更改ADC部分

App/inc/inflash.h

@@ -50,14 +50,15 @@ typedef struct _config_info{
     uint16_t floatI;                        /* 电压高于该(ConstantVoltageV / 100)且电流低于（FloatI / 100）进行浮充充电 */
     uint16_t startSolarOpenCircuitV;        /* 太阳能板开路电压高于该(电压 / 100)开始充电 */
     uint16_t stopSolarOpenCircuitV;         /* 太阳能板开路电压高于该(电压 / 100)停止充电 */
-    uint16_t noBatteryChargeV;              /* 没有电池时的输出电压 */
+    uint16_t constantVoltageChargeV;        /* 恒压充电时的输出电压 */
+    uint16_t trickleChargeC;                /* 涓流充电电流 */
     uint16_t FloatTime;                     /* 浮充时间(秒) */
     uint16_t checkSolarOpenCircuitVTime;    /* 启动任务中太阳能板开路电压检测时间 */
     uint16_t registerRefreshTime;           /* 寄存器数据刷新时间 */
     uint16_t resRefreshTime;                /* 线阻计算间隔时长 */
     uint16_t sensorEnableBroadcastTime;     /* 传感器运行再次注册的间隔 */
     uint16_t HighSideMosTemperature_stop;   /* 当上桥温度达到该值时，停止输出 */
-    uint16_t HighSideMosTemperature_end;    /* 当上桥温度上升到该值时，输出稳定在12V，降低功率运行 */
+    uint16_t HighSideMosTemperature_end;    /* 当上桥温度上升到该值时，降低功率运行 */
     uint16_t HighSideMosTemperature_start;  /* 当上桥温度降低到该值时，按照正常情况输出 */
     uint8_t  end_Flag;                      /* 结束标志 */
 }config_info;

App/inc/mppt_control.h

@@ -18,7 +18,7 @@ void MpptMode(void);
 void mppt_constantVoltage(float InVoltage);
 void test(void);
 void printf_data(void);
-float_t get_capturedata(float_t (*fun)(void));
+//float_t get_capturedata(float_t (*fun)(void));
 uint16_t get_mpptMode(void);
 
 #endif /* APP_INC_MPPT_CONTROL_H_ */

App/inc/sl_protocol.h

@@ -30,13 +30,14 @@ typedef enum
    SL_Register_address                      = 0x0001,  /* 地址  */
    SL_Register_Access_Node_Type             = 0x0002,  /* 接入节点类型   */
    SL_Register_Communication_Methods        = 0x0003,  /* 通信方式   */
-   SL_Register_Battery_Voltage              = 0x0100,  /* 电池电压   */
+   SL_Register_Output_Voltage               = 0x0100,  /* 输出电压   */
-   SL_Register_Charg_Current                = 0x0101,  /* 充电电流（流向电池+负载）   */
+   SL_Register_Battery_Voltage              = 0x0101,  /* 电池电压   */
-   SL_Register_Discharg_Current             = 0x0102,  /* 放电电流（流向负载）   */
+   SL_Register_Charg_Current                = 0x0102,  /* 充电电流（流向电池+负载）   */
-   SL_Register_Solar_Open_Circuit_Voltage   = 0x0103,  /* 太阳能开路电压 */
+   SL_Register_Discharg_Current             = 0x0103,  /* 放电电流（流向负载）   */
-   SL_Register_HighSideMos_Temperature      = 0x0104,  /* 高端mos的温度 */
+   SL_Register_Solar_Open_Circuit_Voltage   = 0x0104,  /* 太阳能开路电压 */
-   SL_Register_DischargMos_State            = 0x0105,  /* 放电mos的状态 */
+   SL_Register_HighSideMos_Temperature      = 0x0105,  /* 高端mos的温度 */
-   SL_Register_MPPT_Mode                    = 0x0106,  /* 工作模式 */
+   SL_Register_DischargMos_State            = 0x0106,  /* 放电mos的状态 */
+   SL_Register_MPPT_Mode                    = 0x0107,  /* 工作模式 */
 }SL_Mppt_MsgRegister;
 
 /* 注册状态 */
@@ -223,9 +224,11 @@ typedef struct _SL_Mppt_para{
   uint8_t  address[7];                  /* 地址  */
   uint16_t Access_Node_Type;            /* 接入节点类型  */
   uint16_t Communication_Methods;       /* 通信方式  */
+  float_t Output_Voltage;               /* 输出电压 */
   float_t Battery_Voltage;              /* 电池电压  */
   float_t Charg_Current;                /* 充电电流（流向电池+负载）   */
   float_t Discharg_Current;             /* 放电电流（流向负载）   */
+  float_t Input_Voltage;                /* 太阳能开路电压  */
   float_t Solar_Open_Circuit_Voltage;   /* 太阳能开路电压  */
   float_t HighSideMos_Temperature;      /* 高端mos的温度 */
   uint16_t DischargMos_State;           /* 放电mos的状态 */

App/src/collect_Conversion.c

@@ -12,6 +12,10 @@
 #include <stdlib.h>
 #include <limits.h>
 
+#include "uart_dev.h"
+#include <string.h>
+
+#define ONLYPOWER 1
 
 #define CHG_CURR        ADC_Channel_1
 #define PV_VOLT_OUT     ADC_Channel_2
@@ -23,14 +27,38 @@
 
 //#define enable_Printf_VI
 
+#ifdef ONLYPOWER
+/* 光伏充电输出电流比例，放大倍数*电阻 */
+const float P_CHG_CURR = (1.0 / (50 * 0.005 / 2));
+/* 光伏充电输出电压比例，分压系数（放电时采集不准） */
+//const float P_PV_VOLT_OUT = (47.0 + 10.0) / 10.0;
+const float P_PV_VOLT_OUT = (47.0 + 4.7) / 4.7;
+/* 放电电流采集电流倍数 */
+const float P_DSG_CURR = (1.0 / (50 * 0.005 / 2));
+///* 光伏1开路输出电压比例 */
+//const float P_PV1_VOLT_IN = (100 + 4.7) / 4.7;
+const float P_PV1_VOLT_IN = (100.0 + 4.7) / 4.7;
+/* 光伏1开路输出电压比例 */
+//const float P_PV1_VOLT_IN = (47 + 4.7) / 4.7;
+/* 系统电源电压比例 */
+const float P_PV_VOLT_IN1 = (47 + 4.7) / 4.7;
+/* 温度采集比例 */
+//const float P_MOSFET_TEMPER = 0;
+/* 光伏2开路输出电压比例 */
+const float P_PV2_VOLT_IN = (100.0 + 4.7) / 4.7;
+#endif
+
+#ifndef ONLYPOWER
 /* 光伏充电输出电流比例，放大倍数*电阻 */
 const float P_CHG_CURR = (1.0 / (50 * 0.005));
 /* 光伏充电输出电压比例，分压系数（放电时采集不准） */
-const float P_PV_VOLT_OUT = (47.0 + 10.0) / 10.0;
+//const float P_PV_VOLT_OUT = (47.0 + 10.0) / 10.0;
+const float P_PV_VOLT_OUT = (47.0 + 4.7) / 4.7;
 /* 放电电流采集电流倍数 */
 const float P_DSG_CURR = (1.0 / (50 * 0.005));
 ///* 光伏1开路输出电压比例 */
-const float P_PV1_VOLT_IN = (100 + 4.7) / 4.7;
+//const float P_PV1_VOLT_IN = (100 + 4.7) / 4.7;
+const float P_PV1_VOLT_IN = (47.0 + 4.7) / 4.7;
 /* 光伏1开路输出电压比例 */
 //const float P_PV1_VOLT_IN = (47 + 4.7) / 4.7;
 /* 系统电源电压比例 */
@@ -39,42 +67,116 @@ const float P_PV_VOLT_IN1 = (47 + 4.7) / 4.7;
 //const float P_MOSFET_TEMPER = 0;
 /* 光伏2开路输出电压比例 */
 const float P_PV2_VOLT_IN = (47 + 4.7) / 4.7;
+#endif
 
 /* 温度的adc值的个数 */
 #define  mosTemperADCLen 241
+///* 温度  */
+//const uint16_t mosTemperADC[mosTemperADCLen] = {
+//        3707, 3697, 3687, 3676, 3665, 3654, 3643, 3632, 3620, 3608,     /* -20  -   -15.5 ℃ */
+//        3596, 3584, 3571, 3559, 3546, 3533, 3519, 3506, 3492, 3478,     /* -15  -   -10.5 ℃ */
+//        3464, 3449, 3434, 3419, 3404, 3389, 3373, 3358, 3341, 3325,     /* -10  -   -5.5 ℃ */
+//        3309, 3292, 3275, 3258, 3241, 3223, 3205, 3187, 3169, 3151,     /* -5   -   -0.5 ℃ */
+//        3132, 3114, 3095, 3075, 3056, 3037, 3017, 2997, 2977, 2957,     /* 0    -   4.5 ℃ */
+//        2936, 2916, 2895, 2874, 2854, 2832, 2811, 2790, 2768, 2747,     /* 9    -   9.5 ℃ */
+//        2725, 2703, 2681, 2659, 2637, 2615, 2592, 2570, 2548, 2525,     /* 10   -   14.5 ℃ */
+//        2503, 2480, 2457, 2435, 2412, 2389, 2366, 2343, 2321, 2298,     /* 15   -   19.5 ℃ */
+//        2275, 2252, 2229, 2207, 2184, 2161, 2138, 2116, 2093, 2071,     /* 20   -   24.5 ℃ */
+//        2048, 2026, 2003, 1981, 1959, 1937, 1914, 1893, 1871, 1849,     /* 25   -   29.5 ℃ */
+//        1827, 1806, 1784, 1763, 1742, 1721, 1700, 1679, 1658, 1638,     /* 30   -   34.5 ℃ */
+//        1617, 1597, 1577, 1557, 1537, 1518, 1498, 1479, 1460, 1441,     /* 35   -   39.5 ℃ */
+//        1422, 1403, 1385, 1366, 1348, 1330, 1312, 1295, 1277, 1260,     /* 40   -   44.5 ℃ */
+//        1243, 1226, 1209, 1192, 1176, 1160, 1144, 1128, 1112, 1097,     /* 45   -   49.5 ℃ */
+//        1081, 1066, 1051, 1036, 1022, 1007,  993,  979,  965,  951,     /* 50   -   54.5 ℃ */
+//         938,  924,  911,  898,  885,  872,  860,  848,  835,  823,     /* 55   -   59.5 ℃ */
+//         811,  800,  788,  777,  765,  754,  743,  732,  722,  711,     /* 60   -   64.5 ℃ */
+//         701,  691,  681,  671,  661,  651,  642,  632,  623,  614,     /* 65   -   69.5 ℃ */
+//         605,  596,  588,  579,  571,  562,  554,  546,  538,  530,     /* 70   -   74.5 ℃ */
+//         522,  515,  507,  500,  493,  486,  478,  471,  465,  458,     /* 75   -   79.5 ℃ */
+//         451,  445,  438,  432,  426,  420,  414,  408,  402,  396,     /* 80   -   84.5 ℃ */
+//         390,  385,  379,  374,  368,  363,  358,  353,  348,  343,     /* 85   -   89.5 ℃ */
+//         338,  333,  328,  324,  319,  315,  310,  306,  301,  297,     /* 90   -   94.5 ℃ */
+//         293,  289,  285,  281,  277,  273,  269,  266,  262,  258,     /* 95   -   99.5 ℃ */
+//         255                                                            /* 100 ℃ */
+//};
 /* 温度  */
 const uint16_t mosTemperADC[mosTemperADCLen] = {
-        3707, 3697, 3687, 3676, 3665, 3654, 3643, 3632, 3620, 3608,     /* -20  -   -15.5 ¡æ */
+        4893, 4879, 4866, 4852, 4838, 4823, 4808, 4793, 4778, 4762, /* -20  -   -15.5 ℃ */
-        3596, 3584, 3571, 3559, 3546, 3533, 3519, 3506, 3492, 3478,     /* -15  -   -10.5 ¡æ */
+        4746, 4730, 4714, 4697, 4680, 4663, 4645, 4627, 4609, 4590, /* -15  -   -10.5 ℃ */
-        3464, 3449, 3434, 3419, 3404, 3389, 3373, 3358, 3341, 3325,     /* -10  -   -5.5 ¡æ */
+        4571, 4552, 4533, 4513, 4493, 4473, 4452, 4431, 4410, 4389, /* -10  -   -5.5 ℃ */
-        3309, 3292, 3275, 3258, 3241, 3223, 3205, 3187, 3169, 3151,     /* -5   -   -0.5 ¡æ */
+        4367, 4345, 4323, 4300, 4277, 4254, 4231, 4207, 4183, 4159, /* -5   -   -0.5 ℃ */
-        3132, 3114, 3095, 3075, 3056, 3037, 3017, 2997, 2977, 2957,     /* 0    -   4.5 ¡æ */
+        4134, 4109, 4084, 4059, 4034, 4008, 3982, 3956, 3929, 3903, /* 0    -   4.5 ℃ */
-        2936, 2916, 2895, 2874, 2854, 2832, 2811, 2790, 2768, 2747,     /* 9    -   9.5 ¡æ */
+        3876, 3849, 3821, 3794, 3766, 3738, 3710, 3682, 3654, 3625, /* 5    -   9.5 ℃ */
-        2725, 2703, 2681, 2659, 2637, 2615, 2592, 2570, 2548, 2525,     /* 10   -   14.5 ¡æ */
+        3596, 3568, 3539, 3510, 3480, 3451, 3422, 3392, 3362, 3333, /* 10   -   14.5 ℃ */
-        2503, 2480, 2457, 2435, 2412, 2389, 2366, 2343, 2321, 2298,     /* 15   -   19.5 ¡æ */
+        3303, 3273, 3243, 3213, 3183, 3153, 3123, 3093, 3063, 3033, /* 15   -   19.5 ℃ */
-        2275, 2252, 2229, 2207, 2184, 2161, 2138, 2116, 2093, 2071,     /* 20   -   24.5 ¡æ */
+        3003, 2972, 2942, 2912, 2882, 2852, 2822, 2792, 2762, 2733, /* 20   -   24.5 ℃ */
-        2048, 2026, 2003, 1981, 1959, 1937, 1914, 1893, 1871, 1849,     /* 25   -   29.5 ¡æ */
+        2703, 2673, 2644, 2614, 2585, 2556, 2527, 2498, 2469, 2440, /* 25   -   29.5 ℃ */
-        1827, 1806, 1784, 1763, 1742, 1721, 1700, 1679, 1658, 1638,     /* 30   -   34.5 ¡æ */
+        2412, 2383, 2355, 2327, 2299, 2271, 2243, 2216, 2189, 2162, /* 30   -   34.5 ℃ */
-        1617, 1597, 1577, 1557, 1537, 1518, 1498, 1479, 1460, 1441,     /* 35   -   39.5 ¡æ */
+        2135, 2108, 2081, 2055, 2029, 2003, 1977, 1952, 1926, 1901, /* 35   -   39.5 ℃ */
-        1422, 1403, 1385, 1366, 1348, 1330, 1312, 1295, 1277, 1260,     /* 40   -   44.5 ¡æ */
+        1876, 1852, 1827, 1803, 1779, 1755, 1732, 1709, 1686, 1663, /* 40   -   44.5 ℃ */
-        1243, 1226, 1209, 1192, 1176, 1160, 1144, 1128, 1112, 1097,     /* 45   -   49.5 ¡æ */
+        1640, 1618, 1596, 1574, 1552, 1531, 1510, 1489, 1468, 1447, /* 45   -   49.5 ℃ */
-        1081, 1066, 1051, 1036, 1022, 1007,  993,  979,  965,  951,     /* 50   -   54.5 ¡æ */
+        1427, 1407, 1387, 1368, 1349, 1330, 1311, 1292, 1274, 1256, /* 50   -   54.5 ℃ */
-         938,  924,  911,  898,  885,  872,  860,  848,  835,  823,     /* 55   -   59.5 ¡æ */
+        1238, 1220, 1203, 1185, 1168, 1151, 1135, 1119, 1102, 1086, /* 55   -   59.5 ℃ */
-         811,  800,  788,  777,  765,  754,  743,  732,  722,  711,     /* 60   -   64.5 ¡æ */
+        1071, 1055, 1040, 1025, 1010,  995,  981,  967,  953,  939, /* 60   -   64.5 ℃ */
-         701,  691,  681,  671,  661,  651,  642,  632,  623,  614,     /* 65   -   69.5 ¡æ */
+         925,  912,  898,  885,  872,  860,  847,  835,  822,  810, /* 65   -   69.5 ℃ */
-         605,  596,  588,  579,  571,  562,  554,  546,  538,  530,     /* 70   -   74.5 ¡æ */
+         799,  787,  775,  764,  753,  742,  731,  721,  710,  700, /* 70   -   74.5 ℃ */
-         522,  515,  507,  500,  493,  486,  478,  471,  465,  458,     /* 75   -   79.5 ¡æ */
+         690,  679,  670,  660,  650,  641,  631,  622,  613,  604, /* 75   -   79.5 ℃ */
-         451,  445,  438,  432,  426,  420,  414,  408,  402,  396,     /* 80   -   84.5 ¡æ */
+         596,  587,  578,  570,  562,  554,  546,  538,  530,  523, /* 80   -   84.5 ℃ */
-         390,  385,  379,  374,  368,  363,  358,  353,  348,  343,     /* 85   -   89.5 ¡æ */
+         515,  508,  500,  493,  486,  479,  472,  466,  459,  452, /* 85   -   89.5 ℃ */
-         338,  333,  328,  324,  319,  315,  310,  306,  301,  297,     /* 90   -   94.5 ¡æ */
+         446,  440,  433,  427,  421,  415,  409,  404,  398,  392, /* 90   -   94.5 ℃ */
-         293,  289,  285,  281,  277,  273,  269,  266,  262,  258,     /* 95   -   99.5 ¡æ */
+         387,  381,  376,  371,  366,  361,  355,  350,  346,  341, /* 95   -   99.5 ℃ */
-         255                                                            /* 100 ¡æ */
+         336                                                        /* 100 ℃ */
 };
 
 
-
-
 static uint16_t get_adc(uint8_t ADC_Channel);
+static uint16_t get_aftercalculationAdc(uint8_t ADC_Channel);
+static uint16_t middleAverageFilter(uint8_t ADC_Channel);
+
+/**
+  * @brief  获取计算后的adc的值
+  * @param  ADC_Channel ADC通道
+  * @retval None
+  */
+uint16_t get_aftercalculationAdc(uint8_t ADC_Channel)
+{
+    return middleAverageFilter(ADC_Channel);
+}
+
+#define N 6
+/**
+  * @brief  中位值平均滤波
+  * @param  ADC_Channel ADC通道
+  * @retval None
+  */
+uint16_t middleAverageFilter(uint8_t ADC_Channel)
+{
+    uint16_t i,j,k;
+    uint16_t temp,sum = 0;
+    uint16_t value_buf[N];
+    for(i = 0; i < N; ++i)
+    {
+        value_buf[i] = get_adc(ADC_Channel);
+    }
+    /*从小到大冒泡排序*/
+    for(j = 0; j < N-1; ++j)
+    {
+        for(k = 0; k < N-j-1; ++k)
+        {
+            if(value_buf[k] > value_buf[k+1])
+            {
+                temp = value_buf[k];
+                value_buf[k] = value_buf[k+1];
+                value_buf[k+1] = temp;
+            }
+        }
+    }
+    for(i = 2; i < N-2; ++i)
+    {
+        sum += value_buf[i];
+    }
+    return sum/(N-4);
+}
 
 /**
   * @brief  将采集的adc进行校准
@@ -97,13 +199,14 @@ uint16_t Get_ConversionVal(int16_t val)
   */
 uint16_t get_adc(uint8_t ADC_Channel)
 {
-    uint16_t val;
+    int16_t val;
     ADC_RegularChannelConfig(ADC1, ADC_Channel, 1, ADC_SampleTime_CyclesMode5);
 //    ADC_RegularChannelConfig(ADC1, ADC_Channel, 1, ADC_SampleTime_CyclesMode7);
     ADC_SoftwareStartConvCmd(ADC1, ENABLE);
     while(!ADC_GetFlagStatus(ADC1, ADC_FLAG_EOC));
     val = ADC_GetConversionValue(ADC1);
-    return val;
+//    return val;
+    return Get_ConversionVal(val);
 }
 
 /**
@@ -116,10 +219,12 @@ float get_CHG_CURR(void)
     float I;
     uint16_t I_ADC;
 
-    I_ADC = Get_ConversionVal(get_adc(CHG_CURR));
+//    I_ADC = Get_ConversionVal(get_adc(CHG_CURR));
+    I_ADC = get_aftercalculationAdc(CHG_CURR);
 //    I_ADC = get_adc(CHG_CURR);
 
-    I = (float)(I_ADC) / 4095 * 3.3 * P_CHG_CURR * 2;
+//    I = (float)(I_ADC) / 4095 * 3.3 * P_CHG_CURR * 2;
+    I = (float)(I_ADC) / 4095 * 2.5 * P_CHG_CURR;
 
 //    printf(" CHG_CURR I : %d /10000 \n", (int)(I * 10000));
 #ifdef enable_Printf_VI
@@ -140,10 +245,16 @@ float get_PV_VOLT_OUT(void)
     float V;
     uint16_t V_ADC;
 
-    V_ADC = Get_ConversionVal(get_adc(PV_VOLT_OUT));
+//    V_ADC = Get_ConversionVal(get_adc(PV_VOLT_OUT));
+    V_ADC = get_aftercalculationAdc(PV_VOLT_OUT);
 //    V_ADC = get_adc(PV_VOLT_OUT);
 
-    V = (float)(V_ADC) / 4095 * 3.3 * P_PV_VOLT_OUT;
+    V = (float)(V_ADC) / 4095 * 2.5 * P_PV_VOLT_OUT;
+//
+//    char buffer[30];
+//    memset(buffer, 0, sizeof(buffer));
+//    sprintf(buffer, " PV_VOLT_OUT ADC : %d \n", V_ADC);
+//    uart_dev_write(g_bat485_uart3_handle, buffer, sizeof(buffer));
 
 #ifdef enable_Printf_VI
     printf("\n PV_VOLT_OUT ADC : %d \n", V_ADC);
@@ -163,10 +274,12 @@ float get_DSG_CURR(void)
     float I;
     uint16_t I_ADC;
 
-    I_ADC = Get_ConversionVal(get_adc(DSG_CURR));
+//    I_ADC = Get_ConversionVal(get_adc(DSG_CURR));
+    I_ADC = get_aftercalculationAdc(DSG_CURR);
 //    I_ADC = get_adc(DSG_CURR);
 
-    I = (float)(I_ADC) / 4095 * 3.3 * P_DSG_CURR * 2;
+//    I = (float)(I_ADC) / 4095 * 3.3 * P_DSG_CURR * 2;
+    I = (float)(I_ADC) / 4095 * 2.5 * P_DSG_CURR;
 
 #ifdef enable_Printf_VI
     printf("\n DSG_CURR ADC : %d \n", I_ADC);
@@ -187,11 +300,13 @@ float get_PV1_VOLT_IN(void)
     uint16_t V_ADC;
 
 //    GPIO_WriteBit(G_FFMOS_CON1_GPIO, G_FFMOS_CON1_PIN, SET);
-    V_ADC = Get_ConversionVal(get_adc(PV1_VOLT_IN));
+//    V_ADC = Get_ConversionVal(get_adc(PV1_VOLT_IN));
+    V_ADC = get_aftercalculationAdc(PV1_VOLT_IN);
+
 //    V_ADC = get_adc(PV1_VOLT_IN);
 //    GPIO_WriteBit(G_FFMOS_CON1_GPIO, G_FFMOS_CON1_PIN, RESET);
 
-    V = (float)(V_ADC) / 4095 * 3.3 * P_PV1_VOLT_IN;
+    V = (float)(V_ADC) / 4095 * 2.5 * P_PV1_VOLT_IN;
 
 #ifdef enable_Printf_VI
     printf("\n PV1_VOLT_IN ADC : %d \n", V_ADC);
@@ -211,10 +326,11 @@ float get_PV_VOLT_IN1(void)
     float V;
     uint16_t V_ADC;
 
-    V_ADC = Get_ConversionVal(get_adc(PV_VOLT_IN1));
+//    V_ADC = Get_ConversionVal(get_adc(PV_VOLT_IN1));
+    V_ADC = get_aftercalculationAdc(PV_VOLT_IN1);
 //    V_ADC = get_adc(PV_VOLT_IN1);
 
-    V = (float)(V_ADC) / 4095 * 3.3 * P_PV_VOLT_IN1;
+    V = (float)(V_ADC) / 4095 * 2.5 * P_PV_VOLT_IN1;
 
 #ifdef enable_Printf_VI
     printf("\n PV_VOLT_IN1 ADC : %d \n", V_ADC);
@@ -240,7 +356,14 @@ float get_MOSFET_Temper(void)
     float T = 0;
     uint16_t T_ADC;
 
-    T_ADC = Get_ConversionVal(get_adc(MOSFET_Temper));
+//    T_ADC = Get_ConversionVal(get_adc(MOSFET_Temper));
+    T_ADC = get_aftercalculationAdc(MOSFET_Temper);
+
+//    char buffer[30];
+//    memset(buffer, 0, sizeof(buffer));
+//    sprintf(buffer, " T_ADC : %d \n", T_ADC);
+//    uart_dev_write(g_bat485_uart3_handle, buffer, sizeof(buffer));
+//    Delay_Ms(1);
 
     for (int i = 0; i < mosTemperADCLen; ++i) {
         if (T_ADC >= mosTemperADC[i]) {
@@ -276,11 +399,12 @@ float get_PV2_VOLT_IN(void)
     uint16_t V_ADC;
 
 //    GPIO_WriteBit(G_FFMOS_CON2_GPIO, G_FFMOS_CON2_PIN, SET);
-    V_ADC = Get_ConversionVal(get_adc(PV2_VOLT_IN));
+//    V_ADC = Get_ConversionVal(get_adc(PV2_VOLT_IN));
+    V_ADC = get_aftercalculationAdc(PV2_VOLT_IN);
 //    V_ADC = get_adc(PV2_VOLT_IN);
 //    GPIO_WriteBit(G_FFMOS_CON2_GPIO, G_FFMOS_CON2_PIN, RESET);
 
-    V = (float)(V_ADC) / 4095 * 3.3 * P_PV2_VOLT_IN;
+    V = (float)(V_ADC) / 4095 * 2.5 * P_PV2_VOLT_IN;
 
 #ifdef enable_Printf_VI
     printf("\n PV2_VOLT_IN ADC : %d \n", V_ADC);

App/src/inflash.c

@@ -12,11 +12,12 @@
 config_info g_slConfigInfo = {
         .constantCurrentV = 1000,
         .constantVoltageV = 1400,
-        .floatI = 10,
+        .floatI = 5,
         .startSolarOpenCircuitV = 1700,
         .stopSolarOpenCircuitV = 1500,
-        .noBatteryChargeV = 1200,
+        .constantVoltageChargeV = 1440,
-        .FloatTime = 10,
+        .trickleChargeC = 100,
+        .FloatTime = 3,
         .checkSolarOpenCircuitVTime = 10,
         .registerRefreshTime = 1,
         .resRefreshTime = 1,

App/src/mppt_control.c

@@ -19,11 +19,11 @@ static void TrickleCharge(void);
 static void ConstantCurrentCharge(void);
 static void ConstantVoltageCharge(void);
 static void FloatingCharge(void);
-static void NoBatteryCharge(void);
+//static void NoBatteryCharge(void);
 
 
 /* 占空比 */
-float g_duty_ratio = 0.7;
+float g_duty_ratio = 0.8;
 /* 用于确定工作模式 */
 //static uint8_t modeFlag = 2;
 
@@ -149,35 +149,35 @@ void printf_data(void)
     printf("\n");
 }
 
-float_t get_capturedata(float_t (*fun)(void))
+//float_t get_capturedata(float_t (*fun)(void))
-{
+//{
-    float_t temp1;
+//    float_t temp1;
-    float_t temp[3];
+//    float_t temp[3];
-
+//
-    for (int i = 0; i < 3; ++i) {
+//    for (int i = 0; i < 3; ++i) {
-        temp[i] = fun();
+//        temp[i] = fun();
-//        Delay_Us(1);
+////        Delay_Us(1);
-    }
+//    }
-
+//
-    if (temp[0] > temp[1]) {
+//    if (temp[0] > temp[1]) {
-        temp1 = temp[0];
+//        temp1 = temp[0];
-        temp[0] = temp[1];
+//        temp[0] = temp[1];
-        temp[1] = temp1;
+//        temp[1] = temp1;
-    }
+//    }
-
+//
-    if (temp[0] > temp[2]) {
+//    if (temp[0] > temp[2]) {
-        temp1 = temp[0];
+//        temp1 = temp[0];
-        temp[0] = temp[2];
+//        temp[0] = temp[2];
-        temp[2] = temp1;
+//        temp[2] = temp1;
-        if (temp[1] > temp[2]) {
+//        if (temp[1] > temp[2]) {
-            temp1 = temp[1];
+//            temp1 = temp[1];
-            temp[1] = temp[2];
+//            temp[1] = temp[2];
-            temp[2] = temp1;
+//            temp[2] = temp1;
-        }
+//        }
-    }
+//    }
-
+//
-    return temp[1];
+//    return temp[1];
-}
+//}
 
 //uint16_t get_mpptMode(void)
 //{
@@ -230,7 +230,10 @@ void mppt_constantVoltage(float InVoltage)
 //    allError += error;
 //    printf("111\n");
 
-    float_t pv1Volt = get_capturedata(get_PV1_VOLT_IN);
+//    float_t pv1Volt = get_capturedata(get_PV1_VOLT_IN);
+
+//    float_t pv1Volt = get_PV1_VOLT_IN();
+    float_t pv1Volt = g_Mppt_Para.Input_Voltage;
 //    printf("volt in : %d \n", pv1Volt);
     float_t error = pv1Volt - InVoltage;
 //    float_t error = InVoltage - pv1Volt;
@@ -397,7 +400,14 @@ void mppt_constantCurrentO(float outCurrent)
   */
 void TrickleCharge(void)
 {
-    mppt_constantCurrentO(2);
+    static float_t TrickleChargeC;
+    static uint8_t onlyOnce = 1;
+    if (onlyOnce) {
+        TrickleChargeC = (float_t)g_slConfigInfo.trickleChargeC / 100;
+        onlyOnce = 0;
+    }
+    printf("Trickle\n");
+    mppt_constantCurrentO(TrickleChargeC + g_Mppt_Para.Discharg_Current);
 }
 
 /**
@@ -410,6 +420,7 @@ void ConstantCurrentCharge(void)
 {
 //    mppt_readJust();
     mppt_constantVoltage(18);
+//    printf("ConstantCurrent\n");
 
 }
 
@@ -421,7 +432,14 @@ void ConstantCurrentCharge(void)
   */
 void ConstantVoltageCharge(void)
 {
-    mppt_constantVoltageO(14.5);
+    static float_t ConstantVoltageChargeV;
+    static uint8_t onlyOnce = 1;
+    if (onlyOnce) {
+        ConstantVoltageChargeV = (float_t)g_slConfigInfo.constantVoltageChargeV / 100;
+        onlyOnce = 0;
+    }
+
+    mppt_constantVoltageO(ConstantVoltageChargeV);
 }
 
 /**
@@ -436,17 +454,17 @@ void FloatingCharge(void)
     static uint32_t numLenFlag;
     static uint8_t onlyOnce = 1;
     if (onlyOnce) {
-        numLenFlag = g_slConfigInfo.FloatTime * 1000 / 5;
+        numLenFlag = g_slConfigInfo.FloatTime * 1000;
         onlyOnce = 0;
     }
 
+    printf("float\n");
     TIM_SetCompare4(TIM4, 0);
 
     if (numLenFlag == ++num) {
         num = 0;
         ConstantVoltageCharge();
         g_Mppt_Para.MPPT_Mode = CONSTANTVOLTAGE;
-//        printf("float charge \n");
     }
 
 }
@@ -459,14 +477,14 @@ void FloatingCharge(void)
   */
 void NoBatteryCharge(void)
 {
-    static float_t NoBatteryChargeV;
+//    static float_t NoBatteryChargeV;
-    static uint8_t onlyOnce = 1;
+//    static uint8_t onlyOnce = 1;
-    if (onlyOnce) {
+//    if (onlyOnce) {
-        NoBatteryChargeV = (float_t)g_slConfigInfo.noBatteryChargeV / 100;
+//        NoBatteryChargeV = (float_t)g_slConfigInfo.noBatteryChargeV / 100;
-        onlyOnce = 0;
+//        onlyOnce = 0;
-    }
+//    }
 
-    mppt_constantVoltageO(NoBatteryChargeV);
+    mppt_constantVoltageO(14.2);
 
 //    if ((g_Mppt_Para.Battery_Voltage - NoBatteryChargeV > 0.2 && g_Mppt_Para.Charg_Current < 0.1)
 //            || (NoBatteryChargeV - g_Mppt_Para.Battery_Voltage > 0.1 && g_Mppt_Para.Charg_Current > 0.5)) {
@@ -474,13 +492,13 @@ void NoBatteryCharge(void)
 //        g_Mppt_Para.MPPT_Mode = CONSTANTCURRENT;
 //    }
 
-    if (!overTemperature) {
+//    if (!overTemperature) {
-        if (!(g_Mppt_Para.Charg_Current - g_Mppt_Para.Discharg_Current < 0.3
+//        if (!(g_Mppt_Para.Charg_Current - g_Mppt_Para.Discharg_Current < 0.3
-                && g_Mppt_Para.Discharg_Current - g_Mppt_Para.Charg_Current < 0.3)) {
+//                && g_Mppt_Para.Discharg_Current - g_Mppt_Para.Charg_Current < 0.3)) {
-            ConstantCurrentCharge();
+//            ConstantCurrentCharge();
-            g_Mppt_Para.MPPT_Mode = CONSTANTCURRENT;
+//            g_Mppt_Para.MPPT_Mode = CONSTANTCURRENT;
-        }
+//        }
-    }
+//    }
 
 }
 
@@ -495,6 +513,7 @@ void MpptContorl(void)
     case CONSTANTCURRENT:
 //        printf("222222\n");
         ConstantCurrentCharge();
+//        ConstantVoltageCharge();
         break;
 
     case CONSTANTVOLTAGE:
@@ -507,10 +526,10 @@ void MpptContorl(void)
         FloatingCharge();
         break;
 
-    case NoBattery:
+//    case NoBattery:
-//        printf("555555555555555\n");
+////        printf("555555555555555\n");
-        NoBatteryCharge();
+//        NoBatteryCharge();
-        break;
+//        break;
 
     default:
         break;
@@ -624,29 +643,50 @@ void MpptMode(void)
         return;
     }
 
-    if ((g_Mppt_Para.Charg_Current - g_Mppt_Para.Discharg_Current < 0.03
+//    if (((g_Mppt_Para.Charg_Current - g_Mppt_Para.Discharg_Current < 0.03
-            && g_Mppt_Para.Discharg_Current - g_Mppt_Para.Charg_Current < 0.03)
+//            && g_Mppt_Para.Discharg_Current - g_Mppt_Para.Charg_Current < 0.03)
-            || g_Mppt_Para.Battery_Voltage < 6
+//            && (g_Mppt_Para.Battery_Voltage < ConstantVoltageV - 1
-            || g_Mppt_Para.Battery_Voltage > 16
+//            || g_Mppt_Para.Battery_Voltage > ConstantVoltageV + 1))
-            || g_Mppt_Para.MPPT_Mode == NoBattery) {
+//            || g_Mppt_Para.MPPT_Mode == NoBattery) {
-        g_Mppt_Para.MPPT_Mode = NoBattery;
+//        g_Mppt_Para.MPPT_Mode = NoBattery;
+//        return;
+//    }
+
+//    if (((ConstantVoltageV < g_Mppt_Para.Battery_Voltage) &&
+//            (FloatI > g_Mppt_Para.Charg_Current)) || g_Mppt_Para.MPPT_Mode == FLOAT) {
+//        g_Mppt_Para.MPPT_Mode = FLOAT;
+//        return;
+//    }
+    if ((g_Mppt_Para.Charg_Current - g_Mppt_Para.Discharg_Current < 0.05
+            && g_Mppt_Para.Discharg_Current - g_Mppt_Para.Charg_Current < 0.05)
+            || g_Mppt_Para.Battery_Voltage > 16 || g_Mppt_Para.Battery_Voltage < 8) {
+//            || g_Mppt_Para.MPPT_Mode == NoBattery) {
+//        g_Mppt_Para.MPPT_Mode = NoBattery;
+        g_Mppt_Para.MPPT_Mode = CONSTANTVOLTAGE;
         return;
     }
 
+    if ((((ConstantCurrentV + 0.2) < g_Mppt_Para.Battery_Voltage)
+            &&((ConstantVoltageV - 0.2) >= g_Mppt_Para.Battery_Voltage))
+            &&(g_Mppt_Para.Charg_Current - g_Mppt_Para.Discharg_Current > 0.1)) {
+        g_Mppt_Para.MPPT_Mode = CONSTANTCURRENT;
+        return;
+    }
+//    if ((g_Mppt_Para.Charg_Current - g_Mppt_Para.Discharg_Current > 4)) {
+//        g_Mppt_Para.MPPT_Mode = CONSTANTCURRENT;
+//        return;
+//    }
+
     if (((ConstantVoltageV < g_Mppt_Para.Battery_Voltage) &&
-            (FloatI > g_Mppt_Para.Charg_Current)) || g_Mppt_Para.MPPT_Mode == FLOAT) {
+            (FloatI > g_Mppt_Para.Charg_Current))) {
         g_Mppt_Para.MPPT_Mode = FLOAT;
         return;
     }
 
-    if (((ConstantCurrentV + 0.4) < g_Mppt_Para.Battery_Voltage) &&
+    if (((ConstantVoltageV < g_Mppt_Para.Battery_Voltage)
-            ((ConstantVoltageV - 0.4) >= g_Mppt_Para.Battery_Voltage)) {
+            &&(FloatI + 0.1 <= g_Mppt_Para.Charg_Current))) {
-        g_Mppt_Para.MPPT_Mode = CONSTANTCURRENT;
+//            || (g_Mppt_Para.Charg_Current - g_Mppt_Para.Discharg_Current < 0.03
-        return;
+//               && g_Mppt_Para.Discharg_Current - g_Mppt_Para.Charg_Current < 0.03)) {
-    }
-
-    if ((ConstantVoltageV < g_Mppt_Para.Battery_Voltage) &&
-            (FloatI + 0.1 <= g_Mppt_Para.Charg_Current)) {
 
 //        printf("mppt mode \n");
 //        printf(" vout : %d/100 \n", (int)(g_Mppt_Para.Battery_Voltage * 100));
@@ -695,8 +735,29 @@ void test(void)
 
 //    mppt_constantCurrentO(1);
 
-    g_Mppt_Para.Charg_Current = get_capturedata(get_CHG_CURR);
+//    g_Mppt_Para.Charg_Current = get_capturedata(get_CHG_CURR);
-    g_Mppt_Para.Discharg_Current = get_capturedata(get_DSG_CURR);
+//    g_Mppt_Para.Discharg_Current = get_capturedata(get_DSG_CURR);
+//    g_Mppt_Para.Output_Voltage = get_capturedata(get_PV_VOLT_OUT);
+//    g_Mppt_Para.Battery_Voltage = g_Mppt_Para.Output_Voltage;
+    g_Mppt_Para.Charg_Current = get_CHG_CURR();
+    g_Mppt_Para.Discharg_Current = get_DSG_CURR();
+    g_Mppt_Para.Output_Voltage = get_PV_VOLT_OUT();
+    g_Mppt_Para.Input_Voltage  = get_PV1_VOLT_IN();
+//    g_Mppt_Para.Battery_Voltage = g_Mppt_Para.Output_Voltage;
+
+//    static float_t Volt = 0.7;
+//    static float_t Curr = 5.5;
+    static float_t Res = 0.7 / 5.5;
+    static float_t inBatteryCurr;
+    inBatteryCurr = g_Mppt_Para.Charg_Current - g_Mppt_Para.Discharg_Current;
+    if (inBatteryCurr > 0.5) {
+        g_Mppt_Para.Battery_Voltage = g_Mppt_Para.Output_Voltage - inBatteryCurr * Res;
+    }
+
+
+
+
+//    mppt_constantVoltage(18);
 
 //    if (g_Mppt_Para.MPPT_Mode == CONSTANTCURRENT
 //            || g_Mppt_Para.MPPT_Mode == CONSTANTVOLTAGE) {
@@ -704,18 +765,21 @@ void test(void)
 //        g_Mppt_Para.Battery_Voltage = get_capturedata(get_PV_VOLT_OUT)
 //                - g_impedance * (g_Mppt_Para.Charg_Current - g_Mppt_Para.Discharg_Current);
 //    } else {
-        g_Mppt_Para.Battery_Voltage = get_capturedata(get_PV_VOLT_OUT);
+//        g_Mppt_Para.Battery_Voltage = get_capturedata(get_PV_VOLT_OUT);
 //    }
 
 //    voltOut = get_capturedata(get_PV_VOLT_OUT);
 //    g_Mppt_Para.Battery_Voltage = voltOut - g_impedance * (g_Mppt_Para.Charg_Current - g_Mppt_Para.Discharg_Current);
 
 
+//    ConstantVoltageCharge();
+//    return;
+
     if (!overTemperature) {
         MpptMode();
+        MpptContorl();
     }
 
-    MpptContorl();
 
 //    mppt_constantVoltageO(12);
 

App/src/task.c

@@ -4,6 +4,7 @@
  *  Created on: 2024Äê6ÔÂ24ÈÕ
  *      Author: psx
  */
+#include  <string.h>
 
 #include "task.h"
 
@@ -25,7 +26,7 @@
 
 void stop_mpptWork(void)
 {
-    GPIO_WriteBit(EnPowerSupply_GPIO, EnPowerSupply_PIN, SET);
+//    GPIO_WriteBit(EnPowerSupply_GPIO, EnPowerSupply_PIN, SET);
     g_duty_ratio = 0.7;
     TIM_Cmd(TIM3, DISABLE);
     TIM_SetCompare4(TIM4, 0);
@@ -57,20 +58,60 @@ void Task_RunLED(void)
 //    uart_sendstr(g_gw485_uart4_handle, "is gw485\n");
 //    uart_sendstr(g_bat485_uart3_handle, "is bat485\n");get_PV1_VOLT_IN();
 
-    printf(" \n");
+//    printf(" \n");
-    printf(" duty_ratio : %d/1000 \n", (int)(g_duty_ratio * 1000));
+//    printf(" duty_ratio : %d/1000 \n", (int)(g_duty_ratio * 1000));
+//
+//    printf(" vout : %d/100 \n", (int)(g_Mppt_Para.Battery_Voltage * 100));
+//    printf(" Iout : %d/100 \n", (int)(g_Mppt_Para.Charg_Current * 100));
+//    printf(" Idisout : %d/100 \n", (int)(g_Mppt_Para.Discharg_Current * 100));
+//    printf(" mosT : %d/10 \n", (int)(g_Mppt_Para.HighSideMos_Temperature * 10));
+//    printf(" mosState : %d \n", (int)(g_Mppt_Para.DischargMos_State));
+////    printf(" mosState : %d \n", GPIO_ReadOutputDataBit(POW_OUT_CON_GPIO, POW_OUT_CON_PIN));
+////    printf(" mosState : %d \n", GPIO_ReadInputDataBit(DSG_PROT_GPIO, DSG_PROT_PIN));
+//
+//    printf(" 0.没有工作; 1.涓流模式; 2.恒流模式; 3.恒压模式; 4.浮充模式; 5.没有电池 : %d \n", g_Mppt_Para.MPPT_Mode);
+//
+//    printf(" \n");
 
-    printf(" vout : %d/100 \n", (int)(g_Mppt_Para.Battery_Voltage * 100));
+//    uart_sendstr(g_bat485_uart3_handle, " \n");
-    printf(" Iout : %d/100 \n", (int)(g_Mppt_Para.Charg_Current * 100));
-    printf(" Idisout : %d/100 \n", (int)(g_Mppt_Para.Discharg_Current * 100));
-    printf(" mosT : %d/10 \n", (int)(g_Mppt_Para.HighSideMos_Temperature * 10));
-    printf(" mosState : %d \n", (int)(g_Mppt_Para.DischargMos_State));
-//    printf(" mosState : %d \n", GPIO_ReadOutputDataBit(POW_OUT_CON_GPIO, POW_OUT_CON_PIN));
-//    printf(" mosState : %d \n", GPIO_ReadInputDataBit(DSG_PROT_GPIO, DSG_PROT_PIN));
 
-    printf(" 0.没有工作; 1.涓流模式; 2.恒流模式; 3.恒压模式; 4.浮充模式; 5.没有电池 : %d \n", g_Mppt_Para.MPPT_Mode);
+    uart_dev_write(g_bat485_uart3_handle, " \n", sizeof(" \n"));
+
+    char buffer[80];
+    memset(buffer, 0, sizeof(buffer));
+    sprintf(buffer, " duty_ratio : %d/1000 \n", (int)(g_duty_ratio * 1000));
+    uart_dev_write(g_bat485_uart3_handle, buffer, sizeof(buffer));
+
+    memset(buffer, 0, sizeof(buffer));
+    sprintf(buffer, " vout : %d/100 \n", (int)(g_Mppt_Para.Output_Voltage * 100));
+    uart_dev_write(g_bat485_uart3_handle, buffer, sizeof(buffer));
+
+    memset(buffer, 0, sizeof(buffer));
+    sprintf(buffer, " vBattery : %d/100 \n", (int)(g_Mppt_Para.Battery_Voltage * 100));
+    uart_dev_write(g_bat485_uart3_handle, buffer, sizeof(buffer));
+
+    memset(buffer, 0, sizeof(buffer));
+    sprintf(buffer, " Iout : %d/100 \n", (int)(g_Mppt_Para.Charg_Current * 100));
+    uart_dev_write(g_bat485_uart3_handle, buffer, sizeof(buffer));
+
+    memset(buffer, 0, sizeof(buffer));
+    sprintf(buffer, " Idisout : %d/100 \n", (int)(g_Mppt_Para.Discharg_Current * 100));
+    uart_dev_write(g_bat485_uart3_handle, buffer, sizeof(buffer));
+
+    memset(buffer, 0, sizeof(buffer));
+    sprintf(buffer, " mosT : %d/10 \n",  (int)(g_Mppt_Para.HighSideMos_Temperature * 10));
+    uart_dev_write(g_bat485_uart3_handle, buffer, sizeof(buffer));
+
+    memset(buffer, 0, sizeof(buffer));
+    sprintf(buffer, " mosState : %d \n",  (int)(g_Mppt_Para.DischargMos_State));
+    uart_dev_write(g_bat485_uart3_handle, buffer, sizeof(buffer));
+
+    memset(buffer, 0, sizeof(buffer));
+    sprintf(buffer, " 0.没有工作; 1.涓流模式; 2.恒流模式; 3.恒压模式; 4.浮充模式; 5.没有电池 : %d \n",  g_Mppt_Para.MPPT_Mode);
+    uart_dev_write(g_bat485_uart3_handle, buffer, sizeof(buffer));
+
+    uart_dev_write(g_bat485_uart3_handle, " \n", sizeof(" \n"));
 
-    printf(" \n");
 
 //    printf("vout : %d/100 \n", (int)(get_capturedata(get_PV_VOLT_OUT) * 100));
 
@@ -106,8 +147,12 @@ void Task_startMpptControl(void)
 
     if (g_slConfigInfo.checkSolarOpenCircuitVTime == ++checkSolarOpenCircuitVTimeFlag) {
         checkSolarOpenCircuitVTimeFlag = 0;
-        g_Mppt_Para.Solar_Open_Circuit_Voltage = get_capturedata(get_PV1_VOLT_IN);
+        g_Mppt_Para.Solar_Open_Circuit_Voltage = get_PV1_VOLT_IN();
-        printf("volt in : %d/100 \n", (int)(g_Mppt_Para.Solar_Open_Circuit_Voltage * 100));
+//        printf("volt in : %d/100 \n", (int)(g_Mppt_Para.Solar_Open_Circuit_Voltage * 100));
+        char buff[50];
+        memset(buff, 0, sizeof(buff));
+        sprintf(buff, "volt in : %d/100 \n",  (int)(g_Mppt_Para.Solar_Open_Circuit_Voltage * 100));
+        uart_dev_write(g_bat485_uart3_handle, buff, sizeof(buff));
 
         if (g_Mppt_Para.Solar_Open_Circuit_Voltage
              > ((float_t)g_slConfigInfo.startSolarOpenCircuitV / 100)) {
@@ -132,9 +177,9 @@ void Task_softStart(void)
 
     num++;
 
-    if (num == 1) {
+//    if (num == 1) {
-        GPIO_WriteBit(EnPowerSupply_GPIO, EnPowerSupply_PIN, RESET);
+//        GPIO_WriteBit(EnPowerSupply_GPIO, EnPowerSupply_PIN, RESET);
-    }
+//    }
 
     if (num < 5) {
         TIM_SetCompare4(TIM4, 100);
@@ -167,6 +212,7 @@ void Task_usart(void)
 {
     read_and_process_uart_data(g_gw485_uart4_handle);
 //    read_and_process_uart_data(g_bat485_uart3_handle);
+//    uart_dev_write(g_bat485_uart3_handle, "hello world \n", sizeof("hello world \n"));
     return;
 }
 
@@ -201,13 +247,19 @@ void Task_refreshRegister(void)
 
     if (g_slConfigInfo.registerRefreshTime == ++checkRegisterRefreshTimeFlag) {
         checkRegisterRefreshTimeFlag = 0;
-        g_Mppt_Para.Battery_Voltage = get_capturedata(get_PV_VOLT_OUT);
+//        g_Mppt_Para.Battery_Voltage = get_capturedata(get_PV_VOLT_OUT);
-        g_Mppt_Para.Charg_Current = get_capturedata(get_CHG_CURR);
+//        g_Mppt_Para.Charg_Current = get_capturedata(get_CHG_CURR);
-        g_Mppt_Para.Discharg_Current = get_capturedata(get_DSG_CURR);
+//        g_Mppt_Para.Discharg_Current = get_capturedata(get_DSG_CURR);
-        g_Mppt_Para.HighSideMos_Temperature = get_capturedata(get_MOSFET_Temper);
+//        g_Mppt_Para.HighSideMos_Temperature = get_capturedata(get_MOSFET_Temper);
+        g_Mppt_Para.Battery_Voltage = get_PV_VOLT_OUT();
+        g_Mppt_Para.Charg_Current = get_CHG_CURR();
+        g_Mppt_Para.Discharg_Current = get_DSG_CURR();
+        g_Mppt_Para.HighSideMos_Temperature = get_MOSFET_Temper();
         g_Mppt_Para.DischargMos_State = GPIO_ReadOutputDataBit(POW_OUT_CON_GPIO, POW_OUT_CON_PIN)
                                                 && GPIO_ReadInputDataBit(DSG_PROT_GPIO, DSG_PROT_PIN);
-        g_Mppt_Para.Solar_Open_Circuit_Voltage = get_capturedata(get_PV1_VOLT_IN);
+//        g_Mppt_Para.DischargMos_State = GPIO_ReadOutputDataBit(POW_OUT_CON_GPIO, POW_OUT_CON_PIN);
+//        g_Mppt_Para.Solar_Open_Circuit_Voltage = get_capturedata(get_PV1_VOLT_IN);
+        g_Mppt_Para.Solar_Open_Circuit_Voltage = get_PV1_VOLT_IN();
 
         if (g_Mppt_Para.HighSideMos_Temperature < g_slConfigInfo.HighSideMosTemperature_start) {
             if (overTemperature == 2) {
@@ -219,7 +271,9 @@ void Task_refreshRegister(void)
         }
 
         if (g_Mppt_Para.HighSideMos_Temperature > g_slConfigInfo.HighSideMosTemperature_end) {
-            g_Mppt_Para.MPPT_Mode = NoBattery;
+//            g_Mppt_Para.MPPT_Mode = NoBattery;
+            g_duty_ratio = 0.5;
+            Set_duty_ratio(&g_duty_ratio);
             overTemperature = 1;
         }
 
@@ -352,13 +406,17 @@ void Task_impedanceCalculation(void)
 
         TIM_SetCompare4(TIM4, 420);
         Delay_Ms(5);
-        currOne = get_capturedata(get_CHG_CURR) - get_capturedata(get_DSG_CURR);
+//        currOne = get_capturedata(get_CHG_CURR) - get_capturedata(get_DSG_CURR);
-        voltOne = get_capturedata(get_PV_VOLT_OUT);
+//        voltOne = get_capturedata(get_PV_VOLT_OUT);
+        currOne = get_CHG_CURR() - get_DSG_CURR();
+        voltOne = get_PV_VOLT_OUT();
 
-        TIM_SetCompare4(TIM4, 350);
+        TIM_SetCompare4(TIM4, 300);
         Delay_Ms(5);
-        currTwo = get_capturedata(get_CHG_CURR) - get_capturedata(get_DSG_CURR);
+//        currTwo = get_capturedata(get_CHG_CURR) - get_capturedata(get_DSG_CURR);
-        voltTwo = get_capturedata(get_PV_VOLT_OUT);
+//        voltTwo = get_capturedata(get_PV_VOLT_OUT);
+        currTwo = get_CHG_CURR() - get_DSG_CURR();
+        voltTwo = get_PV_VOLT_OUT();
 
         g_impedance = (voltOne - voltTwo) / (currOne - currTwo);
 
@@ -434,11 +492,23 @@ void g_Mppt_Para_Init(void)
     g_Mppt_Para.Access_Node_Type = defaultValue.access_Node_Type;
     g_Mppt_Para.Communication_Methods = defaultValue.communication_Methods;
 
-    g_Mppt_Para.Battery_Voltage = get_capturedata(get_PV_VOLT_OUT);
+//    g_Mppt_Para.Output_Voltage = get_capturedata(get_PV_VOLT_OUT);
-    g_Mppt_Para.Charg_Current = get_capturedata(get_CHG_CURR);
+//    g_Mppt_Para.Battery_Voltage = g_Mppt_Para.Output_Voltage;
-    g_Mppt_Para.Discharg_Current = get_capturedata(get_DSG_CURR);
+//    g_Mppt_Para.Charg_Current = get_capturedata(get_CHG_CURR);
-    g_Mppt_Para.Solar_Open_Circuit_Voltage = get_capturedata(get_PV1_VOLT_IN);
+//    g_Mppt_Para.Discharg_Current = get_capturedata(get_DSG_CURR);
-    g_Mppt_Para.HighSideMos_Temperature = get_capturedata(get_MOSFET_Temper);
+//    g_Mppt_Para.Solar_Open_Circuit_Voltage = get_capturedata(get_PV1_VOLT_IN);
+//    g_Mppt_Para.HighSideMos_Temperature = get_capturedata(get_MOSFET_Temper);    g_Mppt_Para.Output_Voltage = get_capturedata(get_PV_VOLT_OUT);
+
+    g_Mppt_Para.Output_Voltage = get_PV_VOLT_OUT();
+    g_Mppt_Para.Battery_Voltage = g_Mppt_Para.Output_Voltage;
+    g_Mppt_Para.Charg_Current = get_CHG_CURR();
+    g_Mppt_Para.Discharg_Current = get_DSG_CURR();
+    g_Mppt_Para.Solar_Open_Circuit_Voltage = get_PV1_VOLT_IN();
+    g_Mppt_Para.HighSideMos_Temperature = get_MOSFET_Temper();
+
+    if (g_Mppt_Para.Battery_Voltage < 1 || g_Mppt_Para.Battery_Voltage > 9) {
+        GPIO_WriteBit(POW_OUT_CON_GPIO, POW_OUT_CON_PIN, SET);
+    }
     g_Mppt_Para.DischargMos_State = GPIO_ReadOutputDataBit(POW_OUT_CON_GPIO, POW_OUT_CON_PIN)
                                             && GPIO_ReadInputDataBit(DSG_PROT_GPIO, DSG_PROT_PIN);
     g_Mppt_Para.MPPT_Mode = NoWork;
@@ -498,8 +568,11 @@ void hardware_Init(void)
     SPI_Flash_Init();
     POW_OUT_CON_Init();
     DSG_PROT_Init();
-    EnPowerSupply_Init();
+//    EnPowerSupply_Init();
 
+//    Set_duty_ratio(&g_duty_ratio);
+
+    uart_dev_write(g_bat485_uart3_handle, " hello world \n", sizeof(" hello world \n"));
     TIM3_Init(1);
 }
 

App/src/uart_dev.c

@@ -102,7 +102,8 @@ device_handle uart_dev_init(void)
 void uart_init(uartIndex_e uart_index, int baud)
 {
     if (uart_index == BAT485_UART_INDEX) {
-        BAT_485_Init(uart_devices[0].uart_baudrate);
+//        BAT_485_Init(uart_devices[0].uart_baudrate);
+        BAT_485_Init(115200);
     } else if (uart_index == GW485_UART_INDEX) {
         GW_485_Init(uart_devices[1].uart_baudrate);
     }
@@ -227,9 +228,12 @@ void uart_dev_write(device_handle device, void *data, int len)
 #endif
 
    for (int i = 0; i < len; i++) {
-       uart_putchar(device, ((u_int8_t *)data)[i]);
+//       uart_putchar(device, ((u_int8_t *)data)[i]);
+       uart_putchar(device, ((char *)data)[i]);
    }
 
+   Delay_Ms(1);
+
 #if rs485_send_enable
    if(device == g_bat485_uart3_handle){
        bat485_tx_disenabla();

Hardware/src/adc.c

@@ -1,7 +1,6 @@
 #include <adc.h>
 
 
-
 int16_t Calibrattion_Val = 0;
 
 //ADC对应GPIO初始化配置以及ADC初始化配置

Hardware/src/gpio.c

@@ -66,8 +66,8 @@ void POW_OUT_CON_Init(void)
     GPIO_InitStructure.GPIO_Speed = GPIO_Speed_50MHz;
     GPIO_Init(POW_OUT_CON_GPIO, &GPIO_InitStructure);
 
-    GPIO_WriteBit(POW_OUT_CON_GPIO, POW_OUT_CON_PIN, SET);
+//    GPIO_WriteBit(POW_OUT_CON_GPIO, POW_OUT_CON_PIN, SET);
-//    GPIO_WriteBit(POW_OUT_CON_GPIO, POW_OUT_CON_PIN, RESET);
+    GPIO_WriteBit(POW_OUT_CON_GPIO, POW_OUT_CON_PIN, RESET);
 }
 
 void EXTI2_IRQHandler(void) __attribute__((interrupt("WCH-Interrupt-fast")));

Hardware/src/pwm.c

@@ -52,8 +52,8 @@ void PWM_TIM_Configuration(void)
 
 void Set_duty_ratio(float *duty_ratio)
 {
-    if (*duty_ratio < 0.5) {
+    if (*duty_ratio < 0.1) {
-        *duty_ratio = 0.5;
+        *duty_ratio = 0.1;
 //        return;
     } else if (*duty_ratio > 0.9) {
         *duty_ratio = 0.9;

Hardware/src/tim.c

@@ -50,7 +50,7 @@ void TIM3_Int_Init(uint16_t arr, uint16_t psc)
     NVIC_InitStructure.NVIC_IRQChannelCmd = ENABLE;           //使能通道1中断
     NVIC_Init(&NVIC_InitStructure); //初始化NVIC
 
-    TIM_Cmd(TIM3, ENABLE); //TIM3使能
+//    TIM_Cmd(TIM3, ENABLE); //TIM3使能
 }
 
 void TIM3_IRQHandler(void)

obj/App/src/collect_Conversion.d

@@ -26,7 +26,10 @@ App/src/collect_Conversion.o: ../App/src/collect_Conversion.c \
  D:\psx\MPPT\git\Peripheral\inc/ch32l103_misc.h \
  D:\psx\MPPT\git\Peripheral\inc/ch32l103_lptim.h \
  D:\psx\MPPT\git\Peripheral\inc/ch32l103_opa.h \
- D:\psx\MPPT\git\Hardware\inc/adc.h D:\psx\MPPT\git\Hardware\inc/gpio.h
+ D:\psx\MPPT\git\Hardware\inc/adc.h D:\psx\MPPT\git\Hardware\inc/gpio.h \
+ D:\psx\MPPT\git\App\inc/uart_dev.h \
+ D:\psx\MPPT\git\Drivers\RingQueue/ring_queue.h \
+ D:\psx\MPPT\git\Hardware\inc/rs485.h
 
 D:\psx\MPPT\git\App\inc/collect_Conversion.h:
 
@@ -89,3 +92,9 @@ D:\psx\MPPT\git\Peripheral\inc/ch32l103_opa.h:
 D:\psx\MPPT\git\Hardware\inc/adc.h:
 
 D:\psx\MPPT\git\Hardware\inc/gpio.h:
+
+D:\psx\MPPT\git\App\inc/uart_dev.h:
+
+D:\psx\MPPT\git\Drivers\RingQueue/ring_queue.h:
+
+D:\psx\MPPT\git\Hardware\inc/rs485.h: