPI_HandleTypeDef structure that contains
|
|
* the configuration information for SPI module.
|
|
* @retval SPI error code in bitmap format
|
|
*/
|
|
uint32_t HAL_SPI_GetError(SPI_HandleTypeDef *hspi)
|
|
{
|
|
/* Return SPI ErrorCode */
|
|
return hspi->ErrorCode;
|
|
}
|
|
|
|
/**
|
|
* @}
|
|
*/
|
|
|
|
/**
|
|
* @}
|
|
*/
|
|
|
|
/** @addtogroup SPI_Private_Functions
|
|
* @brief Private functions
|
|
* @{
|
|
*/
|
|
|
|
/**
|
|
* @brief DMA SPI transmit process complete callback.
|
|
* @param hdma pointer to a DMA_HandleTypeDef structure that contains
|
|
* the configuration information for the specified DMA module.
|
|
* @retval None
|
|
*/
|
|
static void SPI_DMATransmitCplt(DMA_HandleTypeDef *hdma)
|
|
{
|
|
SPI_HandleTypeDef *hspi = (SPI_HandleTypeDef *)(((DMA_HandleTypeDef *)hdma)->Parent); /* Derogation MISRAC2012-Rule-11.5 */
|
|
uint32_t tickstart;
|
|
|
|
/* Init tickstart for timeout management*/
|
|
tickstart = HAL_GetTick();
|
|
|
|
/* DMA Normal Mode */
|
|
if ((hdma->Instance->CCR & DMA_CCR_CIRC) != DMA_CCR_CIRC)
|
|
{
|
|
/* Disable ERR interrupt */
|
|
__HAL_SPI_DISABLE_IT(hspi, SPI_IT_ERR);
|
|
|
|
/* Disable Tx DMA Request */
|
|
CLEAR_BIT(hspi->Instance->CR2, SPI_CR2_TXDMAEN);
|
|
|
|
/* Check the end of the transaction */
|
|
if (SPI_EndRxTxTransaction(hspi, SPI_DEFAULT_TIMEOUT, tickstart) != HAL_OK)
|
|
{
|
|
SET_BIT(hspi->ErrorCode, HAL_SPI_ERROR_FLAG);
|
|
}
|
|
|
|
/* Clear overrun flag in 2 Lines communication mode because received data is not read */
|
|
if (hspi->Init.Direction == SPI_DIRECTION_2LINES)
|
|
{
|
|
__HAL_SPI_CLEAR_OVRFLAG(hspi);
|
|
}
|
|
|
|
hspi->TxXferCount = 0U;
|
|
hspi->State = HAL_SPI_STATE_READY;
|
|
|
|
if (hspi->ErrorCode != HAL_SPI_ERROR_NONE)
|
|
{
|
|
/* Call user error callback */
|
|
#if (USE_HAL_SPI_REGISTER_CALLBACKS == 1U)
|
|
hspi->ErrorCallback(hspi);
|
|
#else
|
|
HAL_SPI_ErrorCallback(hspi);
|
|
#endif /* USE_HAL_SPI_REGISTER_CALLBACKS */
|
|
return;
|
|
}
|
|
}
|
|
/* Call user Tx complete callback */
|
|
#if (USE_HAL_SPI_REGISTER_CALLBACKS == 1U)
|
|
hspi->TxCpltCallback(hspi);
|
|
#else
|
|
HAL_SPI_TxCpltCallback(hspi);
|
|
#endif /* USE_HAL_SPI_REGISTER_CALLBACKS */
|
|
}
|
|
|
|
/**
|
|
* @brief DMA SPI receive process complete callback.
|
|
* @param hdma pointer to a DMA_HandleTypeDef structure that contains
|
|
* the configuration information for the specified DMA module.
|
|
* @retval None
|
|
*/
|
|
static void SPI_DMAReceiveCplt(DMA_HandleTypeDef *hdma)
|
|
{
|
|
SPI_HandleTypeDef *hspi = (SPI_HandleTypeDef *)(((DMA_HandleTypeDef *)hdma)->Parent); /* Derogation MISRAC2012-Rule-11.5 */
|
|
uint32_t tickstart;
|
|
#if (USE_SPI_CRC != 0U)
|
|
__IO uint32_t tmpreg = 0U;
|
|
__IO uint8_t *ptmpreg8;
|
|
__IO uint8_t tmpreg8 = 0;
|
|
#endif /* USE_SPI_CRC */
|
|
|
|
/* Init tickstart for timeout management*/
|
|
tickstart = HAL_GetTick();
|
|
|
|
/* DMA Normal Mode */
|
|
if ((hdma->Instance->CCR & DMA_CCR_CIRC) != DMA_CCR_CIRC)
|
|
{
|
|
/* Disable ERR interrupt */
|
|
__HAL_SPI_DISABLE_IT(hspi, SPI_IT_ERR);
|
|
|
|
#if (USE_SPI_CRC != 0U)
|
|
/* CRC handling */
|
|
if (hspi->Init.CRCCalculation == SPI_CRCCALCULATION_ENABLE)
|
|
{
|
|
/* Wait until RXNE flag */
|
|
if (SPI_WaitFlagStateUntilTimeout(hspi, SPI_FLAG_RXNE, SET, SPI_DEFAULT_TIMEOUT, tickstart) != HAL_OK)
|
|
{
|
|
/* Error on the CRC reception */
|
|
SET_BIT(hspi->ErrorCode, HAL_SPI_ERROR_CRC);
|
|
}
|
|
/* Read CRC */
|
|
if (hspi->Init.DataSize > SPI_DATASIZE_8BIT)
|
|
{
|
|
/* Read 16bit CRC */
|
|
tmpreg = READ_REG(hspi->Instance->DR);
|
|
/* To avoid GCC warning */
|
|
UNUSED(tmpreg);
|
|
}
|
|
else
|
|
{
|
|
/* Initialize the 8bit temporary pointer */
|
|
ptmpreg8 = (__IO uint8_t *)&hspi->Instance->DR;
|
|
/* Read 8bit CRC */
|
|
tmpreg8 = *ptmpreg8;
|
|
/* To avoid GCC warning */
|
|
UNUSED(tmpreg8);
|
|
|
|
if (hspi->Init.CRCLength == SPI_CRC_LENGTH_16BIT)
|
|
{
|
|
if (SPI_WaitFlagStateUntilTimeout(hspi, SPI_FLAG_RXNE, SET, SPI_DEFAULT_TIMEOUT, tickstart) != HAL_OK)
|
|
{
|
|
/* Error on the CRC reception */
|
|
SET_BIT(hspi->ErrorCode, HAL_SPI_ERROR_CRC);
|
|
}
|
|
/* Read 8bit CRC again in case of 16bit CRC in 8bit Data mode */
|
|
tmpreg8 = *ptmpreg8;
|
|
/* To avoid GCC warning */
|
|
UNUSED(tmpreg8);
|
|
}
|
|
}
|
|
}
|
|
#endif /* USE_SPI_CRC */
|
|
|
|
/* Check if we are in Master RX 2 line mode */
|
|
if ((hspi->Init.Direction == SPI_DIRECTION_2LINES) && (hspi->Init.Mode == SPI_MODE_MASTER))
|
|
{
|
|
/* Disable Rx/Tx DMA Request (done by default to handle the case master rx direction 2 lines) */
|
|
CLEAR_BIT(hspi->Instance->CR2, SPI_CR2_TXDMAEN | SPI_CR2_RXDMAEN);
|
|
}
|
|
else
|
|
{
|
|
/* Normal case */
|
|
CLEAR_BIT(hspi->Instance->CR2, SPI_CR2_RXDMAEN);
|
|
}
|
|
|
|
/* Check the end of the transaction */
|
|
if (SPI_EndRxTransaction(hspi, SPI_DEFAULT_TIMEOUT, tickstart) != HAL_OK)
|
|
{
|
|
hspi->ErrorCode = HAL_SPI_ERROR_FLAG;
|
|
}
|
|
|
|
hspi->RxXferCount = 0U;
|
|
hspi->State = HAL_SPI_STATE_READY;
|
|
|
|
#if (USE_SPI_CRC != 0U)
|
|
/* Check if CRC error occurred */
|
|
if (__HAL_SPI_GET_FLAG(hspi, SPI_FLAG_CRCERR))
|
|
{
|
|
SET_BIT(hspi->ErrorCode, HAL_SPI_ERROR_CRC);
|
|
__HAL_SPI_CLEAR_CRCERRFLAG(hspi);
|
|
}
|
|
#endif /* USE_SPI_CRC */
|
|
|
|
if (hspi->ErrorCode != HAL_SPI_ERROR_NONE)
|
|
{
|
|
/* Call user error callback */
|
|
#if (USE_HAL_SPI_REGISTER_CALLBACKS == 1U)
|
|
hspi->ErrorCallback(hspi);
|
|
#else
|
|
HAL_SPI_ErrorCallback(hspi);
|
|
#endif /* USE_HAL_SPI_REGISTER_CALLBACKS */
|
|
return;
|
|
}
|
|
}
|
|
/* Call user Rx complete callback */
|
|
#if (USE_HAL_SPI_REGISTER_CALLBACKS == 1U)
|
|
hspi->RxCpltCallback(hspi);
|
|
#else
|
|
HAL_SPI_RxCpltCallback(hspi);
|
|
#endif /* USE_HAL_SPI_REGISTER_CALLBACKS */
|
|
}
|
|
|
|
/**
|
|
* @brief DMA SPI transmit receive process complete callback.
|
|
* @param hdma pointer to a DMA_HandleTypeDef structure that contains
|
|
* the configuration information for the specified DMA module.
|
|
* @retval None
|
|
*/
|
|
static void SPI_DMATransmitReceiveCplt(DMA_HandleTypeDef *hdma)
|
|
{
|
|
SPI_HandleTypeDef *hspi = (SPI_HandleTypeDef *)(((DMA_HandleTypeDef *)hdma)->Parent); /* Derogation MISRAC2012-Rule-11.5 */
|
|
uint32_t tickstart;
|
|
#if (USE_SPI_CRC != 0U)
|
|
__IO uint32_t tmpreg = 0U;
|
|
__IO uint8_t *ptmpreg8;
|
|
__IO uint8_t tmpreg8 = 0;
|
|
#endif /* USE_SPI_CRC */
|
|
|
|
/* Init tickstart for timeout management*/
|
|
tickstart = HAL_GetTick();
|
|
|
|
/* DMA Normal Mode */
|
|
if ((hdma->Instance->CCR & DMA_CCR_CIRC) != DMA_CCR_CIRC)
|
|
{
|
|
/* Disable ERR interrupt */
|
|
__HAL_SPI_DISABLE_IT(hspi, SPI_IT_ERR);
|
|
|
|
#if (USE_SPI_CRC != 0U)
|
|
/* CRC handling */
|
|
if (hspi->Init.CRCCalculation == SPI_CRCCALCULATION_ENABLE)
|
|
{
|
|
if ((hspi->Init.DataSize == SPI_DATASIZE_8BIT) && (hspi->Init.CRCLength == SPI_CRC_LENGTH_8BIT))
|
|
{
|
|
if (SPI_WaitFifoStateUntilTimeout(hspi, SPI_FLAG_FRLVL, SPI_FRLVL_QUARTER_FULL, SPI_DEFAULT_TIMEOUT,
|
|
tickstart) != HAL_OK)
|
|
{
|
|
/* Error on the CRC reception */
|
|
SET_BIT(hspi->ErrorCode, HAL_SPI_ERROR_CRC);
|
|
}
|
|
/* Initialize the 8bit temporary pointer */
|
|
ptmpreg8 = (__IO uint8_t *)&hspi->Instance->DR;
|
|
/* Read 8bit CRC */
|
|
tmpreg8 = *ptmpreg8;
|
|
/* To avoid GCC warning */
|
|
UNUSED(tmpreg8);
|
|
}
|
|
else
|
|
{
|
|
if (SPI_WaitFifoStateUntilTimeout(hspi, SPI_FLAG_FRLVL, SPI_FRLVL_HALF_FULL, SPI_DEFAULT_TIMEOUT, tickstart) != HAL_OK)
|
|
{
|
|
/* Error on the CRC reception */
|
|
SET_BIT(hspi->ErrorCode, HAL_SPI_ERROR_CRC);
|
|
}
|
|
/* Read CRC to Flush DR and RXNE flag */
|
|
tmpreg = READ_REG(hspi->Instance->DR);
|
|
/* To avoid GCC warning */
|
|
UNUSED(tmpreg);
|
|
}
|
|
}
|
|
#endif /* USE_SPI_CRC */
|
|
|
|
/* Check the end of the transaction */
|
|
if (SPI_EndRxTxTransaction(hspi, SPI_DEFAULT_TIMEOUT, tickstart) != HAL_OK)
|
|
{
|
|
SET_BIT(hspi->ErrorCode, HAL_SPI_ERROR_FLAG);
|
|
}
|
|
|
|
/* Disable Rx/Tx DMA Request */
|
|
CLEAR_BIT(hspi->Instance->CR2, SPI_CR2_TXDMAEN | SPI_CR2_RXDMAEN);
|
|
|
|
hspi->TxXferCount = 0U;
|
|
hspi->RxXferCount = 0U;
|
|
hspi->State = HAL_SPI_STATE_READY;
|
|
|
|
#if (USE_SPI_CRC != 0U)
|
|
/* Check if CRC error occurred */
|
|
if (__HAL_SPI_GET_FLAG(hspi, SPI_FLAG_CRCERR))
|
|
{
|
|
SET_BIT(hspi->ErrorCode, HAL_SPI_ERROR_CRC);
|
|
__HAL_SPI_CLEAR_CRCERRFLAG(hspi);
|
|
}
|
|
#endif /* USE_SPI_CRC */
|
|
|
|
if (hspi->ErrorCode != HAL_SPI_ERROR_NONE)
|
|
{
|
|
/* Call user error callback */
|
|
#if (USE_HAL_SPI_REGISTER_CALLBACKS == 1U)
|
|
hspi->ErrorCallback(hspi);
|
|
#else
|
|
HAL_SPI_ErrorCallback(hspi);
|
|
#endif /* USE_HAL_SPI_REGISTER_CALLBACKS */
|
|
return;
|
|
}
|
|
}
|
|
/* Call user TxRx complete callback */
|
|
#if (USE_HAL_SPI_REGISTER_CALLBACKS == 1U)
|
|
hspi->TxRxCpltCallback(hspi);
|
|
#else
|
|
HAL_SPI_TxRxCpltCallback(hspi);
|
|
#endif /* USE_HAL_SPI_REGISTER_CALLBACKS */
|
|
}
|
|
|
|
/**
|
|
* @brief DMA SPI half transmit process complete callback.
|
|
* @param hdma pointer to a DMA_HandleTypeDef structure that contains
|
|
* the configuration information for the specified DMA module.
|
|
* @retval None
|
|
*/
|
|
static void SPI_DMAHalfTransmitCplt(DMA_HandleTypeDef *hdma)
|
|
{
|
|
SPI_HandleTypeDef *hspi = (SPI_HandleTypeDef *)(((DMA_HandleTypeDef *)hdma)->Parent); /* Derogation MISRAC2012-Rule-11.5 */
|
|
|
|
/* Call user Tx half complete callback */
|
|
#if (USE_HAL_SPI_REGISTER_CALLBACKS == 1U)
|
|
hspi->TxHalfCpltCallback(hspi);
|
|
#else
|
|
HAL_SPI_TxHalfCpltCallback(hspi);
|
|
#endif /* USE_HAL_SPI_REGISTER_CALLBACKS */
|
|
}
|
|
|
|
/**
|
|
* @brief DMA SPI half receive process complete callback
|
|
* @param hdma pointer to a DMA_HandleTypeDef structure that contains
|
|
* the configuration information for the specified DMA module.
|
|
* @retval None
|
|
*/
|
|
static void SPI_DMAHalfReceiveCplt(DMA_HandleTypeDef *hdma)
|
|
{
|
|
SPI_HandleTypeDef *hspi = (SPI_HandleTypeDef *)(((DMA_HandleTypeDef *)hdma)->Parent); /* Derogation MISRAC2012-Rule-11.5 */
|
|
|
|
/* Call user Rx half complete callback */
|
|
#if (USE_HAL_SPI_REGISTER_CALLBACKS == 1U)
|
|
hspi->RxHalfCpltCallback(hspi);
|
|
#else
|
|
HAL_SPI_RxHalfCpltCallback(hspi);
|
|
#endif /* USE_HAL_SPI_REGISTER_CALLBACKS */
|
|
}
|
|
|
|
/**
|
|
* @brief DMA SPI half transmit receive process complete callback.
|
|
* @param hdma pointer to a DMA_HandleTypeDef structure that contains
|
|
* the configuration information for the specified DMA module.
|
|
* @retval None
|
|
*/
|
|
static void SPI_DMAHalfTransmitReceiveCplt(DMA_HandleTypeDef *hdma)
|
|
{
|
|
SPI_HandleTypeDef *hspi = (SPI_HandleTypeDef *)(((DMA_HandleTypeDef *)hdma)->Parent); /* Derogation MISRAC2012-Rule-11.5 */
|
|
|
|
/* Call user TxRx half complete callback */
|
|
#if (USE_HAL_SPI_REGISTER_CALLBACKS == 1U)
|
|
hspi->TxRxHalfCpltCallback(hspi);
|
|
#else
|
|
HAL_SPI_TxRxHalfCpltCallback(hspi);
|
|
#endif /* USE_HAL_SPI_REGISTER_CALLBACKS */
|
|
}
|
|
|
|
/**
|
|
* @brief DMA SPI communication error callback.
|
|
* @param hdma pointer to a DMA_HandleTypeDef structure that contains
|
|
* the configuration information for the specified DMA module.
|
|
* @retval None
|
|
*/
|
|
static void SPI_DMAError(DMA_HandleTypeDef *hdma)
|
|
{
|
|
SPI_HandleTypeDef *hspi = (SPI_HandleTypeDef *)(((DMA_HandleTypeDef *)hdma)->Parent); /* Derogation MISRAC2012-Rule-11.5 */
|
|
|
|
/* Stop the disable DMA transfer on SPI side */
|
|
CLEAR_BIT(hspi->Instance->CR2, SPI_CR2_TXDMAEN | SPI_CR2_RXDMAEN);
|
|
|
|
SET_BIT(hspi->ErrorCode, HAL_SPI_ERROR_DMA);
|
|
hspi->State = HAL_SPI_STATE_READY;
|
|
/* Call user error callback */
|
|
#if (USE_HAL_SPI_REGISTER_CALLBACKS == 1U)
|
|
hspi->ErrorCallback(hspi);
|
|
#else
|
|
HAL_SPI_ErrorCallback(hspi);
|
|
#endif /* USE_HAL_SPI_REGISTER_CALLBACKS */
|
|
}
|
|
|
|
/**
|
|
* @brief DMA SPI communication abort callback, when initiated by HAL services on Error
|
|
* (To be called at end of DMA Abort procedure following error occurrence).
|
|
* @param hdma DMA handle.
|
|
* @retval None
|
|
*/
|
|
static void SPI_DMAAbortOnError(DMA_HandleTypeDef *hdma)
|
|
{
|
|
SPI_HandleTypeDef *hspi = (SPI_HandleTypeDef *)(((DMA_HandleTypeDef *)hdma)->Parent); /* Derogation MISRAC2012-Rule-11.5 */
|
|
hspi->RxXferCount = 0U;
|
|
hspi->TxXferCount = 0U;
|
|
|
|
/* Call user error callback */
|
|
#if (USE_HAL_SPI_REGISTER_CALLBACKS == 1U)
|
|
hspi->ErrorCallback(hspi);
|
|
#else
|
|
HAL_SPI_ErrorCallback(hspi);
|
|
#endif /* USE_HAL_SPI_REGISTER_CALLBACKS */
|
|
}
|
|
|
|
/**
|
|
* @brief DMA SPI Tx communication abort callback, when initiated by user
|
|
* (To be called at end of DMA Tx Abort procedure following user abort request).
|
|
* @note When this callback is executed, User Abort complete call back is called only if no
|
|
* Abort still ongoing for Rx DMA Handle.
|
|
* @param hdma DMA handle.
|
|
* @retval None
|
|
*/
|
|
static void SPI_DMATxAbortCallback(DMA_HandleTypeDef *hdma)
|
|
{
|
|
SPI_HandleTypeDef *hspi = (SPI_HandleTypeDef *)(((DMA_HandleTypeDef *)hdma)->Parent); /* Derogation MISRAC2012-Rule-11.5 */
|
|
|
|
hspi->hdmatx->XferAbortCallback = NULL;
|
|
|
|
/* Disable Tx DMA Request */
|
|
CLEAR_BIT(hspi->Instance->CR2, SPI_CR2_TXDMAEN);
|
|
|
|
if (SPI_EndRxTxTransaction(hspi, SPI_DEFAULT_TIMEOUT, HAL_GetTick()) != HAL_OK)
|
|
{
|
|
hspi->ErrorCode = HAL_SPI_ERROR_ABORT;
|
|
}
|
|
|
|
/* Disable SPI Peripheral */
|
|
__HAL_SPI_DISABLE(hspi);
|
|
|
|
/* Empty the FRLVL fifo */
|
|
if (SPI_WaitFifoStateUntilTimeout(hspi, SPI_FLAG_FRLVL, SPI_FRLVL_EMPTY, SPI_DEFAULT_TIMEOUT, HAL_GetTick()) != HAL_OK)
|
|
{
|
|
hspi->ErrorCode = HAL_SPI_ERROR_ABORT;
|
|
}
|
|
|
|
/* Check if an Abort process is still ongoing */
|
|
if (hspi->hdmarx != NULL)
|
|
{
|
|
if (hspi->hdmarx->XferAbortCallback != NULL)
|
|
{
|
|
return;
|
|
}
|
|
}
|
|
|
|
/* No Abort process still ongoing : All DMA Stream/Channel are aborted, call user Abort Complete callback */
|
|
hspi->RxXferCount = 0U;
|
|
hspi->TxXferCount = 0U;
|
|
|
|
/* Check no error during Abort procedure */
|
|
if (hspi->ErrorCode != HAL_SPI_ERROR_ABORT)
|
|
{
|
|
/* Reset errorCode */
|
|
hspi->ErrorCode = HAL_SPI_ERROR_NONE;
|
|
}
|
|
|
|
/* Clear the Error flags in the SR register */
|
|
__HAL_SPI_CLEAR_OVRFLAG(hspi);
|
|
__HAL_SPI_CLEAR_FREFLAG(hspi);
|
|
|
|
/* Restore hspi->State to Ready */
|
|
hspi->State = HAL_SPI_STATE_READY;
|
|
|
|
/* Call user Abort complete callback */
|
|
#if (USE_HAL_SPI_REGISTER_CALLBACKS == 1U)
|
|
hspi->AbortCpltCallback(hspi);
|
|
#else
|
|
HAL_SPI_AbortCpltCallback(hspi);
|
|
#endif /* USE_HAL_SPI_REGISTER_CALLBACKS */
|
|
}
|
|
|
|
/**
|
|
* @brief DMA SPI Rx communication abort callback, when initiated by user
|
|
* (To be called at end of DMA Rx Abort procedure following user abort request).
|
|
* @note When this callback is executed, User Abort complete call back is called only if no
|
|
* Abort still ongoing for Tx DMA Handle.
|
|
* @param hdma DMA handle.
|
|
* @retval None
|
|
*/
|
|
static void SPI_DMARxAbortCallback(DMA_HandleTypeDef *hdma)
|
|
{
|
|
SPI_HandleTypeDef *hspi = (SPI_HandleTypeDef *)(((DMA_HandleTypeDef *)hdma)->Parent); /* Derogation MISRAC2012-Rule-11.5 */
|
|
|
|
/* Disable SPI Peripheral */
|
|
__HAL_SPI_DISABLE(hspi);
|
|
|
|
hspi->hdmarx->XferAbortCallback = NULL;
|
|
|
|
/* Disable Rx DMA Request */
|
|
CLEAR_BIT(hspi->Instance->CR2, SPI_CR2_RXDMAEN);
|
|
|
|
/* Control the BSY flag */
|
|
if (SPI_WaitFlagStateUntilTimeout(hspi, SPI_FLAG_BSY, RESET, SPI_DEFAULT_TIMEOUT, HAL_GetTick()) != HAL_OK)
|
|
{
|
|
hspi->ErrorCode = HAL_SPI_ERROR_ABORT;
|
|
}
|
|
|
|
/* Empty the FRLVL fifo */
|
|
if (SPI_WaitFifoStateUntilTimeout(hspi, SPI_FLAG_FRLVL, SPI_FRLVL_EMPTY, SPI_DEFAULT_TIMEOUT, HAL_GetTick()) != HAL_OK)
|
|
{
|
|
hspi->ErrorCode = HAL_SPI_ERROR_ABORT;
|
|
}
|
|
|
|
/* Check if an Abort process is still ongoing */
|
|
if (hspi->hdmatx != NULL)
|
|
{
|
|
if (hspi->hdmatx->XferAbortCallback != NULL)
|
|
{
|
|
return;
|
|
}
|
|
}
|
|
|
|
/* No Abort process still ongoing : All DMA Stream/Channel are aborted, call user Abort Complete callback */
|
|
hspi->RxXferCount = 0U;
|
|
hspi->TxXferCount = 0U;
|
|
|
|
/* Check no error during Abort procedure */
|
|
if (hspi->ErrorCode != HAL_SPI_ERROR_ABORT)
|
|
{
|
|
/* Reset errorCode */
|
|
hspi->ErrorCode = HAL_SPI_ERROR_NONE;
|
|
}
|
|
|
|
/* Clear the Error flags in the SR register */
|
|
__HAL_SPI_CLEAR_OVRFLAG(hspi);
|
|
__HAL_SPI_CLEAR_FREFLAG(hspi);
|
|
|
|
/* Restore hspi->State to Ready */
|
|
hspi->State = HAL_SPI_STATE_READY;
|
|
|
|
/* Call user Abort complete callback */
|
|
#if (USE_HAL_SPI_REGISTER_CALLBACKS == 1U)
|
|
hspi->AbortCpltCallback(hspi);
|
|
#else
|
|
HAL_SPI_AbortCpltCallback(hspi);
|
|
#endif /* USE_HAL_SPI_REGISTER_CALLBACKS */
|
|
}
|
|
|
|
/**
|
|
* @brief Rx 8-bit handler for Transmit and Receive in Interrupt mode.
|
|
* @param hspi pointer to a SPI_HandleTypeDef structure that contains
|
|
* the configuration information for SPI module.
|
|
* @retval None
|
|
*/
|
|
static void SPI_2linesRxISR_8BIT(struct __SPI_HandleTypeDef *hspi)
|
|
{
|
|
/* Receive data in packing mode */
|
|
if (hspi->RxXferCount > 1U)
|
|
{
|
|
*((uint16_t *)hspi->pRxBuffPtr) = (uint16_t)(hspi->Instance->DR);
|
|
hspi->pRxBuffPtr += sizeof(uint16_t);
|
|
hspi->RxXferCount -= 2U;
|
|
if (hspi->RxXferCount == 1U)
|
|
{
|
|
/* Set RX Fifo threshold according the reception data length: 8bit */
|
|
SET_BIT(hspi->Instance->CR2, SPI_RXFIFO_THRESHOLD);
|
|
}
|
|
}
|
|
/* Receive data in 8 Bit mode */
|
|
else
|
|
{
|
|
*hspi->pRxBuffPtr = *((__IO uint8_t *)&hspi->Instance->DR);
|
|
hspi->pRxBuffPtr++;
|
|
hspi->RxXferCount--;
|
|
}
|
|
|
|
/* Check end of the reception */
|
|
if (hspi->RxXferCount == 0U)
|
|
{
|
|
#if (USE_SPI_CRC != 0U)
|
|
if (hspi->Init.CRCCalculation == SPI_CRCCALCULATION_ENABLE)
|
|
{
|
|
SET_BIT(hspi->Instance->CR2, SPI_RXFIFO_THRESHOLD);
|
|
hspi->RxISR = SPI_2linesRxISR_8BITCRC;
|
|
return;
|
|
}
|
|
#endif /* USE_SPI_CRC */
|
|
|
|
/* Disable RXNE and ERR interrupt */
|
|
__HAL_SPI_DISABLE_IT(hspi, (SPI_IT_RXNE | SPI_IT_ERR));
|
|
|
|
if (hspi->TxXferCount == 0U)
|
|
{
|
|
SPI_CloseRxTx_ISR(hspi);
|
|
}
|
|
}
|
|
}
|
|
|
|
#if (USE_SPI_CRC != 0U)
|
|
/**
|
|
* @brief Rx 8-bit handler for Transmit and Receive in Interrupt mode.
|
|
* @param hspi pointer to a SPI_HandleTypeDef structure that contains
|
|
* the configuration information for SPI module.
|
|
* @retval None
|
|
*/
|
|
static void SPI_2linesRxISR_8BITCRC(struct __SPI_HandleTypeDef *hspi)
|
|
{
|
|
__IO uint8_t *ptmpreg8;
|
|
__IO uint8_t tmpreg8 = 0;
|
|
|
|
/* Initialize the 8bit temporary pointer */
|
|
ptmpreg8 = (__IO uint8_t *)&hspi->Instance->DR;
|
|
/* Read 8bit CRC to flush Data Register */
|
|
tmpreg8 = *ptmpreg8;
|
|
/* To avoid GCC warning */
|
|
UNUSED(tmpreg8);
|
|
|
|
hspi->CRCSize--;
|
|
|
|
/* Check end of the reception */
|
|
if (hspi->CRCSize == 0U)
|
|
{
|
|
/* Disable RXNE and ERR interrupt */
|
|
__HAL_SPI_DISABLE_IT(hspi, (SPI_IT_RXNE | SPI_IT_ERR));
|
|
|
|
if (hspi->TxXferCount == 0U)
|
|
{
|
|
SPI_CloseRxTx_ISR(hspi);
|
|
}
|
|
}
|
|
}
|
|
#endif /* USE_SPI_CRC */
|
|
|
|
/**
|
|
* @brief Tx 8-bit handler for Transmit and Receive in Interrupt mode.
|
|
* @param hspi pointer to a SPI_HandleTypeDef structure that contains
|
|
* the configuration information for SPI module.
|
|
* @retval None
|
|
*/
|
|
static void SPI_2linesTxISR_8BIT(struct __SPI_HandleTypeDef *hspi)
|
|
{
|
|
/* Transmit data in packing Bit mode */
|
|
if (hspi->TxXferCount >= 2U)
|
|
{
|
|
hspi->Instance->DR = *((uint16_t *)hspi->pTxBuffPtr);
|
|
hspi->pTxBuffPtr += sizeof(uint16_t);
|
|
hspi->TxXferCount -= 2U;
|
|
}
|
|
/* Transmit data in 8 Bit mode */
|
|
else
|
|
{
|
|
*(__IO uint8_t *)&hspi->Instance->DR = (*hspi->pTxBuffPtr);
|
|
hspi->pTxBuffPtr++;
|
|
hspi->TxXferCount--;
|
|
}
|
|
|
|
/* Check the end of the transmission */
|
|
if (hspi->TxXferCount == 0U)
|
|
{
|
|
#if (USE_SPI_CRC != 0U)
|
|
if (hspi->Init.CRCCalculation == SPI_CRCCALCULATION_ENABLE)
|
|
{
|
|
/* Set CRC Next Bit to send CRC */
|
|
SET_BIT(hspi->Instance->CR1, SPI_CR1_CRCNEXT);
|
|
/* Disable TXE interrupt */
|
|
__HAL_SPI_DISABLE_IT(hspi, SPI_IT_TXE);
|
|
return;
|
|
}
|
|
#endif /* USE_SPI_CRC */
|
|
|
|
/* Disable TXE interrupt */
|
|
__HAL_SPI_DISABLE_IT(hspi, SPI_IT_TXE);
|
|
|
|
if (hspi->RxXferCount == 0U)
|
|
{
|
|
SPI_CloseRxTx_ISR(hspi);
|
|
}
|
|
}
|
|
}
|
|
|
|
/**
|
|
* @brief Rx 16-bit handler for Transmit and Receive in Interrupt mode.
|
|
* @param hspi pointer to a SPI_HandleTypeDef structure that contains
|
|
* the configuration information for SPI module.
|
|
* @retval None
|
|
*/
|
|
static void SPI_2linesRxISR_16BIT(struct __SPI_HandleTypeDef *hspi)
|
|
{
|
|
/* Receive data in 16 Bit mode */
|
|
*((uint16_t *)hspi->pRxBuffPtr) = (uint16_t)(hspi->Instance->DR);
|
|
hspi->pRxBuffPtr += sizeof(uint16_t);
|
|
hspi->RxXferCount--;
|
|
|
|
if (hspi->RxXferCount == 0U)
|
|
{
|
|
#if (USE_SPI_CRC != 0U)
|
|
if (hspi->Init.CRCCalculation == SPI_CRCCALCULATION_ENABLE)
|
|
{
|
|
hspi->RxISR = SPI_2linesRxISR_16BITCRC;
|
|
return;
|
|
}
|
|
#endif /* USE_SPI_CRC */
|
|
|
|
/* Disable RXNE interrupt */
|
|
__HAL_SPI_DISABLE_IT(hspi, SPI_IT_RXNE);
|
|
|
|
if (hspi->TxXferCount == 0U)
|
|
{
|
|
SPI_CloseRxTx_ISR(hspi);
|
|
}
|
|
}
|
|
}
|
|
|
|
#if (USE_SPI_CRC != 0U)
|
|
/**
|
|
* @brief Manage the CRC 16-bit receive for Transmit and Receive in Interrupt mode.
|
|
* @param hspi pointer to a SPI_HandleTypeDef structure that contains
|
|
* the configuration information for SPI module.
|
|
* @retval None
|
|
*/
|
|
static void SPI_2linesRxISR_16BITCRC(struct __SPI_HandleTypeDef *hspi)
|
|
{
|
|
__IO uint32_t tmpreg = 0U;
|
|
|
|
/* Read 16bit CRC to flush Data Register */
|
|
tmpreg = READ_REG(hspi->Instance->DR);
|
|
/* To avoid GCC warning */
|
|
UNUSED(tmpreg);
|
|
|
|
/* Disable RXNE interrupt */
|
|
__HAL_SPI_DISABLE_IT(hspi, SPI_IT_RXNE);
|
|
|
|
SPI_CloseRxTx_ISR(hspi);
|
|
}
|
|
#endif /* USE_SPI_CRC */
|
|
|
|
/**
|
|
* @brief Tx 16-bit handler for Transmit and Receive in Interrupt mode.
|
|
* @param hspi pointer to a SPI_HandleTypeDef structure that contains
|
|
* the configuration information for SPI module.
|
|
* @retval None
|
|
*/
|
|
static void SPI_2linesTxISR_16BIT(struct __SPI_HandleTypeDef *hspi)
|
|
{
|
|
/* Transmit data in 16 Bit mode */
|
|
hspi->Instance->DR = *((uint16_t *)hspi->pTxBuffPtr);
|
|
hspi->pTxBuffPtr += sizeof(uint16_t);
|
|
hspi->TxXferCount--;
|
|
|
|
/* Enable CRC Transmission */
|
|
if (hspi->TxXferCount == 0U)
|
|
{
|
|
#if (USE_SPI_CRC != 0U)
|
|
if (hspi->Init.CRCCalculation == SPI_CRCCALCULATION_ENABLE)
|
|
{
|
|
/* Set CRC Next Bit to send CRC */
|
|
SET_BIT(hspi->Instance->CR1, SPI_CR1_CRCNEXT);
|
|
/* Disable TXE interrupt */
|
|
__HAL_SPI_DISABLE_IT(hspi, SPI_IT_TXE);
|
|
return;
|
|
}
|
|
#endif /* USE_SPI_CRC */
|
|
|
|
/* Disable TXE interrupt */
|
|
__HAL_SPI_DISABLE_IT(hspi, SPI_IT_TXE);
|
|
|
|
if (hspi->RxXferCount == 0U)
|
|
{
|
|
SPI_CloseRxTx_ISR(hspi);
|
|
}
|
|
}
|
|
}
|
|
|
|
#if (USE_SPI_CRC != 0U)
|
|
/**
|
|
* @brief Manage the CRC 8-bit receive in Interrupt context.
|
|
* @param hspi pointer to a SPI_HandleTypeDef structure that contains
|
|
* the configuration information for SPI module.
|
|
* @retval None
|
|
*/
|
|
static void SPI_RxISR_8BITCRC(struct __SPI_HandleTypeDef *hspi)
|
|
{
|
|
__IO uint8_t *ptmpreg8;
|
|
__IO uint8_t tmpreg8 = 0;
|
|
|
|
/* Initialize the 8bit temporary pointer */
|
|
ptmpreg8 = (__IO uint8_t *)&hspi->Instance->DR;
|
|
/* Read 8bit CRC to flush Data Register */
|
|
tmpreg8 = *ptmpreg8;
|
|
/* To avoid GCC warning */
|
|
UNUSED(tmpreg8);
|
|
|
|
hspi->CRCSize--;
|
|
|
|
if (hspi->CRCSize == 0U)
|
|
{
|
|
SPI_CloseRx_ISR(hspi);
|
|
}
|
|
}
|
|
#endif /* USE_SPI_CRC */
|
|
|
|
/**
|
|
* @brief Manage the receive 8-bit in Interrupt context.
|
|
* @param hspi pointer to a SPI_HandleTypeDef structure that contains
|
|
* the configuration information for SPI module.
|
|
* @retval None
|
|
*/
|
|
static void SPI_RxISR_8BIT(struct __SPI_HandleTypeDef *hspi)
|
|
{
|
|
*hspi->pRxBuffPtr = (*(__IO uint8_t *)&hspi->Instance->DR);
|
|
hspi->pRxBuffPtr++;
|
|
hspi->RxXferCount--;
|
|
|
|
#if (USE_SPI_CRC != 0U)
|
|
/* Enable CRC Transmission */
|
|
if ((hspi->RxXferCount == 1U) && (hspi->Init.CRCCalculation == SPI_CRCCALCULATION_ENABLE))
|
|
{
|
|
SET_BIT(hspi->Instance->CR1, SPI_CR1_CRCNEXT);
|
|
}
|
|
#endif /* USE_SPI_CRC */
|
|
|
|
if (hspi->RxXferCount == 0U)
|
|
{
|
|
#if (USE_SPI_CRC != 0U)
|
|
if (hspi->Init.CRCCalculation == SPI_CRCCALCULATION_ENABLE)
|
|
{
|
|
hspi->RxISR = SPI_RxISR_8BITCRC;
|
|
return;
|
|
}
|
|
#endif /* USE_SPI_CRC */
|
|
SPI_CloseRx_ISR(hspi);
|
|
}
|
|
}
|
|
|
|
#if (USE_SPI_CRC != 0U)
|
|
/**
|
|
* @brief Manage the CRC 16-bit receive in Interrupt context.
|
|
* @param hspi pointer to a SPI_HandleTypeDef structure that contains
|
|
* the configuration information for SPI module.
|
|
* @retval None
|
|
*/
|
|
static void SPI_RxISR_16BITCRC(struct __SPI_HandleTypeDef *hspi)
|
|
{
|
|
__IO uint32_t tmpreg = 0U;
|
|
|
|
/* Read 16bit CRC to flush Data Register */
|
|
tmpreg = READ_REG(hspi->Instance->DR);
|
|
/* To avoid GCC warning */
|
|
UNUSED(tmpreg);
|
|
|
|
/* Disable RXNE and ERR interrupt */
|
|
__HAL_SPI_DISABLE_IT(hspi, (SPI_IT_RXNE | SPI_IT_ERR));
|
|
|
|
SPI_CloseRx_ISR(hspi);
|
|
}
|
|
#endif /* USE_SPI_CRC */
|
|
|
|
/**
|
|
* @brief Manage the 16-bit receive in Interrupt context.
|
|
* @param hspi pointer to a SPI_HandleTypeDef structure that contains
|
|
* the configuration information for SPI module.
|
|
* @retval None
|
|
*/
|
|
static void SPI_RxISR_16BIT(struct __SPI_HandleTypeDef *hspi)
|
|
{
|
|
*((uint16_t *)hspi->pRxBuffPtr) = (uint16_t)(hspi->Instance->DR);
|
|
hspi->pRxBuffPtr += sizeof(uint16_t);
|
|
hspi->RxXferCount--;
|
|
|
|
#if (USE_SPI_CRC != 0U)
|
|
/* Enable CRC Transmission */
|
|
if ((hspi->RxXferCount == 1U) && (hspi->Init.CRCCalculation == SPI_CRCCALCULATION_ENABLE))
|
|
{
|
|
SET_BIT(hspi->Instance->CR1, SPI_CR1_CRCNEXT);
|
|
}
|
|
#endif /* USE_SPI_CRC */
|
|
|
|
if (hspi->RxXferCount == 0U)
|
|
{
|
|
#if (USE_SPI_CRC != 0U)
|
|
if (hspi->Init.CRCCalculation == SPI_CRCCALCULATION_ENABLE)
|
|
{
|
|
hspi->RxISR = SPI_RxISR_16BITCRC;
|
|
return;
|
|
}
|
|
#endif /* USE_SPI_CRC */
|
|
SPI_CloseRx_ISR(hspi);
|
|
}
|
|
}
|
|
|
|
/**
|
|
* @brief Handle the data 8-bit transmit in Interrupt mode.
|
|
* @param hspi pointer to a SPI_HandleTypeDef structure that contains
|
|
* the configuration information for SPI module.
|
|
* @retval None
|
|
*/
|
|
static void SPI_TxISR_8BIT(struct __SPI_HandleTypeDef *hspi)
|
|
{
|
|
*(__IO uint8_t *)&hspi->Instance->DR = (*hspi->pTxBuffPtr);
|
|
hspi->pTxBuffPtr++;
|
|
hspi->TxXferCount--;
|
|
|
|
if (hspi->TxXferCount == 0U)
|
|
{
|
|
#if (USE_SPI_CRC != 0U)
|
|
if (hspi->Init.CRCCalculation == SPI_CRCCALCULATION_ENABLE)
|
|
{
|
|
/* Enable CRC Transmission */
|
|
SET_BIT(hspi->Instance->CR1, SPI_CR1_CRCNEXT);
|
|
}
|
|
#endif /* USE_SPI_CRC */
|
|
SPI_CloseTx_ISR(hspi);
|
|
}
|
|
}
|
|
|
|
/**
|
|
* @brief Handle the data 16-bit transmit in Interrupt mode.
|
|
* @param hspi pointer to a SPI_HandleTypeDef structure that contains
|
|
* the configuration information for SPI module.
|
|
* @retval None
|
|
*/
|
|
static void SPI_TxISR_16BIT(struct __SPI_HandleTypeDef *hspi)
|
|
{
|
|
/* Transmit data in 16 Bit mode */
|
|
hspi->Instance->DR = *((uint16_t *)hspi->pTxBuffPtr);
|
|
hspi->pTxBuffPtr += sizeof(uint16_t);
|
|
hspi->TxXferCount--;
|
|
|
|
if (hspi->TxXferCount == 0U)
|
|
{
|
|
#if (USE_SPI_CRC != 0U)
|
|
if (hspi->Init.CRCCalculation == SPI_CRCCALCULATION_ENABLE)
|
|
{
|
|
/* Enable CRC Transmission */
|
|
SET_BIT(hspi->Instance->CR1, SPI_CR1_CRCNEXT);
|
|
}
|
|
#endif /* USE_SPI_CRC */
|
|
SPI_CloseTx_ISR(hspi);
|
|
}
|
|
}
|
|
|
|
/**
|
|
* @brief Handle SPI Communication Timeout.
|
|
* @param hspi pointer to a SPI_HandleTypeDef structure that contains
|
|
* the configuration information for SPI module.
|
|
* @param Flag SPI flag to check
|
|
* @param State flag state to check
|
|
* @param Timeout Timeout duration
|
|
* @param Tickstart tick start value
|
|
* @retval HAL status
|
|
*/
|
|
static HAL_StatusTypeDef SPI_WaitFlagStateUntilTimeout(SPI_HandleTypeDef *hspi, uint32_t Flag, FlagStatus State,
|
|
uint32_t Timeout, uint32_t Tickstart)
|
|
{
|
|
__IO uint32_t count;
|
|
uint32_t tmp_timeout;
|
|
uint32_t tmp_tickstart;
|
|
|
|
/* Adjust Timeout value in case of end of transfer */
|
|
tmp_timeout = Timeout - (HAL_GetTick() - Tickstart);
|
|
tmp_tickstart = HAL_GetTick();
|
|
|
|
/* Calculate Timeout based on a software loop to avoid blocking issue if Systick is disabled */
|
|
count = tmp_timeout * ((SystemCoreClock * 32U) >> 20U);
|
|
|
|
while ((__HAL_SPI_GET_FLAG(hspi, Flag) ? SET : RESET) != State)
|
|
{
|
|
if (Timeout != HAL_MAX_DELAY)
|
|
{
|
|
if (((HAL_GetTick() - tmp_tickstart) >= tmp_timeout) || (tmp_timeout == 0U))
|
|
{
|
|
/* Disable the SPI and reset the CRC: the CRC value should be cleared
|
|
on both master and slave sides in order to resynchronize the master
|
|
and slave for their respective CRC calculation */
|
|
|
|
/* Disable TXE, RXNE and ERR interrupts for the interrupt process */
|
|
__HAL_SPI_DISABLE_IT(hspi, (SPI_IT_TXE | SPI_IT_RXNE | SPI_IT_ERR));
|
|
|
|
if ((hspi->Init.Mode == SPI_MODE_MASTER) && ((hspi->Init.Direction == SPI_DIRECTION_1LINE)
|
|
|| (hspi->Init.Direction == SPI_DIRECTION_2LINES_RXONLY)))
|
|
{
|
|
/* Disable SPI peripheral */
|
|
__HAL_SPI_DISABLE(hspi);
|
|
}
|
|
|
|
/* Reset CRC Calculation */
|
|
if (hspi->Init.CRCCalculation == SPI_CRCCALCULATION_ENABLE)
|
|
{
|
|
SPI_RESET_CRC(hspi);
|
|
}
|
|
|
|
hspi->State = HAL_SPI_STATE_READY;
|
|
|
|
/* Process Unlocked */
|
|
__HAL_UNLOCK(hspi);
|
|
|
|
return HAL_TIMEOUT;
|
|
}
|
|
/* If Systick is disabled or not incremented, deactivate timeout to go in disable loop procedure */
|
|
if (count == 0U)
|
|
{
|
|
tmp_timeout = 0U;
|
|
}
|
|
count--;
|
|
}
|
|
}
|
|
|
|
return HAL_OK;
|
|
}
|
|
|
|
/**
|
|
* @brief Handle SPI FIFO Communication Timeout.
|
|
* @param hspi pointer to a SPI_HandleTypeDef structure that contains
|
|
* the configuration information for SPI module.
|
|
* @param Fifo Fifo to check
|
|
* @param State Fifo state to check
|
|
* @param Timeout Timeout duration
|
|
* @param Tickstart tick start value
|
|
* @retval HAL status
|
|
*/
|
|
static HAL_StatusTypeDef SPI_WaitFifoStateUntilTimeout(SPI_HandleTypeDef *hspi, uint32_t Fifo, uint32_t State,
|
|
uint32_t Timeout, uint32_t Tickstart)
|
|
{
|
|
__IO uint32_t count;
|
|
uint32_t tmp_timeout;
|
|
uint32_t tmp_tickstart;
|
|
__IO uint8_t *ptmpreg8;
|
|
__IO uint8_t tmpreg8 = 0;
|
|
|
|
/* Adjust Timeout value in case of end of transfer */
|
|
tmp_timeout = Timeout - (HAL_GetTick() - Tickstart);
|
|
tmp_tickstart = HAL_GetTick();
|
|
|
|
/* Initialize the 8bit temporary pointer */
|
|
ptmpreg8 = (__IO uint8_t *)&hspi->Instance->DR;
|
|
|
|
/* Calculate Timeout based on a software loop to avoid blocking issue if Systick is disabled */
|
|
count = tmp_timeout * ((SystemCoreClock * 35U) >> 20U);
|
|
|
|
while ((hspi->Instance->SR & Fifo) != State)
|
|
{
|
|
if ((Fifo == SPI_SR_FRLVL) && (State == SPI_FRLVL_EMPTY))
|
|
{
|
|
/* Flush Data Register by a blank read */
|
|
tmpreg8 = *ptmpreg8;
|
|
/* To avoid GCC warning */
|
|
UNUSED(tmpreg8);
|
|
}
|
|
|
|
if (Timeout != HAL_MAX_DELAY)
|
|
{
|
|
if (((HAL_GetTick() - tmp_tickstart) >= tmp_timeout) || (tmp_timeout == 0U))
|
|
{
|
|
/* Disable the SPI and reset the CRC: the CRC value should be cleared
|
|
on both master and slave sides in order to resynchronize the master
|
|
and slave for their respective CRC calculation */
|
|
|
|
/* Disable TXE, RXNE and ERR interrupts for the interrupt process */
|
|
__HAL_SPI_DISABLE_IT(hspi, (SPI_IT_TXE | SPI_IT_RXNE | SPI_IT_ERR));
|
|
|
|
if ((hspi->Init.Mode == SPI_MODE_MASTER) && ((hspi->Init.Direction == SPI_DIRECTION_1LINE)
|
|
|| (hspi->Init.Direction == SPI_DIRECTION_2LINES_RXONLY)))
|
|
{
|
|
/* Disable SPI peripheral */
|
|
__HAL_SPI_DISABLE(hspi);
|
|
}
|
|
|
|
/* Reset CRC Calculation */
|
|
if (hspi->Init.CRCCalculation == SPI_CRCCALCULATION_ENABLE)
|
|
{
|
|
SPI_RESET_CRC(hspi);
|
|
}
|
|
|
|
hspi->State = HAL_SPI_STATE_READY;
|
|
|
|
/* Process Unlocked */
|
|
__HAL_UNLOCK(hspi);
|
|
|
|
return HAL_TIMEOUT;
|
|
}
|
|
/* If Systick is disabled or not incremented, deactivate timeout to go in disable loop procedure */
|
|
if (count == 0U)
|
|
{
|
|
tmp_timeout = 0U;
|
|
}
|
|
count--;
|
|
}
|
|
}
|
|
|
|
return HAL_OK;
|
|
}
|
|
|
|
/**
|
|
* @brief Handle the check of the RX transaction complete.
|
|
* @param hspi pointer to a SPI_HandleTypeDef structure that contains
|
|
* the configuration information for SPI module.
|
|
* @param Timeout Timeout duration
|
|
* @param Tickstart tick start value
|
|
* @retval HAL status
|
|
*/
|
|
static HAL_StatusTypeDef SPI_EndRxTransaction(SPI_HandleTypeDef *hspi, uint32_t Timeout, uint32_t Tickstart)
|
|
{
|
|
if ((hspi->Init.Mode == SPI_MODE_MASTER) && ((hspi->Init.Direction == SPI_DIRECTION_1LINE)
|
|
|| (hspi->Init.Direction == SPI_DIRECTION_2LINES_RXONLY)))
|
|
{
|
|
/* Disable SPI peripheral */
|
|
__HAL_SPI_DISABLE(hspi);
|
|
}
|
|
|
|
/* Control the BSY flag */
|
|
if (SPI_WaitFlagStateUntilTimeout(hspi, SPI_FLAG_BSY, RESET, Timeout, Tickstart) != HAL_OK)
|
|
{
|
|
SET_BIT(hspi->ErrorCode, HAL_SPI_ERROR_FLAG);
|
|
return HAL_TIMEOUT;
|
|
}
|
|
|
|
if ((hspi->Init.Mode == SPI_MODE_MASTER) && ((hspi->Init.Direction == SPI_DIRECTION_1LINE)
|
|
|| (hspi->Init.Direction == SPI_DIRECTION_2LINES_RXONLY)))
|
|
{
|
|
/* Empty the FRLVL fifo */
|
|
if (SPI_WaitFifoStateUntilTimeout(hspi, SPI_FLAG_FRLVL, SPI_FRLVL_EMPTY, Timeout, Tickstart) != HAL_OK)
|
|
{
|
|
SET_BIT(hspi->ErrorCode, HAL_SPI_ERROR_FLAG);
|
|
return HAL_TIMEOUT;
|
|
}
|
|
}
|
|
return HAL_OK;
|
|
}
|
|
|
|
/**
|
|
* @brief Handle the check of the RXTX or TX transaction complete.
|
|
* @param hspi SPI handle
|
|
* @param Timeout Timeout duration
|
|
* @param Tickstart tick start value
|
|
* @retval HAL status
|
|
*/
|
|
static HAL_StatusTypeDef SPI_EndRxTxTransaction(SPI_HandleTypeDef *hspi, uint32_t Timeout, uint32_t Tickstart)
|
|
{
|
|
/* Control if the TX fifo is empty */
|
|
if (SPI_WaitFifoStateUntilTimeout(hspi, SPI_FLAG_FTLVL, SPI_FTLVL_EMPTY, Timeout, Tickstart) != HAL_OK)
|
|
{
|
|
SET_BIT(hspi->ErrorCode, HAL_SPI_ERROR_FLAG);
|
|
return HAL_TIMEOUT;
|
|
}
|
|
|
|
/* Control the BSY flag */
|
|
if (SPI_WaitFlagStateUntilTimeout(hspi, SPI_FLAG_BSY, RESET, Timeout, Tickstart) != HAL_OK)
|
|
{
|
|
SET_BIT(hspi->ErrorCode, HAL_SPI_ERROR_FLAG);
|
|
return HAL_TIMEOUT;
|
|
}
|
|
|
|
/* Control if the RX fifo is empty */
|
|
if (SPI_WaitFifoStateUntilTimeout(hspi, SPI_FLAG_FRLVL, SPI_FRLVL_EMPTY, Timeout, Tickstart) != HAL_OK)
|
|
{
|
|
SET_BIT(hspi->ErrorCode, HAL_SPI_ERROR_FLAG);
|
|
return HAL_TIMEOUT;
|
|
}
|
|
|
|
return HAL_OK;
|
|
}
|
|
|
|
/**
|
|
* @brief Handle the end of the RXTX transaction.
|
|
* @param hspi pointer to a SPI_HandleTypeDef structure that contains
|
|
* the configuration information for SPI module.
|
|
* @retval None
|
|
*/
|
|
static void SPI_CloseRxTx_ISR(SPI_HandleTypeDef *hspi)
|
|
{
|
|
uint32_t tickstart;
|
|
|
|
/* Init tickstart for timeout management */
|
|
tickstart = HAL_GetTick();
|
|
|
|
/* Disable ERR interrupt */
|
|
__HAL_SPI_DISABLE_IT(hspi, SPI_IT_ERR);
|
|
|
|
/* Check the end of the transaction */
|
|
if (SPI_EndRxTxTransaction(hspi, SPI_DEFAULT_TIMEOUT, tickstart) != HAL_OK)
|
|
{
|
|
SET_BIT(hspi->ErrorCode, HAL_SPI_ERROR_FLAG);
|
|
}
|
|
|
|
#if (USE_SPI_CRC != 0U)
|
|
/* Check if CRC error occurred */
|
|
if (__HAL_SPI_GET_FLAG(hspi, SPI_FLAG_CRCERR) != RESET)
|
|
{
|
|
hspi->State = HAL_SPI_STATE_READY;
|
|
SET_BIT(hspi->ErrorCode, HAL_SPI_ERROR_CRC);
|
|
__HAL_SPI_CLEAR_CRCERRFLAG(hspi);
|
|
/* Call user error callback */
|
|
#if (USE_HAL_SPI_REGISTER_CALLBACKS == 1U)
|
|
hspi->ErrorCallback(hspi);
|
|
#else
|
|
HAL_SPI_ErrorCallback(hspi);
|
|
#endif /* USE_HAL_SPI_REGISTER_CALLBACKS */
|
|
}
|
|
else
|
|
{
|
|
#endif /* USE_SPI_CRC */
|
|
if (hspi->ErrorCode == HAL_SPI_ERROR_NONE)
|
|
{
|
|
if (hspi->State == HAL_SPI_STATE_BUSY_RX)
|
|
{
|
|
hspi->State = HAL_SPI_STATE_READY;
|
|
/* Call user Rx complete callback */
|
|
#if (USE_HAL_SPI_REGISTER_CALLBACKS == 1U)
|
|
hspi->RxCpltCallback(hspi);
|
|
#else
|
|
HAL_SPI_RxCpltCallback(hspi);
|
|
#endif /* USE_HAL_SPI_REGISTER_CALLBACKS */
|
|
}
|
|
else
|
|
{
|
|
hspi->State = HAL_SPI_STATE_READY;
|
|
/* Call user TxRx complete callback */
|
|
#if (USE_HAL_SPI_REGISTER_CALLBACKS == 1U)
|
|
hspi->TxRxCpltCallback(hspi);
|
|
#else
|
|
HAL_SPI_TxRxCpltCallback(hspi);
|
|
#endif /* USE_HAL_SPI_REGISTER_CALLBACKS */
|
|
}
|
|
}
|
|
else
|
|
{
|
|
hspi->State = HAL_SPI_STATE_READY;
|
|
/* Call user error callback */
|
|
#if (USE_HAL_SPI_REGISTER_CALLBACKS == 1U)
|
|
hspi->ErrorCallback(hspi);
|
|
#else
|
|
HAL_SPI_ErrorCallback(hspi);
|
|
#endif /* USE_HAL_SPI_REGISTER_CALLBACKS */
|
|
}
|
|
#if (USE_SPI_CRC != 0U)
|
|
}
|
|
#endif /* USE_SPI_CRC */
|
|
}
|
|
|
|
/**
|
|
* @brief Handle the end of the RX transaction.
|
|
* @param hspi pointer to a SPI_HandleTypeDef structure that contains
|
|
* the configuration information for SPI module.
|
|
* @retval None
|
|
*/
|
|
static void SPI_CloseRx_ISR(SPI_HandleTypeDef *hspi)
|
|
{
|
|
/* Disable RXNE and ERR interrupt */
|
|
__HAL_SPI_DISABLE_IT(hspi, (SPI_IT_RXNE | SPI_IT_ERR));
|
|
|
|
/* Check the end of the transaction */
|
|
if (SPI_EndRxTransaction(hspi, SPI_DEFAULT_TIMEOUT, HAL_GetTick()) != HAL_OK)
|
|
{
|
|
SET_BIT(hspi->ErrorCode, HAL_SPI_ERROR_FLAG);
|
|
}
|
|
hspi->State = HAL_SPI_STATE_READY;
|
|
|
|
#if (USE_SPI_CRC != 0U)
|
|
/* Check if CRC error occurred */
|
|
if (__HAL_SPI_GET_FLAG(hspi, SPI_FLAG_CRCERR) != RESET)
|
|
{
|
|
SET_BIT(hspi->ErrorCode, HAL_SPI_ERROR_CRC);
|
|
__HAL_SPI_CLEAR_CRCERRFLAG(hspi);
|
|
/* Call user error callback */
|
|
#if (USE_HAL_SPI_REGISTER_CALLBACKS == 1U)
|
|
hspi->ErrorCallback(hspi);
|
|
#else
|
|
HAL_SPI_ErrorCallback(hspi);
|
|
#endif /* USE_HAL_SPI_REGISTER_CALLBACKS */
|
|
}
|
|
else
|
|
{
|
|
#endif /* USE_SPI_CRC */
|
|
if (hspi->ErrorCode == HAL_SPI_ERROR_NONE)
|
|
{
|
|
/* Call user Rx complete callback */
|
|
#if (USE_HAL_SPI_REGISTER_CALLBACKS == 1U)
|
|
hspi->RxCpltCallback(hspi);
|
|
#else
|
|
HAL_SPI_RxCpltCallback(hspi);
|
|
#endif /* USE_HAL_SPI_REGISTER_CALLBACKS */
|
|
}
|
|
else
|
|
{
|
|
/* Call user error callback */
|
|
#if (USE_HAL_SPI_REGISTER_CALLBACKS == 1U)
|
|
hspi->ErrorCallback(hspi);
|
|
#else
|
|
HAL_SPI_ErrorCallback(hspi);
|
|
#endif /* USE_HAL_SPI_REGISTER_CALLBACKS */
|
|
}
|
|
#if (USE_SPI_CRC != 0U)
|
|
}
|
|
#endif /* USE_SPI_CRC */
|
|
}
|
|
|
|
/**
|
|
* @brief Handle the end of the TX transaction.
|
|
* @param hspi pointer to a SPI_HandleTypeDef structure that contains
|
|
* the configuration information for SPI module.
|
|
* @retval None
|
|
*/
|
|
static void SPI_CloseTx_ISR(SPI_HandleTypeDef *hspi)
|
|
{
|
|
uint32_t tickstart;
|
|
|
|
/* Init tickstart for timeout management*/
|
|
tickstart = HAL_GetTick();
|
|
|
|
/* Disable TXE and ERR interrupt */
|
|
__HAL_SPI_DISABLE_IT(hspi, (SPI_IT_TXE | SPI_IT_ERR));
|
|
|
|
/* Check the end of the transaction */
|
|
if (SPI_EndRxTxTransaction(hspi, SPI_DEFAULT_TIMEOUT, tickstart) != HAL_OK)
|
|
{
|
|
SET_BIT(hspi->ErrorCode, HAL_SPI_ERROR_FLAG);
|
|
}
|
|
|
|
/* Clear overrun flag in 2 Lines communication mode because received is not read */
|
|
if (hspi->Init.Direction == SPI_DIRECTION_2LINES)
|
|
{
|
|
__HAL_SPI_CLEAR_OVRFLAG(hspi);
|
|
}
|
|
|
|
hspi->State = HAL_SPI_STATE_READY;
|
|
if (hspi->ErrorCode != HAL_SPI_ERROR_NONE)
|
|
{
|
|
/* Call user error callback */
|
|
#if (USE_HAL_SPI_REGISTER_CALLBACKS == 1U)
|
|
hspi->ErrorCallback(hspi);
|
|
#else
|
|
HAL_SPI_ErrorCallback(hspi);
|
|
#endif /* USE_HAL_SPI_REGISTER_CALLBACKS */
|
|
}
|
|
else
|
|
{
|
|
/* Call user Rx complete callback */
|
|
#if (USE_HAL_SPI_REGISTER_CALLBACKS == 1U)
|
|
hspi->TxCpltCallback(hspi);
|
|
#else
|
|
HAL_SPI_TxCpltCallback(hspi);
|
|
#endif /* USE_HAL_SPI_REGISTER_CALLBACKS */
|
|
}
|
|
}
|
|
|
|
/**
|
|
* @brief Handle abort a Rx transaction.
|
|
* @param hspi pointer to a SPI_HandleTypeDef structure that contains
|
|
* the configuration information for SPI module.
|
|
* @retval None
|
|
*/
|
|
static void SPI_AbortRx_ISR(SPI_HandleTypeDef *hspi)
|
|
{
|
|
__IO uint32_t count;
|
|
|
|
/* Disable SPI Peripheral */
|
|
__HAL_SPI_DISABLE(hspi);
|
|
|
|
count = SPI_DEFAULT_TIMEOUT * (SystemCoreClock / 24U / 1000U);
|
|
|
|
/* Disable RXNEIE interrupt */
|
|
CLEAR_BIT(hspi->Instance->CR2, (SPI_CR2_RXNEIE));
|
|
|
|
/* Check RXNEIE is disabled */
|
|
do
|
|
{
|
|
if (count == 0U)
|
|
{
|
|
SET_BIT(hspi->ErrorCode, HAL_SPI_ERROR_ABORT);
|
|
break;
|
|
}
|
|
count--;
|
|
} while (HAL_IS_BIT_SET(hspi->Instance->CR2, SPI_CR2_RXNEIE));
|
|
|
|
/* Control the BSY flag */
|
|
if (SPI_WaitFlagStateUntilTimeout(hspi, SPI_FLAG_BSY, RESET, SPI_DEFAULT_TIMEOUT, HAL_GetTick()) != HAL_OK)
|
|
{
|
|
hspi->ErrorCode = HAL_SPI_ERROR_ABORT;
|
|
}
|
|
|
|
/* Empty the FRLVL fifo */
|
|
if (SPI_WaitFifoStateUntilTimeout(hspi, SPI_FLAG_FRLVL, SPI_FRLVL_EMPTY, SPI_DEFAULT_TIMEOUT, HAL_GetTick()) != HAL_OK)
|
|
{
|
|
hspi->ErrorCode = HAL_SPI_ERROR_ABORT;
|
|
}
|
|
|
|
hspi->State = HAL_SPI_STATE_ABORT;
|
|
}
|
|
|
|
/**
|
|
* @brief Handle abort a Tx or Rx/Tx transaction.
|
|
* @param hspi pointer to a SPI_HandleTypeDef structure that contains
|
|
* the configuration information for SPI module.
|
|
* @retval None
|
|
*/
|
|
static void SPI_AbortTx_ISR(SPI_HandleTypeDef *hspi)
|
|
{
|
|
__IO uint32_t count;
|
|
|
|
count = SPI_DEFAULT_TIMEOUT * (SystemCoreClock / 24U / 1000U);
|
|
|
|
/* Disable TXEIE interrupt */
|
|
CLEAR_BIT(hspi->Instance->CR2, (SPI_CR2_TXEIE));
|
|
|
|
/* Check TXEIE is disabled */
|
|
do
|
|
{
|
|
if (count == 0U)
|
|
{
|
|
SET_BIT(hspi->ErrorCode, HAL_SPI_ERROR_ABORT);
|
|
break;
|
|
}
|
|
count--;
|
|
} while (HAL_IS_BIT_SET(hspi->Instance->CR2, SPI_CR2_TXEIE));
|
|
|
|
if (SPI_EndRxTxTransaction(hspi, SPI_DEFAULT_TIMEOUT, HAL_GetTick()) != HAL_OK)
|
|
{
|
|
hspi->ErrorCode = HAL_SPI_ERROR_ABORT;
|
|
}
|
|
|
|
/* Disable SPI Peripheral */
|
|
__HAL_SPI_DISABLE(hspi);
|
|
|
|
/* Empty the FRLVL fifo */
|
|
if (SPI_WaitFifoStateUntilTimeout(hspi, SPI_FLAG_FRLVL, SPI_FRLVL_EMPTY, SPI_DEFAULT_TIMEOUT, HAL_GetTick()) != HAL_OK)
|
|
{
|
|
hspi->ErrorCode = HAL_SPI_ERROR_ABORT;
|
|
}
|
|
|
|
/* Check case of Full-Duplex Mode and disable directly RXNEIE interrupt */
|
|
if (HAL_IS_BIT_SET(hspi->Instance->CR2, SPI_CR2_RXNEIE))
|
|
{
|
|
/* Disable RXNEIE interrupt */
|
|
CLEAR_BIT(hspi->Instance->CR2, (SPI_CR2_RXNEIE));
|
|
|
|
/* Check RXNEIE is disabled */
|
|
do
|
|
{
|
|
if (count == 0U)
|
|
{
|
|
SET_BIT(hspi->ErrorCode, HAL_SPI_ERROR_ABORT);
|
|
break;
|
|
}
|
|
count--;
|
|
} while (HAL_IS_BIT_SET(hspi->Instance->CR2, SPI_CR2_RXNEIE));
|
|
|
|
/* Control the BSY flag */
|
|
if (SPI_WaitFlagStateUntilTimeout(hspi, SPI_FLAG_BSY, RESET, SPI_DEFAULT_TIMEOUT, HAL_GetTick()) != HAL_OK)
|
|
{
|
|
hspi->ErrorCode = HAL_SPI_ERROR_ABORT;
|
|
}
|
|
|
|
/* Empty the FRLVL fifo */
|
|
if (SPI_WaitFifoStateUntilTimeout(hspi, SPI_FLAG_FRLVL, SPI_FRLVL_EMPTY, SPI_DEFAULT_TIMEOUT, HAL_GetTick()) != HAL_OK)
|
|
{
|
|
hspi->ErrorCode = HAL_SPI_ERROR_ABORT;
|
|
}
|
|
}
|
|
hspi->State = HAL_SPI_STATE_ABORT;
|
|
}
|
|
|
|
/**
|
|
* @}
|
|
*/
|
|
|
|
#endif /* HAL_SPI_MODULE_ENABLED */
|
|
|
|
/**
|
|
* @}
|
|
*/
|
|
|
|
/**
|
|
* @}
|
|
*/
|
|
|