327 lines
10 KiB
C
327 lines
10 KiB
C
/************************************************************
|
||
Copyright (C), 2025, cerlink Tech. Co., Ltd.
|
||
FileName: drv_adc.c
|
||
Author: dufresne Version : 1.0 Date:2025.09.15
|
||
Description: // 模块描述
|
||
Version: // 版本信息
|
||
Function List: // 主要函数及其功能
|
||
1. -------
|
||
History: // 历史修改记录
|
||
<author> <time> <version > <desc>
|
||
David 96/10/12 1.0 build this moudle
|
||
***********************************************************/
|
||
|
||
#include "drv_adc.h"
|
||
|
||
|
||
#ifdef DMAX
|
||
|
||
/*全局声明区*/
|
||
uint16_t USER_ADC_DMA_DATA_BUFF[16] = {0};
|
||
|
||
#endif
|
||
|
||
bool filter_v_flag = 0;//滤波开启标志位，全局改变一次
|
||
bool filter_i_flag = 0;//滤波开启标志位，全局改变一次
|
||
bool filter_t_flag = 0;//滤波开启标志位，全局改变一次
|
||
|
||
|
||
|
||
/* ---------------------------------------------------配置---------------------------------------------------- */
|
||
|
||
void adc_init(void)
|
||
{
|
||
adc_rcu_config();
|
||
adc_gpio_config();
|
||
|
||
#ifdef DMAX
|
||
adc_dma_config();
|
||
#endif
|
||
|
||
adc_config();
|
||
|
||
#ifdef ADCX_IRQn
|
||
adc_interrupt_int();
|
||
#endif
|
||
|
||
}
|
||
/* 时钟+GPIO */
|
||
void adc_rcu_config(void)
|
||
{
|
||
/* 启用ADC1时钟 */
|
||
rcu_periph_clock_enable(RCU_ADC1);
|
||
#ifdef DMAX
|
||
/* peripheral clock enable */
|
||
rcu_periph_clock_enable(RCU_DMA1);//ADC只能用DMA1
|
||
#endif
|
||
/* 启用GPIOC时钟 */
|
||
rcu_periph_clock_enable(RCU_GPIOC);
|
||
adc_clock_config(ADC_ADCCK_PCLK2_DIV4);
|
||
}
|
||
|
||
void adc_gpio_config(void)
|
||
{
|
||
/* 配置ADC引脚为模拟输入模式 */
|
||
gpio_mode_set(ADC_GPIO_PORT, GPIO_MODE_ANALOG, GPIO_PUPD_NONE, VOLTAGE_ADC_PIN);
|
||
gpio_mode_set(ADC_GPIO_PORT, GPIO_MODE_ANALOG, GPIO_PUPD_NONE, CURRENT_ADC_PIN);
|
||
}
|
||
|
||
#ifdef DMAX
|
||
|
||
/* DMA配置 */
|
||
void adc_dma_config(void)
|
||
{
|
||
/* ADC_DMA_channel configuration */
|
||
dma_single_data_parameter_struct dma_single_data_parameter; //这里使用单数据模式，每次只传输一个数据单元，因为总数据量不大，且数据个数不固定
|
||
|
||
/* ADC DMA_channel configuration */
|
||
dma_deinit (DMA1, USER_DMA_ADC_CHANNEL);
|
||
|
||
/* initialize DMA single data mode */
|
||
dma_single_data_parameter.periph_addr = (uint32_t)(&ADC_RDATA(ADCX)); //配置外设数据源地址，宏决定ADCx
|
||
dma_single_data_parameter.periph_inc = DMA_PERIPH_INCREASE_DISABLE; //关闭外设增量，只需要每次对该数据源寄存器访问
|
||
dma_single_data_parameter.memory0_addr = (uint32_t)USER_ADC_DMA_DATA_BUFF; //先写死，然后外部用的话需要extern
|
||
dma_single_data_parameter.memory_inc = DMA_MEMORY_INCREASE_ENABLE; //开启内存增量，以存放不同通道的ADC数据
|
||
dma_single_data_parameter.periph_memory_width = DMA_PERIPH_WIDTH_16BIT; //ADC数据为16位的寄存器，数据目的地为16位
|
||
dma_single_data_parameter.circular_mode = DMA_CIRCULAR_MODE_ENABLE; //循环模式，由ADC通知DMA进行
|
||
dma_single_data_parameter.direction = DMA_PERIPH_TO_MEMORY; //ADC外设到RAM全局变量 DMA外设到内存模式开启
|
||
dma_single_data_parameter.number = CHANNEL_LENGTH; //宏决定传输个数
|
||
dma_single_data_parameter.priority = DMA_PRIORITY_ULTRA_HIGH; //优先级设为超高，可改用宏
|
||
dma_single_data_mode_init (DMAX, USER_DMA_ADC_CHANNEL, &dma_single_data_parameter);
|
||
/* 配置 dma 子连接 */
|
||
dma_channel_subperipheral_select (DMAX, USER_DMA_ADC_CHANNEL, USER_DMA_ADC_SUBPERI);
|
||
|
||
/* enable DMA circulation mode */
|
||
dma_circulation_enable (DMAX, USER_DMA_ADC_CHANNEL);// 开启循环模式
|
||
|
||
/* enable DMA it */
|
||
dma_interrupt_enable (DMAX,USER_DMA_ADC_CHANNEL,DMA_INT_FTF);//DMA传输完成标志位 打开全部完成中断 4
|
||
// dma_interrupt_enable (DMAX,USER_DMA_ADC_CHANNEL,DMA_INT_TAE);//传输错误中断使能位 2
|
||
// dma_interrupt_enable (DMAX,USER_DMA_ADC_CHANNEL,DMA_INT_FEE);// 7
|
||
nvic_irq_enable (DMA_ADC_IRQn, DMA_ADC_PRIORITY_PRE, DMA_ADC_PRIORITY_SUB);
|
||
|
||
dma_channel_enable (DMAX, USER_DMA_ADC_CHANNEL);// enable DMA channel
|
||
}
|
||
|
||
|
||
/**
|
||
* @brief 根据转换序列的序列号，获取转换序列中的ADC测量值
|
||
* @param 配置ADC通道结构体中的成员序号
|
||
* @return 测量并转换后的值
|
||
*/
|
||
|
||
uint16_t BSP_ADCDataAcquire(uint8_t _index)
|
||
{
|
||
return USER_ADC_DMA_DATA_BUFF[_index];
|
||
}
|
||
|
||
/*
|
||
*****************************************************************************
|
||
* 函数名 : DMA1_Channel0_IRQHandler
|
||
* 功能说明: DMA_ADC中断服务回调函数
|
||
* 形 参 : 无
|
||
* 返回值 : 无
|
||
*****************************************************************************
|
||
*/
|
||
__weak void DMA1_Channel0_IRQHandler(void)
|
||
{
|
||
|
||
}
|
||
#endif
|
||
|
||
|
||
void adc_config(void)
|
||
{
|
||
adc_deinit();// 复位ADC配置（可选，但建议初始化时做一次）
|
||
|
||
adc_special_function_config (ADCX, ADC_SCAN_MODE, SCAN_STATUS);// 扫描模式
|
||
adc_special_function_config (ADCX, ADC_CONTINUOUS_MODE, CONTINUOUS_STATUS);// 连续模式
|
||
|
||
adc_data_alignment_config (ADCX, ADC_DATAALIGN_RIGHT);// 配置数据对齐方式为右对齐
|
||
adc_resolution_config (ADCX, ADC_RESOLUTION_12B);// 配置ADC分辨率：12位
|
||
|
||
/* 设置转换通道序列 */
|
||
adc_channel_length_config (ADCX, SEQUENCE_CHANNEL, CHANNEL_LENGTH);// 配置规则序列的长度：2个通道
|
||
|
||
if (SEQUENCE_CHANNEL == ADC_INSERTED_CHANNEL)
|
||
{
|
||
//通道注入顺序
|
||
/* 配置规则序列：序号0是电压通道，序号1是电流通道 */
|
||
adc_inserted_channel_config (ADCX, 0, VOLTAGE_ADC_CHANNEL, ADC_SAMPLETIME_480);//电压
|
||
adc_inserted_channel_config (ADCX, 1, CURRENT_ADC_CHANNEL, ADC_SAMPLETIME_480);//电流
|
||
}
|
||
#ifdef DMAX
|
||
adc_routine_channel_config(ADCX, 0, VOLTAGE_ADC_CHANNEL, ADC_SAMPLETIME_480);
|
||
adc_routine_channel_config(ADCX, 1, CURRENT_ADC_CHANNEL, ADC_SAMPLETIME_480);
|
||
#endif
|
||
|
||
/* 使能外部触发：这里使用软件触发，所以先禁用硬件触发 */
|
||
// adc_external_trigger_source_config(ADCX, SEQUENCE_CHANNEL, ADC_EXTTRIG_ROUTINE_T0_CH0);
|
||
adc_external_trigger_config (ADCX, SEQUENCE_CHANNEL, DISABLE);
|
||
|
||
#ifdef DMAX
|
||
/* ADC dma config */
|
||
adc_dma_request_after_last_enable (ADCX);
|
||
adc_dma_mode_enable (ADCX);
|
||
#endif
|
||
adc_enable (ADCX); // 开启ADC
|
||
rt_thread_mdelay(50); // 等待ADC稳定后续接校准
|
||
adc_calibration_enable (ADCX); // 执行ADC自校准
|
||
|
||
#ifdef DMAX
|
||
adc_software_trigger_enable (ADCX, SEQUENCE_CHANNEL); // 软件触发使能 后续接读取
|
||
#endif
|
||
}
|
||
|
||
#ifdef ADCX_IRQn
|
||
void adc_interrupt_int(void)
|
||
{
|
||
adc_interrupt_enable (ADCX, ADC_INT_EOC);
|
||
nvic_irq_enable (ADCX_IRQn, ADCX_PRIORITY_PRE, ADCX_PRIORITY_SUB);
|
||
|
||
}
|
||
#endif
|
||
|
||
/* ---------------------------------------------------采集---------------------------------------------------- */
|
||
|
||
// adc电压采集
|
||
float ptz_Voltage_collect_adc1_task()
|
||
{
|
||
static float adc1_v[LB_V_TIMES];
|
||
static float curadc1_out_v;
|
||
static uint8_t adc1_v_num = 0;
|
||
uint16_t value_V = 0;
|
||
|
||
if (SEQUENCE_CHANNEL == ADC_ROUTINE_CHANNEL)
|
||
{
|
||
adc_routine_channel_config(ADCX, 0, VOLTAGE_ADC_CHANNEL, ADC_SAMPLETIME_480);
|
||
}
|
||
|
||
adc_software_trigger_enable(ADCX, SEQUENCE_CHANNEL);// 软件触发使能 后续接读取
|
||
if (SEQUENCE_CHANNEL == ADC_ROUTINE_CHANNEL)
|
||
{
|
||
while(adc_flag_get(ADCX, ADC_FLAG_EOC) == RESET); // 等待转换结束
|
||
adc_flag_clear(ADCX, ADC_FLAG_EOC);
|
||
value_V = adc_routine_data_read(ADCX); // 读取规则组数据寄存器
|
||
}
|
||
else if (SEQUENCE_CHANNEL == ADC_INSERTED_CHANNEL)
|
||
{
|
||
while(adc_flag_get(ADCX, ADC_FLAG_EOIC) == RESET); // 等待转换结束
|
||
adc_flag_clear(ADCX, ADC_FLAG_EOIC);
|
||
value_V = adc_inserted_data_read(ADCX, ADC_INSERTED_CHANNEL_0); // 读取注入组数据寄存器
|
||
}
|
||
/* 间接测量，11倍分压/放大 */
|
||
adc1_v[adc1_v_num] = (float)value_V / 4095.0 * 3.3;
|
||
|
||
adc1_v_num++;
|
||
if(adc1_v_num >= LB_V_TIMES)
|
||
{
|
||
adc1_v_num = 0;
|
||
filter_v_flag = 1;
|
||
}
|
||
|
||
if (filter_v_flag)
|
||
{
|
||
return Filtering(adc1_v, LB_V_TIMES, LB_V_DEL);
|
||
}
|
||
|
||
return 0;
|
||
}
|
||
|
||
|
||
// adc电流采集
|
||
float ptz_Current_collect_adc1_task()
|
||
{
|
||
static float adc1_i[LB_I_TIMES];
|
||
static float curadc1_out_i;
|
||
static uint8_t adc1_i_num = 0;
|
||
uint16_t value_I = 0;
|
||
if (SEQUENCE_CHANNEL == ADC_ROUTINE_CHANNEL)
|
||
{
|
||
adc_routine_channel_config(ADCX, 0, CURRENT_ADC_CHANNEL, ADC_SAMPLETIME_480);
|
||
}
|
||
|
||
adc_software_trigger_enable(ADCX, SEQUENCE_CHANNEL);// 软件触发使能 后续接读取
|
||
|
||
if (SEQUENCE_CHANNEL == ADC_ROUTINE_CHANNEL)
|
||
{
|
||
while (adc_flag_get(ADCX, ADC_FLAG_EOC) == RESET); // 等待转换结束->等到SET
|
||
adc_flag_clear(ADCX, ADC_FLAG_EOC);
|
||
value_I = adc_routine_data_read(ADCX); // 读取规则组数据寄存器
|
||
}
|
||
else if (SEQUENCE_CHANNEL == ADC_INSERTED_CHANNEL)
|
||
{
|
||
while (adc_flag_get(ADCX, ADC_FLAG_EOIC) == RESET); // 等待转换结束
|
||
adc_flag_clear(ADCX, ADC_FLAG_EOIC);
|
||
value_I = adc_inserted_data_read(ADCX, ADC_INSERTED_CHANNEL_1); // 读取注入组数据寄存器
|
||
}
|
||
|
||
/* 间接测量，11倍分压/放大 */
|
||
adc1_i[adc1_i_num] = (((float)value_I / 4095.0 * 3.3) - 3.3 / 2) / 0.132;
|
||
|
||
adc1_i_num++;
|
||
if(adc1_i_num >= LB_I_TIMES)
|
||
{
|
||
adc1_i_num = 0;
|
||
filter_i_flag = 1;
|
||
}
|
||
|
||
if (filter_i_flag)
|
||
{
|
||
return Filtering(adc1_i, LB_I_TIMES, LB_I_DEL);
|
||
}
|
||
return 0;
|
||
}
|
||
|
||
|
||
//温度采集
|
||
float ptz_temperature_collect_tmp75_task()
|
||
{
|
||
static float tmp75[5];
|
||
static unsigned char tmp75_num;
|
||
static float curtmp75_out;
|
||
|
||
tmp75[tmp75_num] = tmp75_read_temp();
|
||
tmp75_num ++;
|
||
|
||
if(tmp75_num >= LB_T_TIMES)
|
||
{
|
||
tmp75_num = 0;
|
||
filter_t_flag = 1;
|
||
}
|
||
if (filter_t_flag)
|
||
{
|
||
return Filtering(tmp75, LB_T_TIMES, LB_T_DEL);
|
||
}
|
||
return 0;
|
||
}
|
||
|
||
|
||
float Filtering(float *filter, uint8_t filterlens, uint8_t filterdel)
|
||
{
|
||
uint8_t j,k;
|
||
float tem;
|
||
float curadc = 0;
|
||
|
||
for(j = 0; j < filterlens - 1; j++)// 采样值由小到大排列
|
||
{
|
||
for(k = 0; k < filterlens - j - 1; k++)
|
||
{
|
||
if(filter[k] > filter[k + 1])
|
||
{
|
||
tem = filter[k];
|
||
filter[k] = filter[k + 1];
|
||
filter[k + 1] = tem;
|
||
}
|
||
}
|
||
}
|
||
|
||
for(uint8_t i = filterdel; i < filterlens - filterdel; i++)
|
||
{
|
||
curadc = curadc + filter[i];
|
||
}
|
||
curadc = curadc / ((float)(filterlens - filterdel * 2));// 去掉一个最大值和一个最小值求平均值
|
||
return curadc;
|
||
}
|
||
|